Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for AS MOTOR Allmaher AS 62 4T B&S
Summary of Contents for AS MOTOR Allmaher AS 62 4T B&S
- Page 1 Operator's Manual Allmäher® AS 62 4T B&S, AS 63 2T ES, AS 63 4T B&S, AS 63 4T Honda From serial number: AS 62 4T B&S: 036019110001, AS 63 2T ES: 034619070001, AS 63 4T B&S: 026917110001, AS 63 4T Honda: 027517110001 Issued: 26 November 2019, V6.0 en-Translation of the Original Operator's Manual...
-
Page 2: Notes On The Operating Manual
dummy Intended use Notes on the operating manual The device is intended only for cutting grass or similar vegetation in well-maintained grounds Dear customer, in agriculture, forestry and preservation of the countryside that are cut at least once a year. Congratulations on your purchase. -
Page 3: Table Of Contents
Contents Starting............ Notes on the operating manual..... Starting the device (2-stroke device)..23 Contact ............ Starting the device (4-stroke device Device data..........without choke)......... 23 Starting the device (4-stroke device Intended use..........with choke)..........23 Explanation of the symbols....Engaging the blade........23 Symbols in the instructions...... - Page 4 Maintenance specifically for 4-stroke device............36 Maintaining the engine......36 Checking the engine oil level....36 Checking the spark plugs......36 Maintaining the air filter......36 Assembly..........37 Scope of delivery........37 Unpacking..........37 Unfolding the device........ 37 Storage ............ Storing the device........
-
Page 5: Explanation Of The Symbols
dummy Inhaltsverzeichnis Explanation of the symbols Warning Hazardous situation Symbols in the instructions Indicates a possibly hazardous situation In these operating instructions, the following with a medium level of risk that, if not symbols are used to denote special dangers. avoided, could result in minor or moderate injury. - Page 6 The quickly rotating blade can cause life threatening injuries or immense property damage! Be especially careful to keep your hands and feet away from the blade when the device is put into operation. Prior to any repair and mainten- ance work, pull off the spark plug connector.
-
Page 7: Type Overview
Type plate Type overview The type plate on the device provides you In this operating manual, the following device with information on the device type and the types are described. technical data. Depending on their equipment, the corres- ponding descriptions of this operating manual apply. -
Page 8: Safety Instructions
Safe handling of fuel Safety instructions Fuel is toxic and highly flammable. There is a Get informed! burn and explosion hazard! Keep fuel away from ignition sources and do For your safety, read these operating instruc- not smoke during handling. tions carefully. -
Page 9: Check The Device Prior To Use
First aid Danger area When swallowing fuel or inhaling fuel vapours, do not force vomiting and immediately consult a doctor. In case of skin contact, immediately wash with water and soap. Change your soiled clothing as soon as you can. Measures in case of a fire In case of a fire, use foam, dry powder extin- guisher, or carbon dioxide (CO... -
Page 10: Use Caution During Operation
Use caution during operation Risk of burns Do not touch the engine or the silencer. These Danger of injury during motor start parts become very hot during operation and Do not start the engine you can get burned. If a jumpy movement oc- curs, the risk of additional injuries can result. -
Page 11: Use Caution When Mowing
Use caution when mowing Vibrations When the device is used over a longer period Risk of injury of time, vibrations can cause disturbances in Risk of injury caused by ejected objects. Never the blood supply of the hands. A generally ac- mow when persons, children, pets or material cepted usage time cannot be determined. -
Page 12: Driving On Slopes
Driving on slopes If the device tilts or slips – Never try to stop a tilting or sliding device. Severe injuries can result. – Remove leaking fluids (oil, fuel, battery acid) from the device and the floor. Deposit of contaminated soil environment friendly ac- Fig. 3: Risk of injury during mowing on slopes due to cording to the local regulation. -
Page 13: Use Caution During Maintenance And Repair
Use caution during maintenance and repair Only carry out work as described in these op- erating instructions. Have an authorised ser- vice centre perform all other work. Only use the blades and spare parts author- ised by “AS-Motor Germany”. Unauthorised blades and spare parts can cause severe injur- ies. -
Page 14: Device Description As 62 4T B&S
Device description AS 62 4T B&S 1 Handlebar with control elements 11 Protection skirt 2 Lever for lateral adjustment of handle- 12 Cover 13 Air filter 3 (not existing) 14 Carburetor 4 Accelerator lever with engine stop 15 Cutting height adjustment rear 5 Starter grip 16 Spark plug connector 6 Ventilation grid... -
Page 15: Device Description As 63 2T Es, As 63 4T B&S, As 63 4T Honda
Device description AS 63 2T ES, AS 63 4T B&S, AS 63 4T Honda The illustration shows AS 63 2T ES 1 Handlebar with control elements 11 Protection skirt 2 Lever for lateral adjustment of 12 Cover handlebar 13 Air filter 3 Tank ventilation 14 Carburetor 4 Accelerator lever / accelerator lever 15 Cutting height adjustment rear with engine stop 16 Spark plug connector... -
Page 16: Control Elements
Vario lever (C) Control elements With the vario lever, you can continuously ad- Handlebar with controls (1) just the speed of the device while the engine is running. MIN: slow MAX: fast Blade clutch lever (D) The engine clutch lever is a guard device. When you release the lever, the blade comes to a standstill within 7 seconds. - Page 17 Accelerator lever (4) Fuel valve (17) AS 63 2T ES AS 62 4T B&S With the accelerator lever, you can change the 1: Closed engine speed and thus control the engine out- 2: Open put. Full throttle Idle speed Fuel valve (17) AS 63 2T ES, AS 63 4T B&S, AS 63 4T Honda 1: Reserve 2: Open Lever for lateral adjustment...
-
Page 18: Operating Elements Only For 2-Stroke Devices
Operating elements only for 2-stroke devices Carburetor (14) with choke and tickler For cold start of the engine, you need the choke (1) and the tickler (2). Open choke: Turn clockwise to the stop. Close choke: Turn anti-clockwise to the stop. Fill carburetor with fuel: Briefly press the tickler until fuel spills out. -
Page 19: Information On Mowing
Information on mowing Prior to starting Prior to mowing, check your device for com- Fuel used (2-stroke devices) pleteness, proper functioning, and cleanliness. A dirty ventilation grid causes overheating of The engine must be run on a mixture of petrol the engine, this can damage the engine. -
Page 20: Fuel Used (4-Stroke Devices)
Notice: You can find on the market ready Tanking up mixed two-stroke fuels. Based on our experi- ence, the ready mixed fuels “STIHL Motomix Warning 1:50”, “ASPEN 2-stroke” and “Oest Oecomix” Fuel is ignited by hot engine parts. can be used. No guarantee can be given for operation of the device with other fuels and ►... -
Page 21: Adjusting Cutting Height
Adjusting cutting height Rear axle AS 62 4T B&S Adjust the cutting height setting only when the The height on the rear axle can be adjusted to engine is switched off. 5 positions. Set the cutting height so that the blade does 1. -
Page 22: Locking Steerable Front Wheel
Rear axle Locking steerable front wheel AS 63 2T ES, AS 63 4T B&S, AS 63 4T Honda It is more comfortable on an even surface to let The height on the rear axle can be adjusted to the front wheels swivel. If you move crossways 4 positions. -
Page 23: Starting
11. Reopen the choke (turn clockwise). Starting 12. For mowing, set the accelerator lever to the maximum speed. Warning During startup, there is a risk of injury Starting the device caused by the rotating blade. (4-stroke device without choke) ► Make sure that no one is within the danger zone of the blade. -
Page 24: Driving As 62 4T B&S
Turning Driving AS 62 4T B&S Turn the device round only where the grass Warning has been mowed already. Risk of injury caused by tripping or sliding Turning round on an even surface: while pushing the mower, moving it back- 1. -
Page 25: As 63 4T Honda
Turning Driving AS 63 2T ES, AS 63 4T B&S, AS 63 4T Honda Turn the device around only in already mown sections. Warning Turning on a level surface: 1. Switch off the drive. Risk of injury caused by tripping or sliding 2. -
Page 26: Switching Off And Parking (4 Stroke Devices)
Switching off and parking (4 Transport stroke devices) Warning Risk of injury due to the heavy weight of the Warning device. The device can fall over and fall On a slope, the device can roll away. down and cause severe injuries. ►... -
Page 27: Transport Position 2
Transport position 2 1. Release the interlock of the steerable front wheel (4) at both front wheels. 2. Pull off the spring cotter (2) at the crank (1) for height adjustment. 3. Completely flip up the crank (1) for the 8. -
Page 28: Loading
Loading Use suitable ramps for loading that – can carry the empty weight of the device + 200 kg. – are wider than the device. – have a slip-free surface. Notice Risk of damage due to incorrect fastening of straps. ►... -
Page 29: Maintenance
Improper maintenance can make the device Maintenance unsafe for operation and result in accidents. Regular maintenance keeps your device ready Warning for use. Risk of injury due to unexpected movement. Service the device according to the following When inspections are carried out, the maintenance instructions. -
Page 30: Maintenance Overview
Maintenance overview Component Action Maintenance interval Device Check for safe working condition (basic inspection). ■ ▲ Clean. ■ Customer service. ▲ Fuel Check fuel level. ■ Is the tank cap closed? ■ Tank, fuel valve, Check parts for leaks and check for good condition. ■... - Page 31 Flammable material Remove easily flammable debris buildup from the engine ■ ▲ and the device. Tyres Check tyres and, if necessary, the tyre pressure. ■ ▲ Lubrication See chapter grease lubrication. ■ ▲■ For 4-stroke devices: Engine For reliable information, see the operating manual of the en- ■...
-
Page 32: Cleaning Position
Cleaning position Cleaning the device AS 62 4T B&S Depending on use, clean the device thor- oughly, especially the bottom and the blade. For work on the bottom side of the device, flip the device to the silencer side. Grass cuttings and dirt that are stuck interfere with the grass ejection and impair the cutting quality. -
Page 33: Transmission
Transmission Checking the parking brake The transmission is maintenance-free and AS 63 2T ES, AS 63 4T B&S, AS 63 4T Honda filled with oil that is supposed to last the entire service life of the device. Make sure that there Warning are no leaks or damages. -
Page 34: Checking The Blade
Checking the blade Unusual vibrations are an indication that – blades are missing or broken, Warning – the blade is worn excessively or on one side Wear or damage on the blades and the fastening elements can result in the blades –... -
Page 35: Maintenance Specifically For 2-Stroke Device
Maintaining the air filter Maintenance specifically for 2-stroke device Warning Cleaning agents pose a fire and explosion Maintaining the engine hazard. ► Never clean the air filter with flammable Warning solvents. If the speed of rotation is set too high, ob- jects can be ejected. -
Page 36: Maintenance Specifically For 4-Stroke Device
Checking the spark plugs Maintenance specifically for 4-stroke device Danger The ignition system generates an electro- Maintaining the engine magnetic field. ► Wearers of pacemakers must not work Caution on live parts. If the speed is set too high, objects can be Soiled spark plugs reduce the engine output. -
Page 37: Assembly
1. Pull off the spring cotter (2) between the Assembly guide bar and crank of the height adjust- ment (1) starting from. Scope of delivery 2. Unfold the guide bar until it engages. The device is shipped in a carton. The scope of delivery included: –... -
Page 38: Storage
Storage Spare parts Beware: Do not store or transport the device in The reliable and safe operation of the device cleaning position. also depends on the quality of the spare parts Fuel and oil can leak and soil or damage the used. -
Page 39: Troubleshooting
Troubleshooting The following table contains the most frequent problems and their elimination. If more problems occur, contact the closest authorised service centre. You can find an authorised service centre on our home page www.as-motor.de. Problem Possible cause Remedy Engine does not start Accelerator lever to “0”. Turn the accelerator lever to “idle speed”. - Page 40 Engine starts badly or Choke is closed. Open the choke. runs irregularly Air filter is dirty. Maintain air filter (see Maintenance). Poor quality, dirty, or old fuel. Always use fresh fuel. Spark plug is dirty, damaged, or Clean spark plug and check electrode incorrect electrode gap.
- Page 41 Uneven cut, lawn Blade is dull or worn. Have blade resharpened and balanced becomes unsightly by an authorised service centre. Re- place a damaged blade immediately. Speed is too high proportion- Reduce speed and/or select the correct ately to the cutting height. cutting height.
-
Page 42: Fuel Ratios Of Fuel 2-Stroke Devices
Fuel ratios of fuel 2-stroke devices Fuel Fully synthetic two-stroke oil Only with Titan 2T 100S (octane rating ROZ 91 min.) 1:50 1:100 litres Litre (=ml/cm Litre (=ml/cm 0.02 (20) 0.01 (10) 0.04 (40) 0.02 (20) 0.06 (60) 0.03 (30) 0.08 (80) 0.04 (40) 0.1 (100) -
Page 43: Technical Data As 63 2T Es
Technical data AS 63 2T ES Type AS 63 2T ES Range of application (temperature) 0 - 30 °C Engine, type One cylinder two-stroke engine with easy start Manufacturer AS-Motor Germany Type AS 165 ES (Easystart) Cylinder capacity 165 cm Performance 4,0 kW (5,4 PS) Engine speed 3800 min... -
Page 44: Technical Data 4-Stroke Devices
Technical data 4-stroke devices Type AS 63 4T B&S AS 63 4T Honda 0 - 30 °C Range of application (temperature) Engine, type One cylinder four stroke One cylinder four stroke engine engine Manufacturer Briggs & Stratton Honda Type Series 850, I/C GXV 160 Cylinder capacity 190 cm... - Page 45 Type AS 62 4T B&S Range of application (temperature) 0 - 30 °C Engine, type One cylinder four stroke engine Manufacturer Briggs & Stratton Type Series 850, I/C Cylinder capacity 190 cm Performance 3,7 kW (5,1 PS) Engine speed 3600 min Cutting device, type 2 knives (cross knives) Cutting height 50, 65, 80, 100 mm, per axis...
-
Page 46: Accessories
Accessories Spray paint 400 ml, colour orange: G00011050 Operating hours counter: G06927008 Clinometer: G06950027 Mulching accessory: G60026026 Only applies for AS 63 2T ES, AS 63 4T B&S, AS 63 4T Honda: Twin tires: G06321009 Flat tyre protection 950 ml: G00041068 Flat tyre protection 20 l: G00041069... -
Page 47: Declaration Of Conformity
Declaration of conformity AS-Motor Germany GmbH & Co. KG Ellwanger Straße 15 D-74424 Bühlertann www.as-motor.de Declaration of conformity We declare that the grassland mowers Type AS 62 4T B&S AS 63 2T ES AS 63 4T B&S AS 63 4T Honda starting from serial no. - Page 48 AS-Motor Germany GmbH & Co. KG Ellwanger Straße 15 D-74424 Bühlertann www.as-motor.de THE HIGH GRASS MOWER AND 2 STROKE ENGINE MANUFACTURE AS-Motor is your premium manufacturer for lawn and high grass mowers as well as 2 stroke en- gines. We offer our customers professional technology for steep slopes, rough terrain, and lawn care.
Need help?
Do you have a question about the Allmaher AS 62 4T B&S and is the answer not in the manual?
Questions and answers