Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Redexim Verti-Top Walk Behind
Summary of Contents for Redexim Verti-Top Walk Behind
- Page 1 Model: Serial number: ATTENTION: IT IS OF THE UTMOST IMPORTANCE TO READ THIS USER MANUAL CAREFULLY ® PRIOR TO USING THE VERTI-TOP WALK BEHIND IN ORDER TO USE THE MACHINE SAFELY AND TO OBTAIN THE BEST RESULTS. 1703 English 947.120.206...
-
Page 2: Foreword
Congratulations on your Verti-Top Walk Behind purchase! For safe and long-lasting operation of this Verti-Top Walk Behind, it is necessary to read and to understand this user manual. It is impossible to work safely with this machine without complete knowledge of its content. -
Page 3: Safety Instructions
Safety Instructions. The user is responsible for safe use of the Verti-Top Walk Behind. The user is obliged to check the Verti-Top Walk Behind for visible damage and defects before using the Verti-Top Walk Behind. Modifications to the Verti-Top Walk Behind (including its operations) that have a negative impact on safety must be rectified immediately. - Page 4 If modifications to the Verti-Top Walk Behind have been made, then the current CE marking is cancelled. The person that has made these modifications has to apply for a new CE marking himself. Check the Verti-Top Walk Behind for loose bolts, nuts and components before every operation.
- Page 5 Relevant traffic regulations also apply in case of using public roads. Transporting persons is not permitted! Do not use the Verti-Top Walk Behind in the dark, in heavy rain/storm or on slopes with an angle larger than 20 degrees. All persons that are going to operate the Verti-Top Walk Behind must be familiar with all the functions and control elements of the Verti-Top Walk Behind before starting any work activities.
- Page 6 Dress appropriately. Wear sturdy shoes with steel toecaps, long trousers and tie up long hair. Do not wear loose clothing. Use the proper personal protection gear according to the applicable health & safety (Dutch acronym: ARBO) and safety regulations. Figure 7 Use certified ear protection when using the machine! (Figure 7) Figure 8...
-
Page 7: Table Of Contents
LIST OF GENERAL COMPONENTS ................10 ADJUSTING THE WORKING DEPTH OF THE BRUSH ..........11 ADJUSTING THE ANGLE OF THE JIGGING SIEVE ............ 12 TRANSPORTING THE VERTI-TOP WALK BEHIND ............ 13 USING THE VERTI-TOP WALK BEHIND ..............13 START/STOP PROCEDURE ..................14 EMPTYING THE WASTE RECEPTACLE .............. -
Page 8: Technical Data
TECHNICAL DATA Model V-Top WB Working width 800mm Working depth (In case of a non- 0 mm-10mm (0”-0.4”) worn brush) Speed 0 – 3.5 km/h 0 – 2.5 mph Weight 150 kg (330 lbs) Content of the receptacle 30 litres (1830.7 cu. inch) Maximum capacity 2800 m /h (30139 ft... -
Page 9: First Installation - Taking The Machine Off The Pallet
FIRST INSTALLATION – TAKING THE MACHINE OFF THE PALLET Figure 9 The machine in transport position is delivered on a pallet. To remove the pallet and to prepare the machine, you take the following steps (see Figure 9) NEVER crawl under the machine! Remove the straps (1) with which the machine is fixed to the pallet. -
Page 10: List Of General Components
LIST OF GENERAL COMPONENTS Figure 10 shows several important components: Figure 10 Safety sticker 900.280.402; first read the user manual / toolbox before using it. Safety sticker 933.280.402; onlookers without personal protection gear must keep a distance of 4 metres from the machine. Switch off the motor and detach the spark plug cable from the spark plug in case adjustment or repair is necessary. -
Page 11: Adjusting The Working Depth Of The Brush
The procedure is as follows (see Figure 11) Make sure that the Verti-Top Walk Behind is blocked well and cannot move on its own accord! Switch off the Verti-Top Walk Behind before making adjustments! 1. If this has not been done yet, put the spindle in the upper position of the slotted hole. -
Page 12: Adjusting The Angle Of The Jigging Sieve
This is done by placing the jigging sieve under an angle. The procedure is as follows (see Figure 12) Make sure that the Verti-Top Walk Behind is blocked well and cannot move on its own accord! Switch off the Verti-Top Walk Behind before making adjustments! 1. -
Page 13: Transporting The Verti-Top Walk Behind
Tighten the stellar knobs (1) on both sides of the machine. USING THE VERTI-TOP WALK BEHIND Before using the Verti-Top Walk Behind in a location, you should check the following items: Are there loose objects in the field? First remove these objects. -
Page 14: Start/Stop Procedure
/ subsoil could be the result. The start procedure is as follows (see Figure 14) 1. Check the Verti-Top Walk Behind for loose components and look whether all components function properly. If loose components are observed or components do not function... - Page 15 2. Decrease the number of revolutions by adjusting the throttle (2). 3. Stop de motor. The Verti-Top Walk Behind is standard adjusted to drive straight. This can easily be adjusted so that short bends can be taken (e.g., for cleaning around a pole).
-
Page 16: Emptying The Waste Receptacle
The procedure is as follows (see Figure 13) 1. Drive the Verti-Top Walk Behind to the waste-collection dump. Make sure that the Verti-Top Walk Behind is blocked well and cannot move on its own accord! Switch off the Verti-Top Walk Behind before proceeding! 2. -
Page 17: Trouble Shooting (Problem Analysis)
11.0 EU DECLARATION We – Redexim BV, Utrechtseweg 127, 3702 AC Zeist, Holland – declare entirely under our own responsibility that the product VERTI-TOP WALK BEHIND with a machine number as indicated on the machine and indicated in this manual... -
Page 18: Maintenance
12.0 MAINTENANCE Time Schedule Check/Grease Point Method Before every use Check for loose Tighten loose bolts/nuts bolts/nuts with the correct tightening moment Presence and readability Replace these if not of the safety stickers present or damaged (Please refer to Figure 8) After the first 20 working Check the roller If required, replace the... -
Page 19: Adjusting The Tension Of The V-Belts
12.1 ADJUSTING THE TENSION OF THE V-BELTS Figure 17 The Verti-Top Walk Behind is standard equipped with adjustable tension pulleys that keep the V- belts taut. The system can be divided into 2 segments. 1. Tension pulley for the drive of the brush (see Figure 17) 2. - Page 20 V-belt should couple and should engage with the pulley of the motor without slipping. Make sure that the Verti-Top Walk Behind is blocked well and cannot move on its own accord! Switch off the Verti-Top Walk Behind before proceeding! 1.
-
Page 21: Changing The Jigging Sieve
12.2 CHANGING THE JIGGING SIEVE Figure 19 Verti-Top Walk Behind comes with various sieves with different meshes for processing the different types of materials. Changing the jigging sieve is done as follows (see Figure 19) Make sure that the Verti-Top Walk Behind is blocked well and cannot move on its own accord! 1. -
Page 22: Options For Other Jigging Sieves
It is possible to mount another sieve with a larger or smaller mesh if a different type of material has to be sieved or the material has other dimensions for which the standard mounted jigging sieve is inadequate. The following sieves are available for the Verti-Top Walk Behind: Mesh (mm) Mesh (inch) Spare part number 3.2x3.2...
Need help?
Do you have a question about the Verti-Top Walk Behind and is the answer not in the manual?
Questions and answers