Advertisement
LED FOLDABLE LIGHT
6.Scenes
Use the selector knob to highlight the desired mode. Push the knob once to enter. Use the selector, saturation
and intensity knobs to adjust the parameters.
-----(CCT mode) CCT:2800-10000 K INT: 0-100%
GN: -1 / +1
*Mode TWO G+B, R+G+B, R+G, R+B
-----(HSI mode) HUE: 0-360゜, SAT: 0-100% INT: 0-100%
*Mode THREE
-----(RGBWT mode) Red: 0-100% Green: 0-100% Blu: 0-100% W:0-100% T: 0-100%
7.[Lang] (language)
Use the selector knob to highlight the desired language. Push the knob once to select.
*English
*Chinese
8.DMX settings
Adjust the DMX address using the selector knob, push the knob to select the address.
DMX Address: 001-512
9.RMT settings (remote control settings)
Remote control operating instructions:
( ) On the light, go to menu and enter RMT settings. Set the desired wireless receiving address from 0-511.
1
(2) On the remote control, go to menu and enter RMT settings. Set the desired wireless receiving address from 0-511.
(3) Make sure the wireless receiving address on the light matches the light receiving address on the remote control.
The remote control can control multiple lights at the same time.
(4) The wireless remote control has a working distance of approximately 65 feet (20 meters).
Note: After setting the wireless receiving address in the RMT settings on the light, you cannot change the address
through the remote control. You can only manually adjust it through the RMT settings on the light.
10.Factory reset
To restore the light or remote control to factory settings:
Press and hold the MENU button on the light or on the remote control for more than 4 seconds in the main menu
on the light, the entire device will reset, and the data will be restored to the factory setting state.
25
LED FOLDABLE LIGHT
11.DMX connection
When operating DMX, connect the DMX cable to the console (the specific wiring is shown in the diagram
below), then set the DMX address to match the console address.
DMX
512
console
DMX single light connection diagram
light 1
DMX
512
console
DMX multiple light connection diagram
12.DMX control: First, the menu needs to be switched to the DMX control interface.
Note: Seven channels are required for proper DMX control over all parameters.
For example:
In DMX address setting 1, 1-1 is brightness control, 1-2 is color temperature control, 1-3 is red and green
deviation control, 1-4 is saturation control, 1-5 is monochrome red control, 1-6 is monochrome green
control, and 1-7 is monochrome blue control.
DMX address comparison table:
LCD display address
1-1(
brightness
)1-2(
color temperature
1
12(
- brightness)
1-3(
color temperature)
2
1-16(
brightness)
2-1(
color temperature)
16
17
2-1(
brightness)
2-2(
color temperature)
32-10(
brightness)
32-11(
color temperature)
32-12(
506
507-512
All Fotodiox products are backed by a 24 month limited warranty.
light
light 2
light 3
8 Bit
10 Channels
DMX console channels
)1-3(
red/green deviation
)1-4( ) 1-5(
sat
red
) 1-6(
green
) 1-7(
blue
)
1-4(
red/green deviation)
1-5
(sat)
1-6
(red)
1-7
(green)
1-8
(blue)
2-2(
red/green deviation)
2-3
(sat)
2-4
(red)
2-5
(green)
2-6
(blue)
2-3(
red/green deviation)
2-4
(sat)
2-5
(red)
2-6
(green)
2-7
(blue)
red/green deviation)
32-13
(saturation)
32-14
(red)
32-15
(green)
32-16
(blue)
26
Advertisement
