General - Sony TRINITRON KV-HA21M80 Service Manual

The operating instruction mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
A
Getting Started
Step 1
Insert the batteries (supplied) into the remote.
Note
• Do not use old batteries nor use different types of batteries
together.
Step 2
Connect the antenna cable (not supplied) to 8
(antenna input) at the rear of the TV.
Tip
• You can also connect your TV to other optional components.
(See E)
Step 3
Plug in the power cord, then press ! on the TV to
turn it on.
!
Step 4
CABLE
Press CABLE on the remote to select "CABLE: ON",
then press AUTO PROGRAM on the remote to preset
the channels automatically. (See J)
AUTO
PROGRAM
Tip
• To stop the automatic channel presetting, press SELECT.
SELECT Step 5
Press SELECT on the remote until "LANGUAGE/
+ or – to change the on-screen display language.
A
Getting Started
Step 1
Insert the batteries (supplied) into the remote.
Note
• Do not use old batteries nor use different types of batteries
together.
Step 2
Connect the antenna cable (not supplied) to 8
(antenna input) at the rear of the TV.
Tip
• You can also connect your TV to other optional components.
(See E)
Step 3
Plug in the power cord, then press ! on the TV to
turn it on.
Step 4
SELECT
Press SELECT and PROGR + on the TV at the same time
for one to two seconds to preset the channels
automatically. (See J)
PROGR
Tip
• To stop the automatic channel presetting, press SELECT.
SELECT Step 5
Press SELECT on the remote until "LANGUAGE/
ENGLISH" appears on the screen, then press + or – to
change the on-screen display language.
SECTION 1 GENERAL
(KV-HA21N80/HA21N70)
: ENGLISH" appears on the screen, then press
(KV-HA21M80)
:
– 7 –
KV-HA21M80/HA21N70/HA21N80
RM-969
B
WARNING
• Dangerously high voltages are present inside the TV.
• TV operating voltage: 110 – 240 V AC.
• Do not plug in the power cord until you have completed making all other connections;
otherwise a minimum leakage current might flow through the antenna and other terminals to
ground.
• To avoid battery leakage and damage to the remote, remove the batteries from the remote if
you are not going to use it for several days. If any liquid that leaks from the batteries touches
you, immediately wash it away with water.
For your own safety, do not touch any part of the For children's safety, do not leave children alone
TV, the power cord and the antenna cable during with the TV. Do not allow children to climb onto
lightning storms. it.
Do not operate the TV if any liquid or solid object
To prevent fire or shock hazard, do not expose falls into it. Have it checked immediately by
the TV to rain or moisture. qualified personnel only.
Do not block the ventilation openings of the TV. Clean the TV with a dry and soft cloth. Do not use
Do not install the TV in a confined space, such benzine, thinner, or any other chemicals to clean
the TV. Do not scratch the picture tube.
as a bookcase or built-in cabinet.
Do not open the cabinet and the rear cover of the Your TV is recommended for home use only.
TV as high voltages and other hazards are Do not use the TV in any vehicle or where it may
present inside the TV. Refer servicing and be subject to excessive dust, heat, moisture or
disposal of the TV to qualified personnel. vibrations.
WARNING (continued)
Do not plug in too many appliances to the same
Do not place any objects on the TV. power socket. Do not damage the power cord.
Pull the power cord out by the plug. Do not pull
the power cord itself. Even if your TV is turned
Install the TV on a stable TV stand and floor which off, it is still connected to the AC power source
can support the TV set weight. Ensure that the TV (mains) as long as the power cord is plugged in.
Unplug the TV before moving it or if you are not
stand surface is flat and its area is larger than the
bottom area of the TV. going to use it for several days.
C
Securing the TV
To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV.
20 mm
3.8 mm
clamps
screws
Screw the band to the TV stand and to the
provided hole at the rear of your TV.
or
(1) Put a cord or chain through the
clamps.
(2) Screw one clamp to a wall or pillar
and the other clamp to the provided
hole at the rear of your TV.
Note
• Use only the supplied screws. Use of other screws may damage the TV.
RM-968
band