Subscribe to Our Youtube Channel
Related Manuals for SIGNAL FIRE AI-9
Summary of Contents for SIGNAL FIRE AI-9
- Page 1 Automatic intelligent optical fiber fusion splicer Automatic intelligent optical fiber fusion splicer 2019.09...
-
Page 2: Table Of Contents
CATALOGUE Safety Requirements Warnings/precautions Chapter I Operation Keys And Parts Introduction Display Menu Introduction Introduction To Splice Interface Chapter II Software Download Software Bluetooth Connection Screen Menu Function On/off Chapter III Smart Lock Chapter IV Toolbox Introduction Chapter V Arc Calibration Chapter VI Fiber Stripping And Put Into Holder Chapter VII Replace Electrode Chapter VIII Activate Electrode... -
Page 3: Safety Requirements
SAFETY REQUIREMENTS WARNINGS/PRECAUTIONS AC/DC Adapter At any stage of operation on the optical fiber fusion splicer, you must take the following general safety The Output Characteristics Of The Power Adapter Must Meet The Following Quirements. precautions. Not take these warnings and precautions or not comply with the warnings which described in this Voltage: 12V-14V;... - Page 4 WARNINGS/PRECAUTIONS WARNINGS/PRECAUTIONS carry case should be used for storage, and suitable cushioning case should be added outside the carry case for long- storage (storage time less than or equal to 6 months) is: -20℃~60℃. distance transportation. 4.In order to ensure the safety of charging, the charging temperature range of lithium battery inside the welding machine is O℃~ 40℃.
- Page 5 CHAPTER I OPERATION KEY COMBINATION FUNCTION OPERATION KEY COMBINATION FUNCTION Introduction of operation keys and parts ORESET The four function keys at the bottom of the screen, in addition to the basic functions (the first chapter introduces the The fusion splicer machine is mainly used Press the reset key to reset the propulsion motor, adjustable operation keys and parts), there are also some combined functions for daily maintenance of the machine.
- Page 6 OPERATION KEY COMBINATION FUNCTION OPERATION KEY COMBINATION FUNCTION report an error,Please check whether the red light above the electrode is bright and dim(see electrode replacement for specific operations)If the 08 Camera LED: X Y Camera LED:two fault persists,Please contact the after-sales service. Report an error,please check again.
-
Page 7: Display Menu Introduction
DISPLAY MENU INTRODUCTION INTRODUCTION TO SPLICE INTERFACE Optical power display area Heating time NAME FUNCTION ICON Y screen display X screen display Normal Bluetooth Normal Splicing Mode For The Machine mode Fiber mode When the function is on the splicing machine will stop the final splicing process after in Splicing the completion of the fiber focus, end face detection and fiber alignment. - Page 8 INTRODUCTION TO SPLICE INTERFACE INTRODUCTION TO SPLICE INTERFACE Intelligent prompt and fiber state prompt solution different, and they need to be replaced with the same specifications or types.This error, can press continue to ignore the key error, mandatory welding. Ⅰ Intelligent prompt Note: according to the construction specifications of welding machine, different specifications and types of fiber cannot be fused, if forced welding, welding quality may be affected.
- Page 9 INTRODUCTION TO SPLICE INTERFACE INTRODUCTION TO SPLICE INTERFACE Ⅱ fiber state prompt Fiber is too short The optical fiber symbol in the middle below the LCD, two blue and white bars represent V groove, the small The front end of the optical fiber identification is returned to the v-groove identification, indicating that the triangle in the middle represents electrode tip, and the black bar flashing on the blue and white bars optical fiber is placed too short and should be placed beyond the v-groove.
-
Page 10: Software Download
CHAPTER II SOFTWARE DOWNLOAD INTRODUCTION TO SPLICE INTERFACE Software download The test is fiber passing Fiber passing means screen display is a complete fiber, take out fiber can be normal. Sometimes errors may be reported due to dirty lens or fog, and the lens can be restored after cleaning (see daily maintenance for specific operations). -
Page 11: Software Bluetooth Connection
SOFTWARE BLUETOOTH CONNECTION SOFTWARE BLUETOOTH CONNECTION The mobile phone is not needed when splicing, The mobile APP can be used to turn on off the machine menu, arc calibration remote control smart lock. etc You can also learn various operations in the app, as well as contact after-sales support, or you can update the mobile app and connect to the machine to synchronize updates Phone settings 2. - Page 12 SOFTWARE BLUETOOTH CONNECTION SCREEN MENU FUNCTION ON/OFF Turn on the phone bluetooth, open the phone app, set the machine panel menu after establishing the connection, and machine will update at the same time. The splicing operation does not require phones, the phone App is only for machine menu settings, and splicer machine to store data.when the data is exported to phone App, the users can also get support through the APP and after-sales service.
-
Page 13: Screen Menu Function On/Off
SCREEN MENU FUNCTION ON/OFF CHAPTERⅢ SMART LOCK Smart Lock Purpose: to facilitate management or owner's effective management of the splicer machine's When the settings are saved, the display icon will be highlighted darkened accordingly.otherwise please check whether the bluetooth is properly connected.c use period or the number of splicing. -
Page 14: Chapter Iii Smart Lock
SMART LOCK CHAPTER IV TOOLBOX INTRODUCTION A Device Can Only Be Bound To One Mobile Account At The Same Time. To Bind Other Mobile Phones. You Need To Unbind Current Account First. Lock catch Tool layer Platform for fiber cleaving Accessory layer 3. -
Page 15: Chapter V Arc Calibration
CHAPTER V ARC CALIBRATION CHAPTER VI FIBER STRIPPING AND PUT INTO HOLDER ARC Calibration: According to the local ground elevation, temperature, moderate and other environmental Cleave fiber instructions: factors to match the most suitable discharge ARC, in order to obtain the bestsplicing effect, we strongly Jumper fiber(pigtail fiber) Rubbe insulated fiber Bare fiber... -
Page 16: Chapter Vii Replace Electrode
CHAPTER VII REPLACE ELECTRODE REPLACE ELECTRODE Electrode replacement must use the genuine original electrode designed for this machine from factory. When the number of electrode is used close to 3000 times, the machine will remind you to replace it. When it reaches to 3000 times, it is necessary to replace the electrod and activate it then you can use again(see page 29 ACTIVATE ELECTRODE). -
Page 17: Chapter Viii Activate Electrode
CHAPTER Ⅷ ACTIVATE ELECTRODE ACTIVATE ELECTRODE PS. The electrodes on the new machine do not need to activate we have activated before ex-factory. Only when the electrodes life on the machine is expired in the future mand then you need to replace activate the electrode hen the electrode is used up to 3000 times, you need to replace the electrode and activate it. -
Page 18: Chapter Ix Power Meter And Optical Modules
CHAPTER IX POWER METER AND OPTICAL MODULES POWER METER AND OPTICAL MODULES Effect easure connection loss, verify continuity, and help evaluate fiber link transmission quality Optical power meter and VFL parameter settings The fusion splicer screen displays the measurement results Optical power meter input VFL output 1.The user logs in to the "signalfire2"... -
Page 19: Chapter Xi Daily Maintenance
CHAPTER X DAILY MAINTENANCE DAILY MAINTENANCE Ⅱ.Prevent Strong Shock or Vibration Ⅰ.Pay attention to dustproof and remove dust When you need to move or transport the fusion splicer, you should handle Bare fiber positioning groove, electrodes and microscopes must be kept clean and windshield cover should with care and gently. - Page 20 DAILY MAINTENANCE DAILY MAINTENANCE Ⅴ.Troubleshooting and solutions The table lists a general troubleshooting method for the user reference. Reason Solutions Troubleshooting When the user can not solve the situation, please contact with the suppliers directly. 1.Fiber core does not match (type or core diameter 1.Re-match the fiber to make the same type of fiber on Splicing points is different)
- Page 21 DAILY MAINTENANCE DAILY MAINTENANCE 4.The bottom left corner of the machine shows a red box with a red dot in the middle -- this is a focus failure. 1.The optical fiber has been placed, but the machine Wipe the lens with a cotton swab, clean the V slot, press the reset key on the far left of the machine and indicates that the optical fiber is not in the slot -- -- one replace the fiber.
- Page 22 DAILY MAINTENANCE DAILY MAINTENANCE 8.High welding loss or no connection--the loss of welding is determined by many reasons: the quality of the 7.One side of the optical fiber is up or down and cannot be restored by cleaning the V slot and resetting -- open the mobile phone APP and connect it to the machine, then select the welding setting -- operation mode machine, the current intensity of the machine, the flatness of the cutting surface, the cleanliness of the -- factory core adjustment, and select manual adjustment when returning.
- Page 23 DAILY MAINTENANCE DAILY MAINTENANCE 12.Always suggest that the cutting surface does not meet the requirements, resulting in no welding. This is 9.Easily broken fiber -- -- if it is broken from the welding point, generally is the current is not appropriate, mainly the following two cases, one is V groove dirty, optical fiber did not enter the groove (as shown in the redo the discharge calibration on the line.
-
Page 24: Chapter Xii Lighting And Power Supply
CHAPTER XI LIGHTING AND POWER SUPPLY Lighting: night lighting is convenient for construction work Mobile phone charging: the device can reverse the power supply to the mobile phone Mobile phone charging diagram Lighting use diagram...
Need help?
Do you have a question about the AI-9 and is the answer not in the manual?
Questions and answers