AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc. for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for use with recorder, router, software and camera products. Because it matters.™ is a trademark of AJA Video Systems, Inc.
Chapter 1 – Introduction Overview AJA 10 GigE IP Mini-Converters are designed for point of use applications for encoding, transport, reception and decoding of IP based video sources. Rugged, compact and fanless, the 10 GigE IP Mini-Converters provide the bridge between...
NOTE: The System Modes are available only for the IPR units; they are not found on the IPT units. NOTE: Like the IPR-10G2-HDMI and IPR-10G2-SDI, the IPR-10G-HDMI has the System Modes. However, since the 10G model does not have dual stream redundancy, it does not offer the highest level of packet-level protection.
• NMOS Rx discovery and control according to standards IS-04 v1.2 and IS-05 v1.0 • Ember+ control (no discovery, control only) • AJA REST API control (discovery via SSDP or MDNS) • 1x 3G-SDI Input • 1x 3G-SDI Loop Out •...
• 1x mini-USB port for initial network configuration with AJA eMini-Setup software (alternative setup method) • 5-year international warranty and support IPT-10G2-HDMI • SMPTE ST 2110 audio, video transmitter including support for ST 2022-7 • Essence support: SMPTE 2110-10, 2110-20, 2110-30 •...
• 1x BNC Reference for analog/tri-level reference input, allowing baseband output to be locked to the facility baseband clock (instead of PTP) • 1x mini-USB port for initial network configuration with AJA eMini-Setup software (alternative setup method) • 5-year international warranty and support IPR-10G2-HDMI •...
• Full 10-bit pixel processing pipeline (except for UHD p50) • Embedded HDMI audio output (up to eight channels) • 2x RCA analog audio output • 1x mini-USB port for initial network configuration with AJA eMini-Setup software (alternative setup method) • 5-year international warranty and support Abbreviated Feature Comparison Chart for v2.2...
Lock LED Link/Act LED 1 Reference Out BNC SFP+ Cage for 10 Gbps Ethernet USB Port SFP+ Cage for 10 Gbps Ethernet +5-16 VDC Link/Act Power Input LED 2 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 11 www.aja.com...
Page 12
Figure 3. Example Workflow Diagram for the IPT-10G2-HDMI HD Camera or Other HDMI Source* Ref In HD HDMI Media Server Remote Monitor IPR-10G2-HDMI HDMI 10 GigE 1x HDMI Input/Output HD (up to 60p) Input/Output Black Burst/ Redundant IP feeds Tri-level sync...
Page 13
Connector 2 Link/Act LED 1 Analog/Tri-Level SFP+ Cage for Reference Input BNC 10 Gbps Ethernet USB Port SFP+ Cage for 10 Gbps Ethernet +5-16 VDC Link/Act Power Input LED 2 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 13 www.aja.com...
Page 14
Figure 7. Example Workflow Diagram for the IPR-10G2-HDMI HDMI Recorder/Player or other HDMI destination Media Server NOTE: HDMI monitors won’t re- quire reference 10 GigE 1x HDMI Input/Output PTP Generator Black Burst or Tri-level sync generator* 10 GigE Switch UltraHD (up to 50p)
Page 15
Figure 10. IPR-10G-HDMI Connections 2 Channel Unbalanced Analog Audio Output Control (RCA Jacks) Ready LED Output HDMI Connector Link/Act SFP+ Cage Port for 10 Gbps Ethernet +5-20 VDC Power Lock LED Input 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 15 www.aja.com...
RCA Analog Audio Input USB Port (connect to PC or Mac) For initial setup of network interfaces Figure 12. IPR-10G2-SDI/HDMI Simplified Block Diagram IPR-10G2-SDI / IPR-10G2-HDMI SDI Out 1 with 8 Ch. Reference Transmitter of embedded audio Input Analog/tri-level reference input SDI Out 2 with 8 Ch.
Frequently Asked Questions To access responses to freqently asked questions about the 10 GigE IP Mini-Converters, please use the following links: • https://www.aja.com/products/ipt-10g2-sdi#support • https://www.aja.com/products/ipt-10g2-hdmi#support • https://www.aja.com/products/ipr-10g2-sdi#support • https://www.aja.com/products/ipr-10g2-hdmi#support • https://www.aja.com/products/ipr-10g-hdmi#support 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 17 www.aja.com...
NOTE: Chrome and Firefox are the preferred web browsers for control on Windows. Safari is the preferred web browser for control on macOS. Other web browsers may work, but AJA cannot guarantee consistent operation for all web browsers or web browser versions.
NOTE: DHCP is enabled by default, and if the device is connected to a DHCP server the IP address field will populate. 6. Enter the IP address into a browser window. The web UI for your AJA device will display.
Media LAN 2 and connect the unit’s inputs and outputs. REST API Documentation AJA’s REST automation API provides a platform from which you can issue commands to an AJA device’s internal web server, allowing remote systems the ability to control AJA embedded or networked devices. With this control framework, you can build integration and automation scripts, using any scripting language, allowing you to take full advantage of the device’s functionality.
Subsequently, that device can then be reconfigured over that network, using its IP address and built-in web server. NOTE: The eMini-Setup application is only used to setup selected Ethernet capable AJA devices, and cannot be used to connect to or setup other AJA Mini-Converters.
When finished, an AJA eMini-Setup shortcut will be installed on the desktop, and you will be able to locate the eMini-Setup application in the AJA folder in the Programs listing. NOTE: If the eMini-Setup application already exists on the PC, a different Setup Wizard appears.
Applications folder. Running eMini-Setup Connect your Ethernet capable AJA device to the PC or Mac via the supplied USB cable, and then connect the external power supply (supplied) to that AJA device. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 23...
PC Startup To run eMini-Setup on a PC, double-click on the AJA eMini-Setup icon on your desktop, or open the AJA folder in the program list and click on the AJA eMini- Setup application located inside the eMini-Setup folder. Figure 19. Launching eMini-Setup on a PC...
Sn - This is the factory set unique serial number of your AJA device. If you ever call AJA Support for service, you may be asked for this number. A status field at the bottom of the screen shows if the eMini-Setup application is connected and communicating with an AJA device.
Figure 22. eMini-Setup Media LAN 1 Tab Screen Use this Media LAN 1 tab to change the corresponding media network setup on the connected AJA device. You must click the Apply button to initiate any network configuration changes. IP Address Type - Choose from DHCP or Static IP Address.
Figure 23. eMini-Setup Media LAN 2 Tab Screen Use this Media LAN 2 tab to change the corresponding media network setup on the connected AJA device. You must click the Apply button to initiate any network configuration changes. IP Address Type - Choose from DHCP or Static IP Address.
4. Click the Update tab. Click the Browse button. Navigate to the firmware (.ajas extension), open it, and confirm the update. Progress will be shown via the “Progress” bar. 5. After the update, the AJA device must be rebooted by clicking on the Reboot button in the prompt window. See also: "Firmware Screen"...
AJA Support for service or technical support. System Name - This field allows you to give your AJA device a unique name. This can be useful if you have several attached to a Mac/PC via USB so you can distinguish between them easily.
Media LAN connection for the IPR-10G-HDMI. NOTE: Safari is the preferred web browser for control on the Mac, and additionally Chrome and Firefox on Windows. Other web browsers may work, but AJA cannot guarantee consistent operation for all web browsers or web browser versions.
Ethernet LEDs of that device at a 1 second rate. Parameters and Information The rest of the screen displays all the parameter selections and information available for the selected IP Mini-Converter screen. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 31 www.aja.com...
Page 32
• For values with sliders, fine control is achieved using the arrow keys on the keyboard to move the slider the minimum amount. The numeric value can also be clicked on to enter a specific value. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 32 www.aja.com...
The IPT-10G2-SDI Status screen reports the current status and settings for: • Stream Status • PTP Clock Status • Network Status • NMOS Status • Firmware Status Each group of parameters can be expanded or collapsed. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 33 www.aja.com...
Page 34
Figure 28. IPT-10G2-SDI Status Screen 2 of 2 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 34 www.aja.com...
IPR-10G2-HDMI Figure 29. IPR-10G2-HDMI Status Screen 1 of 2 The IPR-10G2-HDMI Status screen reports the current status and settings for: • Input Status • Video Clock Status • Network Status • NMOS Status • Firmware Status Each group of parameters can be expanded or collapsed.
Figure 30. IPR-10G2-HDMI Status Screen 2 of 2 Config Screen This section describes the Config Screen for the IPT-10G2-SDI followed by the Config Screen for the IPR-10G2-HDMI. IPT-10G2-SDI The IPT-10G2-SDI Config Screen, shown in three parts, has the parameters required for the general operation of the IPT-10G2 units.
Page 37
Enable or disable network discovery using Universal Plug and Play. IGMP Version Select the Internet Group Management Protocol Version. AJA supports IGMP v2 and v3. NOTE: It is important to know which version of IGMP is in use on your network.
Page 38
Enter the UDP destination port of the video packets. Video Source Port 1 Enter the UDP source port of the video packets. Audio Dest IP Address 1 Enter the destination IP address of the audio packets. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 38 www.aja.com...
Page 39
Enter the UDP source port of the video packets. Audio Dest IP Address 2 Enter the destination IP address of the audio packets. Audio Destination Port 2 Enter the UDP destination port of the audio packets. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 39 www.aja.com...
Page 40
Select the vertical reference offset in pixels (range -1125 lines to +1125 lines). You can use either the slider control on the web UI or the left/down and right/up arrow keys on your keyboard. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 40 www.aja.com...
Page 41
Enter a value to specify the video payload type. Audio Payload Type Enter a value to specify the audio payload type. NMOS Enable or disable NMOS network discovery for the device. NMOS is on by default. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 41 www.aja.com...
Ember+ Enable or disable Ember+ network discovery for the device. IPR-10G2-HDMI The IPR-10G2-HDMI Config Screen, shown in three parts, has the parameters required for the general operation of the IPR-10G2 units. Figure 34. IPR-10G2-HDMI Config Screen 1 of 3 Menu...
Page 43
NOTE: The System Modes are available only for the IPR units; they are not found on the IPT units. NOTE: Like the IPR-10G2-HDMI and IPR-10G2-SDI, the IPR-10G-HDMI has the System Modes. However, since the 10G model does not have dual stream redundancy, it does not offer the highest level of packet-level protection.
Page 44
Unlike the five pre-built System Modes just described, each of which are "safe," the Advanced Mode, described below, does not guard against a user applying contradictory settings that could provide unpredictable results. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 44 www.aja.com...
Page 45
PTP, such as if it is from an independent sync generator, you will need to use Frame Sync in order to prevent output glitches. New Reference Input support for IPR-10G2-HDMI and IPR-10G2-SDI provides users with the ability to lock the local baseband output to the timing of the baseband environment at the destination.
Page 46
PTP Grand Master Capable NOTE: Applicable only if PTP is selected for Video Output Clock Selection. For local demonstration purposes only, the IPR-10G2-HDMI and IPR-10G2-SDI can act as a grandmaster in network environments where there is not one already present, such as during basic testing, setting up a PoC or demonstration.
Page 47
Figure 35. IPR-10G2-HDMI Config Screen 2 of 3 IPR-10G2-TLK-ENG007 Menu Connection Status Serial Number Config ENG007 Video Input Format Presets Software Version 1 9 2 0 x 1 0 0 p 5 9 . 9 4 Input Stream Selection 2.2.0.37d...
Page 48
ST 2110 stream. In unicast mode, this is the unicast IP address of the media port on the receiver. The Video Destination Address is almost always required on a receiver (IPR-10G2-HDMI, IPR-10G-HDMI, IPR-10G2-SDI). Additionally, the destination UDP port of the stream may also be specified by appending it with a colon to the destination address.
Page 49
Figure 36. IPR-10G2-HDMI Config Screen 3 of 3 IPR-10G2-TLK-ENG007 Menu Connection Status Serial Number Config ENG007 Audio Destination Address Presets Software Version 239.112.0.30 Input Stream Selection 2.2.0.37d Network Connection Status Firmware Connected Audio Source Address Alarms - Ignore - Network...
Page 50
RCA audio outputs. Choose one of the following: • Channels 1 & 2 • Channels 3 & 4 • Channels 5 & 6 • Channels 7 & 8 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 50 www.aja.com...
Enable or disable network discovery for the device. Enable/Disable Video Enable or disable video for the device. Enable/Disable Audio Enable or disable audio for the device. Presets Screen Figure 37. IPR-10G2-HDMI Presets Screen Menu IPR-10G2-TLK-ENG007 Connection Status Serial Number Factory Reset...
Erase Presets 1–20 (All) - Erase All erases all data from all the presets. A dialog box warns you that the operation will erase all 20 current presets. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 52 www.aja.com...
Network Screen Use the Network Configuration Control Tab to configure or modify settings for the Control LAN Ethernet port. Figure 38. IPR-10G2-HDMI Network Configuration Control Tab IPR-10G2-TLK-ENG007 Menu Connection Status Serial Number Factory Reset Factory Settings Reset Config ENG007 Presets...
Page 54
Figure 39. IPR-10G2-HDMI Network Configuration Media 1 Tab Menu IPR-10G2-TLK-ENG007 Connection Status Serial Number Factory Reset Factory Settings Reset Config ENG007 Software Version Presets Preset #1 Preset 1 Save Recall Export Import Erase 2.2.0.37d Network Connection Status Firmware Preset #2...
Page 55
MAC Address - Reports the connected IP Mini-Converter's Media Access Control Address. Link State - Reports the current status of the Ethernet connection. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 55 www.aja.com...
Use the following to perform a reboot of your IPR-10G2-HDMI: Reboot CY-IPR10G2-HDMI GC-IPT-10G2-SDI-E… Use the following to abort an update of your IPR-10G2-HDMI during the upload stage only: Abort Update IPR-10G-HDMI-EN… For latest firmware point your browser to: IPR-10G2-HDMI Support Page IPR-10G2-HDMI-EN…...
Page 57
Installing Updated Firmware" on page 56. Following a successful firmware update and reboot, the message "None" displays under the Alarms heading. Figure 44. The alarm message after a successful firmware update 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 57 www.aja.com...
• Up to 8 channels audio, 24-bit per channel, 48 kHz synchronous • 1 ms or 125 µs packet interval • SMPTE ST 2022-7 dual stream input for hitless switching 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 58 www.aja.com...
Page 59
• Web and REST clients supported for remote network setup and configuration • 1x USB 2.0 Mini-B connector • AJA eMini-Setup supported for network setup and configuration via local desktop computer • Web and REST configuration is also supported in-band over media ports Size (w x d x h) •...
• 1 ms or 125 µs packet interval • SMPTE ST 2022-7 dual stream input for hitless switching Reference • 1x BNC • Reference Out connector generates an analog/tri-level reference output synchronized to the PTP clock 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 60 www.aja.com...
• Web and REST clients supported for remote network setup and configuration • 1x USB 2.0 Mini-B connector • AJA eMini-Setup supported for network setup and configuration via local desktop computer • Web and REST configuration is also supported in-band over media ports Size (w x d x h) •...
Page 62
• NMOS Rx discovery and control according to standards IS-04 v1.2 and IS-05 v1.0 • Ember+ control (no discovery, control only) • AJA REST API control (discovery via SSDP or MDNS) • Supported over dedicated management Ethernet port and in-band over media ports Media Transport Interfaces •...
• Web and REST clients supported for remote network setup and configuration • 1x USB 2.0 Mini-B connector • AJA eMini-Setup supported for network setup and configuration via local desktop computer • Web and REST configuration is also supported in-band over media ports Size (w x d x h) •...
Page 64
• Levels at -10 dBu (nominal) Reference* • 1x BNC • Analog/tri-level reference input • Allows baseband output of IPR-10G2-HDMI to be locked to the facility baseband clock *Reference functionality support is up to 1080p 60 (UltraHD is not supported) IP Clock •...
• Web and REST clients supported for remote network setup and configuration • 1x USB 2.0 Mini-B connector • AJA eMini-Setup supported for network setup and configuration via local desktop computer • Web and REST configuration is also supported in-band over media ports Size (w x d x h) •...
Page 66
• Web and REST clients supported • 1x USB 2.0 Mini-B connector • AJA eMini-Setup of network parameters via local desktop computer Size (w x d x h) • 5.53" x 4.48" x 0.954" (140.46 x 113.79 x 24.23 mm) Weight •...
AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA, FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, ICELAND, IRELAND, ITALY, LATVIA, LICHTENSTEIN, LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, NORWAY, POLAND, PORTUGAL, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, SWITZERLAND, UNITED KINGDOM 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 68 www.aja.com...
Page 69
As an electromagnetic wave equipment for office use (Class A), (Broadcasting Communication this equipment is intended to use in other than home area. Equipment for Office Use) Sellers or users need to take note of this. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 69 www.aja.com...
Page 70
Aviso! Leia e siga todos os avisos e instruções assinalados no produto ou incluídos na documentação. Avviso! Leggere e seguire tutti gli avvisi e le istruzioni presenti sul prodotto o inclusi nella documentazione. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 70 www.aja.com...
Page 71
(incluindo amplificadores) que produzam calor. Avviso! Non installare vicino a fonti di calore come termosifoni, diffusori di aria calda, stufe o altri apparecchi (amplificatori compresi) che emettono calore 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 71 www.aja.com...
Page 72
Aviso! Dado que a ficha principal é utilizada como a desconexão para o dispositivo, esta deve manter-se prontamente acessível e funcional. Avviso! Poiché il cavo di alimentazione viene usato come dispositivo di sconnessione, deve rimane prontamente accessibile e operabile. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 72 www.aja.com...
Page 73
Aviso! Desconecte este dispositivo da tomada durante trovoadas ou quando não é utilizado durante longos períodos de tempo. Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal produttore, quali il treppiedi e l'esoscheletro. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 73 www.aja.com...
Page 74
Advertência! Não abra o chassi. Não há internamente nenhuma peça que permita manutenção pelo usuário. Abrir o chassi anula a garantia, a menos que a abertura seja realizada por uma central de serviços da AJA ou por um local autorizado. Avvertenza! Non aprire lo chassis. All’interno non ci sono parti riparabili dall’utente.
Page 75
¡Advertencia! Utilice solamente los accesorios y conexiones especificados y/o vendidos por el fabricante. Aviso! Utilize apenas equipamentos/acessórios especificados e/ou vendidos pelo fabricante. Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal produttore. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 75 www.aja.com...
No amendment to or modification of this warranty will be binding unless in writing and signed by AJA Video. The laws of the State of California, USA will govern this warranty and any dispute arising from it. Any translation of this 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 76...
Page 77
This limited warranty gives you specific legal rights and you may have other rights that vary from jurisdiction to jurisdiction, some of which are noted above. 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 77 www.aja.com...
Index eMini-Setup on Mac 24 Erasing 53 eMini-Setup on Windows 23 Exporting 53 AJA Support 2 Of Firmware Using eMini-Setup File Name Suffix 53 Audio Importing 53 RCA Analog Audio Output 51 Overview 19 Recalling Authentication 31 I/O Connections 11...
Page 79
Web Browser Accessing Unit Through Its IP Address 22 Loading Firmware 22 Preferred 18 System Requirements 18 Web Server Access Password 53 Built In Unit's Internal 18 workflow diagrams 11 10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.2r1 79 www.aja.com...
Need help?
Do you have a question about the IPR-10G2-HDMI and is the answer not in the manual?
Questions and answers