1UP USA QUIK RACK SINGLE Manual

Advertisement

Quick Links

Parts List:

1)
1.25'' Hitch
2)
Left 1.25'' Side Plate
3)
Left Pivot Beam
4)
Cross Bar
5)
Black Bar
6)
Right 1.25" Side Plate
7)
Gold Bar Knob
8)
Gold Bar
9)
Right Pivot Beam
10)
Tap Plate

In The Box:

1UP USA Quik Rack Single
2 Gold Security Wrenches
Velcro Strap
Black ¼'' Hex Wrench

Product Notes:

Fits 16''-29'' wheels, up to 3.1'' wide. For wider tires, use a Fat Bike Spacer Kit (sold separately).
Rated to hold a bike up to 50 lb per bike spot.
With the addition of two Add-Ons (sold separately), this rack can hold a maximum of three bikes.
1.25" - 2" QUIK RACK SINGLE
11) Passenger Side Tray
12) Bent Arm
13) 19" Strap
14) Glide Bar
15) Red Lever
16) 15° Plate
17) Blue Lever
18) Driver Side Tray
19) 2" Hitch Adapter

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QUIK RACK SINGLE and is the answer not in the manual?

Questions and answers

Summary of Contents for 1UP USA QUIK RACK SINGLE

  • Page 1 1.25” - 2” QUIK RACK SINGLE Parts List: 1.25’’ Hitch 11) Passenger Side Tray Left 1.25’’ Side Plate 12) Bent Arm Left Pivot Beam 13) 19” Strap Cross Bar 14) Glide Bar Black Bar 15) Red Lever Right 1.25” Side Plate 16) 15°...
  • Page 2 Step 1: • Remove rack from box. • Unfold hitch parallel with the trays. • Remove all cardboard supports. • Remove plastic wrap around hitch. Step 2: • Position rack with hitch bar facing upwards and place on a stable nonabrasive surface. •...
  • Page 3 Step 3: • Rotate trays outward 90° into loading positon. • Rotate Blue Levers back into original locking positon. • Ensure Blue Levers are in position at all times when using the Rack. Step 4: • Insert Rack to desired depth in the receiver. The ball must be inserted a minimum of 2’’. •...
  • Page 4 Step 5: • Pivot the Rack into the vertical position by pulling the Black Bar back and lifting upward on the Tap Plate. Tap Plate Note: See Rack Positions for more information. Step 6: • Tighten Security Bolt firmly with the gold Security Wrench provided. •...
  • Page 5 Pivoting the Rack • Pull the Black Bar out away from the hitch while lifting up on Tap Plate. • Rotate rack towards desired position and release black bar. Ensure it is fully engaged in the slots. • Once positioned, tighten the Gold Bar Knob to keep the Black Bar in place. Note: In the rear access position, the Black Bar will not lock into place.
  • Page 6 Loading Bikes • Lift the Red Lever up parallel with the Glide Bar while pulling up on the Bent Arm. Do this on both the driver and passenger side. Note: Do not move the Bent Arms up without lifting the Red Lever. •...
  • Page 7 Wheel Settings • The Rack is set to hold 26’’, 27.5’’, 29’’, or 700-C wheels. If bike tires are smaller, see instructions below to adjust spools accordingly. 24’’ 20’’ 16’’ With a ½’’ wrench, remove the hex nut and washer. Slide the bolt out of the spools and re-assemble the spools in the desired wheel position, firmly tightening the hex nut.

Table of Contents