Advertisement
WARNING:
This product may represent a possible shock or fire
hazard if improperly installed or attached in any
way. Product should be installed in accordance
with the owner's manual, current electrical codes
and/or the current National Electric Code (NEC).
(1)
(2)
(5)
(3)
(4)
1. J-Box (not included)
11. Mounting Holes
2. Mounting Bar
12. Rubber Washers (2 pieces)
3. J-Box Screws (2 pieces)
13. Decorative Nuts (2 pieces)
4. Spacers (2 pieces)
14. LED Flood Lights
5. Mounting Gasket
15. Camera Lens and Photocell Sensor
6. Mounting Plate
16. Speaker
7. Terminal Block
17. Motion Sensor
8. Mounting Plate Screws (2 pieces)
18. Mic
9. Mounting Bar Screw (1 piece)
19. Indicator Light
10. Fixture Body
PARTS INCLUDED
(not drawn to scale)
TOOLS REQUIRED
(not included)
RESETTING UNIT & ACCESSING SD CARD
To access Reset Button and
RESET
microSD™ card, remove cover using
BUTTON
a small screwdriver (included).
To reset the unit, (unit must be
connected to power) press the
Reset Button for 15 seconds or
until you hear an audible tone.
To remove microSD card, push
card in with your finger and release.
Card will eject halfway.
microSD CARD
INCLUDES 2 EXTRA SCREWS
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
RISK OF ELECTRIC SHOCK:
TURN OFF THE MAIN POWER AT
THE CIRCUIT BREAKER BEFORE INSTALLING.
(6)
(10)
(14)
(7)
(8)
(9)
(11)
(12)
(13)
(18)
ADJUSTING FIXTURE
Bottom View
Top View
Adjust flood lights side to side
Adjust camera side to side
Top View
Side View
Adjust flood light carousel
Adjust flood lights and camera
side to side
up and down
PRE INSTALLATION
(6)
Remove the Mounting Plate
(6) by unscrewing and
removing the Decorative Nuts
(13) and Rubber Washers (12).
(8)
(12) (13)
(11)
EXTERNAL J BOX INSTALLATION
1. Turn main power Off at circuit breaker or fuse box.
2. Install Mounting Bar (2) to an
External J-Box (1) using provided
J-Box Screws (3). Add Spacer (4)
to eliminate gap between Mounting Bar
and Mounting Plate.
NOTE: Spacer (4) may or may not
be needed.
3. Extend and feed J-Box wires through openings
on Mounting Gasket (5) and Mounting Plate (6).
NOTE:
Tear away at perforation
on Mounting Gasket (5)
(19)
(15)
4. Secure Mounting Gasket (5)
and Mounting Plate (6) to
(16)
Mounting Bar (2) using Mounting Bar
Screw (9). Do not over-tighten.
(17)
5. Connect power supply wires
directly to Terminal Block (7).
Secure wires to Terminal Block
by using a small screwdriver.
See below.
CONNECT:
Black wire to"L" input.
Ground wire to "GND" input.
White wire to "N" input.
6. Position and align the Mounting Holes (11) on
Fixture Body (10) to the Mounting Plate Screws (8).
Secure Fixture Body (10) to Mounting Plate (6) using
Rubber Washers (12) and Decorative Nuts (13).
(10)
7. Turn power On at circuit breaker or fuse box. Turn On wall switch
if connected to one. Ensure lights work before proceeding to step 8.
8. Once fixture is tightly secured to J-Box, apply silicone sealant
around the base of the fixture to prevent moisture from reaching
the connections.
1. Turn main power Off at circuit breaker or fuse box.
(1)
(2)
(3)
2. Install Mounting Bar (2) to a Flush J-Box (1)
(4)
3. Extend and feed J-Box wires through openings
(6)
(5)
(4)
L
D
N
G
N
(2)
4. Secure Mounting Gasket (5) and
(6)
(9)
L
N
D
G
N
(6)
(5)
(7)
5. Connect power supply wires
DETAIL
N
GND
L
6. Position and align the Mounting Holes (11) on
(10)
(8)
(6)
(11)
(12)
(13)
7. Turn power On at circuit breaker or fuse box. Turn On wall switch
8. Once fixture is tightly secured to J-Box, apply silicone sealant
Continued
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
FLUSH J BOX INSTALLATION
(2)
(3)
(1)
using provided J-Box Screws (3). Add Spacer
(4) to eliminate gap between Mounting Bar
(4)
and Mounting Plate.
NOTE: Spacer (4) only needed if
J-Box is recessed too deep.
(5)
(6)
on Mounting Gasket (5) and Mounting Plate (6).
(4)
L
N
D
NOTE:
G
N
Do not tear away at perforation
on Mounting Gasket (5)
(2)
(6)
(4)
Mounting Plate (6) to Mounting Bar (2)
(9)
using Mounting Bar Screw (9).
L
Do not over-tighten.
D
N
G
N
(6)
(5)
(7)
directly to Terminal Block (7).
Secure wires to Terminal Block
by using a small screwdriver.
See below.
CONNECT:
DETAIL
Black wire to"L" input.
Ground wire to "GND" input.
White wire to "N" input.
N
GND
L
Fixture Body (10) to the Mounting Plate Screws (8).
Secure Fixture Body (10) to Mounting Plate (6) using
Rubber Washers (12) and Decorative Nuts (13).
(10)
(8)
(6)
(11)
(12)
(13)
if connected to one. Ensure lights work before proceeding to step 8.
around the base of the fixture to prevent moisture from reaching
the connections.
Continued
Advertisement
