AEL ACP Installation & Maintenance Instructions

INSTALLATION & MAINTENANCE INSTRUCTIONS
ENSURE UNIT IS PROPERLY GROUNDED AND DISCONNECT POWER DURING INSTALLATION AND
BEFORE SERVICING TO AVOID THE RISK OF SEVERE OR FATAL ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL
AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION, CONSULT LOCAL CODE AUTHORITY
INSTALLATION INSTALLATION
YOKE MOUNT: YOKE MOUNT:
THE YOKE HAS 3 MOUNTING HOLES, THE YOKE HAS 3 MOUNTING HOLES,
ONE FOR A 3/4" BOLT AND TWO FOR 3/8" BOLTS. ONE FOR A 3/4" BOLT AND TWO FOR 3/8" BOLTS.
MOUNTING ADAPTORS ARE AVAILABLE TO ALLOW FOR MOUNTING ADAPTORS ARE AVAILABLE TO ALLOW FOR
HORIZONTAL ADJUSTMENT ON POLE TOPS, CROSS HORIZONTAL ADJUSTMENT ON POLE TOPS, CROSS
ARMS, ETC. HORIZONTAL ADJUSTMENT MUST BE ARMS, ETC. HORIZONTAL ADJUSTMENT MUST BE
DETERMINED BEFORE MOUNTING THE YOKE TO THE DETERMINED BEFORE MOUNTING THE YOKE TO THE
CROSSARM IF THE ACP FLOOD IS BEING MOUNTED CROSSARM IF THE ACP FLOOD IS BEING MOUNTED
DIRECTLY TO A CROSSARM WITHOUT THOSE OPTIONAL DIRECTLY TO A CROSSARM WITHOUT THOSE OPTIONAL
FITTERS. FITTERS.
TENON MOUNT: TENON MOUNT:
THE COMPACT FLOOD WITH OPTIONAL THE COMPACT FLOOD WITH OPTIONAL
TENON MOUNT CAN BE MOUNTED TO A 2" OR 2 1/2" TENON MOUNT CAN BE MOUNTED TO A 2" OR 2 1/2"
PIPE TENON. TIGHTEN ALL FOUR SET SCREWS EQUALLY PIPE TENON. TIGHTEN ALL FOUR SET SCREWS EQUALLY
TO A MAXIMUM OF 350 INCH LBS., THEN TIGHTEN EACH TO A MAXIMUM OF 350 INCH LBS., THEN TIGHTEN EACH
LOCK NUT TO A MAXIMUM OF 350 INCH LBS. TO LOCK NUT TO A MAXIMUM OF 350 INCH LBS. TO
SECURELY ATTACH FIXTURE TO TENON TOP. SECURELY ATTACH FIXTURE TO TENON TOP.
ADJUSTMENT: ADJUSTMENT:
YOKE MOUNT: YOKE MOUNT:
INDEX MARKS ARE INDICATED ON INDEX MARKS ARE INDICATED ON
EACH SIDE OF YOKE FOR DETERMINING DESIRED EACH SIDE OF YOKE FOR DETERMINING DESIRED
MOUNTING ANGLES. THE BOLTS ON EACH SIDE OF MOUNTING ANGLES. THE BOLTS ON EACH SIDE OF
YOKE NEED TO BE LOOSENED, VERTICAL ADJUST- YOKE NEED TO BE LOOSENED, VERTICAL ADJUST-
MENT MADE AND THEN BOTH BOLTS RETIGHTENED MENT MADE AND THEN BOTH BOLTS RETIGHTENED
TO A MAXIMUM OF 400 INCH LBS. TO A MAXIMUM OF 400 INCH LBS.
TENON MOUNT: TENON MOUNT:
THE SET SCREWS AND LOCK NUTS THE SET SCREWS AND LOCK NUTS
SHOULD BE LOOSENED AND HORIZONTAL ADJUSTMENT SHOULD BE LOOSENED AND HORIZONTAL ADJUSTMENT
MADE. SET SCREWS SHOULD THEN BE RETIGHTENED MADE. SET SCREWS SHOULD THEN BE RETIGHTENED
AND LOCK NUTS RETIGHTENED. INDEX MARKS ARE AND LOCK NUTS RETIGHTENED. INDEX MARKS ARE
INDICATED ON TENON FOR DETERMINING DESIRED INDICATED ON TENON FOR DETERMINING DESIRED
ANGLE. LOOSEN BOLT IN CENTER OF TENON MOUNTED ANGLE. LOOSEN BOLT IN CENTER OF TENON MOUNTED
ACP COMPACT FLOOD TO DESIRED ANGLE AND ACP COMPACT FLOOD TO DESIRED ANGLE AND
RETIGHTEN BOLT TO SECURE TENON MOUNT.TIGHTEN RETIGHTEN BOLT TO SECURE TENON MOUNT.TIGHTEN
BOLT TO A MAXIMUM OF 400 INCH ILBS. BOLT TO A MAXIMUM OF 400 INCH ILBS.
BREATHING HOLES BREATHING HOLES
THIS UNIT HAS BEEN DESIGNED WITH THREE THIS UNIT HAS BEEN DESIGNED WITH THREE
BREATHING HOLES. TWO HOLES IN THE WIRING BREATHING HOLES. TWO HOLES IN THE WIRING
COMPARTMENT AREA AND 1 HOLES IN THE BEZEL. ALL COMPARTMENT AREA AND 1 HOLES IN THE BEZEL. ALL
HOLES ARE PLUGGED WITH A SCREW. ONLY IF THE UNIT HOLES ARE PLUGGED WITH A SCREW. ONLY IF THE UNIT
IS YOKE MOUNT AND HAS NO PHOTOCONTROL IS YOKE MOUNT AND HAS NO PHOTOCONTROL
RECEPTACLE MUST ANY ACTION BE TAKEN. THE SCREW RECEPTACLE MUST ANY ACTION BE TAKEN. THE SCREW
IN THE BEZEL IS TO BE REMOVED ONLY IF THE UNIT IS IN THE BEZEL IS TO BE REMOVED ONLY IF THE UNIT IS
FACING DOWN. ONE OF THE TWO SCREWS IN THE FACING DOWN. ONE OF THE TWO SCREWS IN THE
WIRING COMPARTMENT IS TO BE REMOVED ONLY IF THE WIRING COMPARTMENT IS TO BE REMOVED ONLY IF THE
UNIT IS FACING UP. CHOOSE THE SCREW THAT IS NOT UNIT IS FACING UP. CHOOSE THE SCREW THAT IS NOT
HOLDING DOWN THE CAPACITOR BRACKET. HOLDING DOWN THE CAPACITOR BRACKET.
DRAWING NO. A71218 REV B
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
ACP COMPACT FLOODLIGHT
WARNING
!
!
WIRING WIRING
COMPARTMENT COMPARTMENT
(FRONT)
©2007 ACUITY LIGHTING GROUP, INC.
WARNING
CAUTION
!
CLAMPING CLAMPING
BOLTS (2) BOLTS (2)
POWER CORD POWER CORD
ENTRY ENTRY
REMOVABLE REMOVABLE
PLUG PLUG
SCREWS (3) SCREWS (3)
CLOSURE CLOSURE
SCREWS (2) SCREWS (2)
2
1
YOKE
MOUNTING
HOLES
PART NUMBER 057-70-71218