Advertisement
5. COOL AIR FAN
The heater may also be used as a cool air fan, as follows:
5.1.
Remove the gas supply hose and plug the heater into the mains electrical power supply.
5.2.
Switch on the fan. The unit will now blow out cool air only.
6.
MAINTENANCE
Maintenance and repair must be carried out by trained/authorised personnel only. Contact your dealer for your nearest service agent.
! WARNING! Before commencing service or maintenance disconnect the unit from the electrical power and the gas supply. Use authorised parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
6.1.
Check the gas supply hose condition and change if necessary.
6.2.
Check the starting electrode gap (fig.5).
6.3.
Check the ignition unit, safety thermostat, and thermocouple condition
and ensure that they are clean.
Caution: Wear safety goggles to perform this operation.
%
6.4.
Clean inside the heater unit and the fan blade with compressed air.
7. TROUBLESHOOTING
PROBLEM
The fan motor
does not work
The ignitor does
not spark
No gas flow
to the burner
The burner starts, but it
stops as the gas valve
is released.
The heater stops
during operation.
8.
DECLARATION OF CONFORMITY
Declaration of Conformity
Propane Heaters:
LP351, LP351S, LP451, LP451S, LP601, LP601S
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
93/68/EEC CE Marking Directive
Gas Appliances (Safety) Regulations 1992
98/37/EC Machinery Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this equipment.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
POSSIBLE CAUSE
1.
There is no electrical supply.
2.
The motor has locked.
1.
Electrode has the wrong gap.
2.
Faulty connection.
1.
The cylinder gas tap is closed.
2.
The cylinder is empty.
3.
Nozzle is blocked.
1.
The thermocouple is not
warm enough.
2.
The safety override has
activated because the fan
does not work.
1.
Excessive gas supply.
2.
Insufficient air flow.
3.
Insufficient gas due to
ice formation on the cylinder.
We, the sole importer into the UK, declare that the products listed here are in conformity with the following standards and directives.
The construction files for these products are held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack Sealey Ltd.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
fig.5
5mm
SOLUTION
1.
Check mains power supply, wire, plug, fuse.
2.
Unlock the motor with appropriate tool.
1.
Check and reset the electrode to the correct position (fig.5).
2.
Check and connect correctly the ignitor and the electrode.
1.
Open the gas tap.
2.
Replace the cylinder.
3.
Remove and clean the nozzle, check for leaks by using a
foamy soap solution or leak detector spray. DO NOT USE
FLAME to find leak.
1.
Repeat the starting operation keeping the button
pushed for a longer time
2.
See above "Motor does not work"
1.
Check the pressure reducer, and replace if necessary.
2.
Check that the motor is working correctly.
3.
Check and if necessary use a larger gas cylinder or
multiple cylinders connected parallel.
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
01284 757500
01284 703534
8th June 2006
www.sealey.co.uk
Web
sales@sealey.co.uk
email
LP351, LP351S, LP451, LP451S, LP601, LP601S - 2 - 080606
Advertisement
