Table of Contents
Advertisement
User Manual and Parts
Book
Carrier
Serial number:
Translation of the original User Manual
ATTENTION:
IT IS OF THE UTMOST IMPORTANCE TO READ THIS USER MANUAL CAREFULLY
PRIOR TO USING THE CARRIER IN ORDER TO USE THE MACHINE SAFELY AND TO
OBTAIN THE BEST RESULTS.
1703 English 951.120.200
Kwekerijweg 8
3709JA Zeist
The Netherlands
T: (31)306933227
F: (31)306933228
E: verti-drain@redexim.com
www.redexim.com
Advertisement
Table of Contents
Related Manuals for Redexim Carrier
Summary of Contents for Redexim Carrier
- Page 1 Translation of the original User Manual ATTENTION: IT IS OF THE UTMOST IMPORTANCE TO READ THIS USER MANUAL CAREFULLY PRIOR TO USING THE CARRIER IN ORDER TO USE THE MACHINE SAFELY AND TO OBTAIN THE BEST RESULTS. 1703 English 951.120.200...
-
Page 2: Warranty Conditions
It is impossible to work safely with this machine without complete knowledge of its contents. The Carrier is NOT a machine that cultivates the soil independently. It is the user’s responsibility to use the correct combination with this machine. The user must also check the Carrier/Processing Machine combination on safety aspects such as noise level, user instructions and risk analysis. -
Page 3: Safety Instructions
Always use the Carrier in combination with soil-cultivating machines that are suitable for this work. See the technical data or ask your dealer about the possibilities. 3. All persons assigned to operate, maintain and repair the Carrier by the owner must completely read and understand the operation manual and in particular the chapter of Safety Instructions. - Page 4 Relevant traffic regulations also apply in case of using public roads. Transporting persons is not permitted! Do not use the Carrier in the dark, in heavy rain/storm or on slopes with an angle larger than 20 degrees. 6. All persons that are going to operate the Carrier must be familiar with all the functions and control elements of the Carrier before starting any work activities.
- Page 5 Figure 3 Figure 4 Figure 5 Figure 6 During operation, NO persons are allowed within the danger zone of the Carrier, because there is danger of physical injuries caused by moving components. (Figure 3) Keep a distance of minimum 4 metres!
-
Page 6: Eu Declaration
3702 AC Zeist, Netherlands declare entirely under our own responsibility that the product CARRIER WITH A MACHINE NUMBER AS INDICATED ON THE MACHINE AND INDICATED IN THIS MANUAL to which this declaration refers, complies with stipulation of the 2006/42/EC machine... -
Page 7: Table Of Contents
GENERAL DESCRIPTION ..................8 3.0 FIRST INSTALLATION – TAKING THE MACHINE OFF THE PALLET ..... 9 4.0 OPERATING THE CARRIER ..................10 5.0 ATTACHING A MACHINE TO THE CARRIER ............13 5.1 VERTI-DRAIN 1513 ATTACHING ................14 5.2 BALLASTING WHEELS .................... 14 6.0 ... -
Page 8: Technical Data
The values measured values are applicable to the Carrier without tools. GENERAL DESCRIPTION The Carrier is a machine/vehicle that can be used for various work activities in combination with certain processing machines e.g., the Verti-Drain 1513 for grass aeration. -
Page 9: First Installation - Taking The Machine Off The Pallet
12. Check the level in the tank of the hydraulic oil. If needed, top it up. 13. Fill the fuel tank. 14. Connect the machine to the vehicle (please refer to Chapter 5.0). Turn the Carrier off and make sure the Carrier/vehicle combination cannot drive off! -
Page 10: Operating The Carrier
OPERATING THE CARRIER Later models: Figure 9 The Carrier is operated by means of a number of handles that are located on the steering bar. The parking brake (1) The parking brake is solely intended for blocking the machine. If the Carrier is not used with the steering bar, the machine must always be in the parking position (towards the engine block). - Page 11 The main switch turns ON the electric clutch and the PTO that leads to the processing machine. Switch the main switch ON before processing. The PTO will only engage when the Carrier is in a forward movement and the processing machine is lowered. This is regulated by the switches in the machine.
- Page 12 Line marker (8) The machine is equipped with a line marker. In combination with the Verti-Drain 1513 as the previous course with holes will be followed, at 55 mm (2.1 ") distance between the new job be pricked. In this way, the user can use the machine in the most efficient way. When the line marker is not necessary.
-
Page 13: Attaching A Machine To The Carrier
The procedure is as follows (Figure 12) 1. Using the cylinder (1), lower or raise the lower lifting arms (2) of the Carrier up to the height of the lower connection points of the processing machine. 2. Reverse the vehicle carefully so that the lower lifting arms (2) of the Carrier can be attached to the processing machine. -
Page 14: Verti-Drain 1513 Attaching
Make sure that the Carrier is blocked well and cannot move on its own accord! Turn the Carrier off before starting to attach a machine! Make sure that the processing machine stands stable and cannot roll away and/or slide off! 4. -
Page 15: Transporting The Carrier
90° Figure 14 In the event of a defect, for example the engine can be the carrier moved without starting it. To transport the Carrier without engaging its motor, the Carrier can be put into neutral. To do this, remove the main cover and put the pump in the neutral position by turning handle ‘A’... -
Page 16: Using The Carrier
USING THE CARRIER Before using the Carrier in a location, you should check the following items: 1. Are there loose objects in the field? First remove these objects. 2. Are there slopes? The maximum slope is 20 degrees for this machine. - Page 17 13. If required, adjust the speed by operating the speed handle (3). In order to do this, first lift the machine, stop the combination, switch the processing machine OFF and put the Carrier in the parking position. Afterwards, set the new driving speed. Now follow the procedure as described above.
-
Page 18: Detaching A Machine From The Carrier
The machine can be detached from the vehicle in the following manner (See Figure 16) 1. Drive the Carrier to a parking area with a firm/flat surface. Make sure that the Carrier is blocked well and cannot move on its own accord! Switch the Carrier OFF before detaching the processing machine! 2. -
Page 19: Adjusting The Tension Of The V-Belts
11.0 ADJUSTING THE TENSION OF THE V-BELTS The Carrier has two systems that are driven by V-belts. Standard setting A = 8mm (0.3") B = 13mm (0.5") Figure 17 First, the motor drives the pump by means of a single V-belt. To adjust the tension of this V-... - Page 20 5. Subsequently, tighten the bolts and nuts (1) that connect the gearbox with the main frame. 11.1 PRECISION ADJUSTMENT OF THE DRIVING SPEED If the driving speed of the Carrier needs adjusting, it can be adjusted by altering the stop bolt of the pump (See Figure 17) 1.
- Page 21 11.2 ENGAGING MOMENT OF THE PTO In the Carrier, the engaging moment of the PTO is regulated automatically when the attached machine is moved downward. The engaging moment can be changed as follows (See Figure 19) Fig. 19 1. Lower the machine up to the point when the PTO should be engaged.
-
Page 22: Trouble Shooting (Problem Analysis)
12.0 TROUBLE SHOOTING (PROBLEM ANALYSIS) Problem Possible cause Solution Engine does not start/run. Battery is empty. Check the battery. Charge or replace the battery. Wiring is damaged. Check the wiring for short-circuits. Check the battery terminals. No petrol Check the petrol level. Use the choke. -
Page 23: Maintenance
Drain off the old oil in compliance with local regulations. Please refer to the engine manual, which is supplied with the Carrier, for maintenance of the Briggs & Stratton motor. See the Parts Manual for part numbers and schematic drawings.
Need help?
Do you have a question about the Carrier and is the answer not in the manual?
Questions and answers