BENDIX TABS-6 Service Data page 11

1st Digit
2 2 Sensors
4 4 Sensors
2nd Digit
1 1 Modulator
2 2 Modulators
3 3 Modulators
3rd Digit
1 Axle
2 Side
3 Dolly-Axle
4 MOD1 Axle - MOD2 Dolly-Axle
5 MOD1 Axle - MOD2 Lift Axle Detection
6 Side (MOD1, MOD2) - MOD3 Dolly-Axle
CHART 6 – ABS COnFIGURATIOnS
1st 2nd Diagnostic Trouble Code (DTC)
Digit Digit
1 1 No DTCs
2 1 SL Sensor signal valid - large air gap
3 1 SR Sensor signal valid - large air gap
4 1 SAL Sensor signal valid - large air gap
5 1 SAR Sensor signal valid - large air gap
2 2 SL Sensor signal valid - loss of signal
3 2 SR Sensor signal valid - loss of signal
4 2 SAL Sensor signal valid - loss of signal
5 2 SAR Sensor signal valid - loss of signal
2 3 SL Sensor signal valid – noisy
3 3 SR Sensor signal valid – noisy
4 3 SAL Sensor signal valid – noisy
5 3 SAR Sensor signal valid – noisy
2 4 SL Sensor shorted or open
3 4 SR Sensor shorted or open
4 4 SAL Sensor shorted or open
5 4 SAR Sensor shorted or open
2 5 SL Tire diameter out of range
3 5 SR Tire diameter out of range
4 5 SAL Tire diameter out of range
5 5 SAR Tire diameter out of range
Sensors
Modulators
ABS Control Mode
Diagnostic Trouble Codes
J1587
Description
WHEEL SPEED SENSORS (WSS)
Display Odometer Mileage
To display the trailer odometer mileage, apply ignition
power and depress/release the brake pedal seven (7) times
within 15 seconds. Following activation, there will be a
five (5)-second delay followed by a blink code display of
the odometer information (x1000).
Example: 152,431 miles will be displayed as: one (1) blink,
(pause), five (5) blinks, (pause), two (2) blinks.
Zeros will be displayed by the ABS indicator lamp strobing
twice.
Odometer mileage cannot be altered with blink code
diagnostics. Complete odometer information can be
retrieved using a diagnostic tool.
Resetting ABS Configuration
To reset the ABS configuration to the default configuration,
apply ignition power and depress/release the brake pedal
eight (8) times within 15 seconds. Following activation,
the Bendix
default ABS configuration (2S/1M), and will self-configure
the next time the trailer receives power.
J1587
(SID) (FMI)
1 0 • ABS system fully operational – no DTCs detected
1 0
2 0
3 0
4 0
1 1
2 1
3 1
4 1
1 2
2 2
3 2
4 2
4 or
1
5
4 or
2
5
4 or
3
5
4 or
4
5
1 13 • Verify correct tire size as desired.
Verify proper tire inflation.
•
2 13
• Verify correct number of exciter ring teeth.
3 13
• Verify that the Electronic Control Unit (ECU) has the proper
4 13
tire size settings.
ABS configuration will reset to the
TABS-6
® ™
(DTCs)
Repair Information
Dynamic Wheel Speed Sensor DTC.
Go to Section G, on Page 31.
Static Wheel Speed Sensor DTC.
Go to Section G, on Page 31.
11