Related Manuals for First Choice ESCHER M40
Summary of Contents for First Choice ESCHER M40
- Page 1 SPARE PARTS DIAGRAM FOR Mixer First Choice Group Blakeney Way, Kingswood Lakeside Cannock, Staffs, WS11 8LD TEL: 01543 577778 FAX: 01543504141 Email: enquires@firstchoice-cs.co.uk Web: www.firstchoice-cs.co.uk...
-
Page 2: Table Of Contents
ESCHER MIXERS srl Via Lago di Vico, 37 tel. +039 0445 576692 36015 SCHIO (VI) - ITALY fax +039 0445 577280 FOREWORD User, aim and use of the manual……………3 USE AND MAINTENANCE MANUAL Machine marking data……………………..3 SECTION A General information SPARE PARTS Warnings ………………………………3... -
Page 3: Foreword
FOREWORD • The machine must not be tampered with, altered or modified, even partially, and in particular, the protection guards must not be removed. • The machine must not be used in conditions or for use other than those USER, AIM AND USE OF MANUAL specified in this manual. -
Page 4: Reference Standards
The model of the machine described in this manual is in compliance with Directive 89/392/EEC, with its amending directives and with reference to the OPERATORS following standards: • The machine has been designed and constructed for professional use. Therefore: UNI EN 292-1, UNI EN 292-2. Basic concepts for machine safety and •... - Page 5 LIFTING THE PACKAGED MACHINE The machine is transported on a wooden pallet A , secured by a cross bar C, and fastened to the pallet by means of two threaded rods B. To lift by means of a pallet transfer unit or lift truck, insert the forks in the positions indicated in the figure.
-
Page 6: Installation - Preparation For Commissioning
MOVING THE MACHINE BY HAND The machine may need to be moved in order to clean the area under it. To move the machine : Tighten the threaded rod of the foot C which when it retracts allows the front pivoting wheel B to touch the floor. The other two points of support are the two rear fixed wheels A . -
Page 7: B.5 Control Panel
B.5 CONTROL PANEL S T A R T N U D G E Timer for first spiral tool speed Timer for second spiral tool speed Power indicator When the pointer is below zero, (display unlit), the timed shutoff When lit, it indicates that the electrical board is powered. function is deactivated. -
Page 8: Section C
SECTION C: INFORMATION REGARDING MAINTENANCE • Tighten the two nuts C (in order to loosen the belts) and remove them. MAINTENANCE ORDINARY: Includes: • Daily cleaning • Checking the belt tension ( monthly) See chapter C.2 for operative methods. EXTRAORDINARY •... -
Page 9: Model M40 Premium - M60 Premium
Tighten the four screws A which secure the motor support. Replace belts H and then belts G. Reconnect the connector E. • Reposition the upper transmission plate L and secure it by means of Put the protection guard T back into its correct position with regard to the four screws I . -
Page 10: Adjusting Belt Tension For Bowl Rotation
ADJUSTING THE BELT TENSION FOR BOWL ROTATION Bowl shaft Transmis. belts ( tr.pulleys – bowl Motor belts ( motor– tr.pulleys The belt tension must be adjusted if, during a work cycle, the operator notices a slowing down in the rotation of the bowl. To increase the tension of the transmission belts C: Use a wrench to rotate nut A in a clockwise direction. -
Page 11: Wiring Diagram For Power Supply
TRANSMIS. BELT TENSION MACHINE BASE Trans. shaft MOTOR BELT Motor TENSION shaft WIRING DIAGRAM FOR POWER SUPPLY... -
Page 12: Wiring Diagram For Control Panel
WIRING DIAGRAM FOR CONTROL PANEL... -
Page 13: Wiring Diagram For Assembly
WIRING DIAGRAM FOR ASSEMBLY... -
Page 14: Spare Parts List For 415 V System
1 3 0 c m 35 cm 35 cm CONNECTOR J1 RTA SHEATH 13 8 Z1 Y1 X1 L3 L2 L1 Z Y X FU1 FU1 FU2 SPARE PARTS LIST FOR 400-415V 50-60 Hz SYSTEM... -
Page 15: Spare Parts List For Control Panel
DESCRIPTION MANUFACTURER CODE Q.TY M1 SPIRAL TOOL MOTOR 132 B14 4/8 poles 2.1/3,7 KW E00300 M2 BOWL MOTOR 80 B3 6 poles 0,55 KW E00000 QS1 MAIN SWITCH WITH HANDLE CONTROL ILME ZQE 323 RODE ILME ZR 3280 TC1 TRANSFORMER 150VA 0..230.420 0.24 CE KA1 RELAY FINDER... - Page 16 DESCRIPTION MANUFACTURER CODE Q.TY 24- POLE CONNECTOR P ILME CHO 24 24- POLE CONNECTOR M ILME CNM 24 EMERGENCY -STOP PUSH BUTTON CEMA P9MER4RN CEMA P9B01VN START PUSH BUTTON TELEMECANIQUE ZB5 AA3 TELEMECANIQUE ZB5 AZ101 PROTECTIVE PUSH BUTTON COVER TELEMECANIQUE JOG BOWL PUSH BUTTON TELEMECANIQUE ZB5 AA6...
-
Page 18: List
List 1: Head group of model M P O S . D E S C R I P T I O N Q t y C O D E B e l t S P Z 1 5 8 7 C01211 Motor pulley D11116... -
Page 20: List
List 2: Head group of model M PREMIUM POS. D E S C R I P T I O N CODE B e l t S P Z 1 5 8 7 C01211 Pulley 50 Hz D11119 Pulley 60 Hz D11120 Bearing 62206 2RS C00001... - Page 21 Table 3: Bowl group – exploded view...
- Page 22 Table 4: Machine structure – exploded view...
- Page 24 List 4: Machine structure POS. DESCRIPTION CODE B o d y D 0 3 0 0 0 F o o t C 0 1 0 0 0 W h e e l c l o s i n g c a s i n g D 0 8 2 0 0 C a s t e r C 0 1 4 0 0...