Feit Electric SEC3000/CAM/RP Installation Manual

INSTALLATION CONTINUED
9. POSITION MOTION SENSOR AND CAMERA
For optimal performance, base of
motion sensor should be placed parallel
and 9 feet above the ground.
Camera can be angled in a different
direction than lights.
PARALLEL TO GROUND
9 Ft
The motion detector is
optimized to detect human size
objects for up to 30 ft.
10. APP SETUP
Download and install the Feit Electric app
Search for the Feit Electric app in
the App Store or Google Play Store.
Download and install the Feit
Electric app on your smart device. Feit Electric App
Set up the ood light camera using the Feit Electric app
Check to be sure the flood light camera is in
pairing mode. The BLUE indicator light must be
blinking rapidly to connect. If not already
blinking, press and hold the Reset Button until
you hear an audible tone. Use the Feit Electric
app to complete the set up.
Tap Add Device or the + sign, then select
Flood Light Camera and confirm. You will
be prompted to enter your Wi-Fi network
and password.
Be sure to connect to a 2.4 GHz Wi-Fi network
that covers your installation location.
Optional - Connect to Google Assistant or Alexa using the
in app guide
Tap Pen icon Choose Alexa
or Google Assistant
Optional - See App User Guide to setup Siri Shortcuts
Need Help?
FAQs and the latest versions of user guides can be found at feit.com/help
and feit.com/smart.
To reach customer support please visit feit.com/contact-us
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
TROUBLESHOOTING TIPS Q & A
Camera will not connect to my Wi-Fi network
• Make sure the LED is blinking blue. If the LED is blinking red, you will need to press
and hold Reset Button located behind the cover on the side of the camera
(see the Resetting Unit & Accessing SD Card section).
• Make sure the Wi-Fi network is a 2.4GHz network, device will not connect to a
5GHz network.
• Test your Wi-Fi network with other devices such as your phone or computer to make
sure it is operating properly.
• The Wi-Fi connection may be out of range during pairing. Use your phone to check
range, it is recommended to have at least 2 signal bars showing for proper connection.
• Your Wi-Fi network password is case sensitive, make sure you are entering it correctly.
The camera is o -line
• There could be a temporary issue with your internet connection (e.g., service
disruption). Please try again in a few minutes.
• Make sure your Wi-Fi router is turned On.
• The camera may not have power to it, make sure the wall switch and breaker is
in the On position.
• Cycle the power Off and On. You will hear an audible tone and the status LED should
blink red then to a solid blue in about 1 minute. If it does not turn blue after a minute,
please go through the setup process again to reconnect to your Wi-Fi signal.
• Make sure the camera is getting a good signal from your Wi-Fi router. Use your phone
to check range, it is recommended to have at least 2 signal bars showing for
proper connection.
• The camera may have been disconnected from your Wi-Fi network, press and hold
Reset Button (see the Resetting Unit & Accessing SD Card section) until you see a
blinking blue LED and hear an audible tone.
What do the blinking LEDs mean?
• Blinking BLUE = Pairing Mode • Solid RED = Rebooting
• Blinking RED = No Wi-Fi Connection • Solid BLUE = Connected to Internet
Live video stream is slow to load
Camera streaming issues may be caused by any of the following:
• Your phone's cellular connection, which is reliant on mobile coverage and
signal reception is slow.
• Limited internet bandwidth at home, for example, other video streaming services
running at the same time on your network can cause congestion slowing down the
internet upload and download speeds.
• Wi-Fi reception may not be stable or work reliably if the camera's Wi-Fi signal
strength is less than 2 signal bars. You may need to install a Wi-Fi repeater or extender
to boost the Wi-Fi signal.
How to reset the camera to reenter pairing mode?
• Press and hold reset button located behind the cover on the side of the camera
(see the Resetting Unit & Accessing SD Card section) until you see a blinking blue LED
and hear an audible tone.
The camera is not recording?
• Make sure Record Switch is turned On in app, under SD Card Settings. This is located
in the Settings menu on the upper right corner in the control panel.
• Make sure that the microSD card is installed correctly. To confirm the camera is
recognizing the microSD card, go to the SD Card Settings in the Settings menu and
make sure microSD Card Capacity menu shows Total Capacity, Used and Free Space.
If this does not appear you may consider reformatting the microSD card.
WARNING: Reformatting microSD card will delete all videos stored on card.
Please go through the trouble shooting section before doing so or contact our
Customer Support Team.
How do I set the camera to Event or Continuous Recording?
• In the Settings menu under SD Card Settings make sure Record Switch is turned On
and then select Event Recording or Continuous Recording.
How can I check the available space on the SD Card?
In the Settings menu under SD Card Settings, you will see Used Space and Free Space.
Note: Camera will not support microSD cards greater than 128GB.
What happens when the microSD card reaches full capacity?
You will get notification if storage is almost full. Once the microSD card reaches full
capacity, new videos will start rewriting (deleting) over the oldest videos.
Can I use a new microSD card if I do not want to record over existing videos?
Yes, you can use a new microSD card if you do not want to record over existing
videos by removing the side cover on the camera and replacing the exiting microSD
card with a new one as long as it does not exceed 128GB. Once this is completed
you will need to format the microSD card by going to the SD Card Settings in the
Settings menu and pressing Format SD Card then Confirm. WARNING: Reformatting
microSD card will delete all content stored on card.
MODEL SEC3000/CAM/RP
Flood Light Security Camera
Installation Guide
IMPORTANT, RETAIN FOR
FUTURE REFERENCE: READ CAREFULLY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: Reorient or relocate the receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the part responsible for
compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in mobile (min 7.87 in.) exposure condition without restriction.
LIMITED WARRANTY
This product is warrantied to be free from defects in workmanship and materials for up to one year
from date of purchase. If the product fails within the warranty period, please contact Feit Electric at
info@feit.com, visit feit.com/contact-us or call 1-866-326-BULB (2852) for instructions on
replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces
do not allow the exclusion of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state or province to province.
SD™, microSD™, and SDHC™ are trademarks or registered trademarks of SD-3C, LLC in
the United States, other countries, or both.
Only supports
2.4GHz Wi-Fi
Works with
Networks
Feit Electric app
4007044