Related Manuals for Connected IO EM1000T-NA-CAT1
Summary of Contents for Connected IO EM1000T-NA-CAT1
- Page 1 EMU CAT1 Modem User Manual Revision: V.05 EMU CAT1 Modem User Manual Rev: V0.5 January 31, 2017 Connected IO Inc. CONFIDENTIAL...
- Page 2 Initial draft Engineering 02/07/2017 V0.2 Update Section 5.2 APN Change Engineering 02/14/2017 V0.3 Clean-up and initial Release Engineering 03/15/2017 V0.4 Antenna and Certs Clean-up Engineering 10/11/2017 V0.5 Set-up Figure clean up. Engineering P a g e Connected IO Inc. CONFIDENTIAL...
-
Page 3: Table Of Contents
7.2. Maximum Antenna Gain .......................... 25 7.3. Recommended Antennas ......................... 25 Environmental ............................25 8.1. Operating Environment ..........................25 8.2. Physical Parameters ..........................25 Approvals and Certifications ........................25 9.1. Manufacturing............................25 P a g e Connected IO Inc. CONFIDENTIAL... - Page 4 EMU CAT1 Modem User Manual Revision: V.05 9.2. North American Certifications ........................26 9.2.1 EM1000T-NA-CAT1 ..........................26 9.2.2 EM1000T-VZ-CAT1 ........................... 26 P a g e Connected IO Inc. CONFIDENTIAL...
-
Page 5: Introduction
Revision: V.05 1. Introduction The Connected IO EMU CAT1 Modem is designed for applications leveraging Low Category LTE technology. These LTE CAT1 modules will deliver data rates of 10Mbps downlink and 5 Mbps uplink in an optimized network like Verizon or AT&T. The EMU CAT1 Modem is a compact module offering LTE connectivity with 3G fallback across numerous carrier independent networks depending on the end customers’... -
Page 6: Device Driver And Software Documentation
3.1. Device Driver and Software Documentation To locate the current device drivers, software updates, and documentation for a particular device requires a user to register his device with Connected IO. This can be accomplished at: https://www.connectedio.com/pages/software 4. Modem Usage in Windows The following Sections, 4, 5, and 6 are excerpts directly from Telit Wireless to help the user manage the EMU Modems, EM1000T-XX-CAT1. - Page 7 Push Settings button, the following dialog box is displayed. The APN is auto-connected to the CID 3. The Packet Data Protocol type is always set to "IP". • See AT command AT#CGDCONT. P a g e Connected IO Inc. CONFIDENTIAL...
-
Page 8: Windows Connection Manager
After installing drivers for the modem, “Telit_Dialup” connection will appear under the Windows Network Interfaces. Please follow the steps below to connect the modem to the internet 1. Click on “Network Interfaces” Desktop icon. P a g e Connected IO Inc. CONFIDENTIAL... - Page 9 EMU CAT1 Modem User Manual Revision: V.05 2. Click on “Telit_Dialup”. Settings menu will appear (see step 3) 3. Click ‘Telit_Dialup” again in the “Settings” menu. P a g e Connected IO Inc. CONFIDENTIAL...
- Page 10 EMU CAT1 Modem User Manual Revision: V.05 4. Click “Connect”. 5. Click “Dial”. P a g e | 10 Connected IO Inc. CONFIDENTIAL...
-
Page 11: System Configuration - Windows
If not, type “Telit AT Controller” in your Windows search field to locate) Verify which serial port the device should be communicating on in the Windows Device Manager. P a g e | 11 Connected IO Inc. CONFIDENTIAL... - Page 12 Revision: V.05 Click on the “Play” button it will connect the Telit AT Controller to the serial port so communication can be established with the modem. Click on “AT terminal” button. P a g e | 12 Connected IO Inc. CONFIDENTIAL...
- Page 13 EMU CAT1 Modem User Manual Revision: V.05 The previous step will open AT terminal as shown below: P a g e | 13 Connected IO Inc. CONFIDENTIAL...
- Page 14 “Execute”. Figure 1 AT command responses, will be displayed in the terminal window on the right side of the Telit AT Controller software. Figure Figure 1: AT Command Example P a g e | 14 Connected IO Inc. CONFIDENTIAL...
-
Page 15: Apn Change
Note: Use cid=1 for NA units and cid=3 for VZ units. Examples: • AT+CGDCONT=1,”IPV4V6”,”<your APN name>” for NA units • AT+CGDCONT=3,”IPV4V6”,”<your APN name>” for VZ units Figure 2: APN Change P a g e | 15 Connected IO Inc. CONFIDENTIAL... - Page 16 EMU CAT1 Modem User Manual Revision: V.05 To verify the APN setting update was successful, enter AT command “AT+CGDCONT?” See Figure Figure 3: Check APN Function P a g e | 16 Connected IO Inc. CONFIDENTIAL...
-
Page 17: System Configuration - Linux
[ 515.960782] cdc_ncm 1-3:1.12 usb0: register 'cdc_ncm' at usb-0000:00:1a.7-3, CDC NCM, 00:00:11:12:13:14 The command response shows that Ubuntu, when connected to the module, maps automatically ttyACMx into USBx as summarized in Table 2 below. P a g e | 17 Connected IO Inc. CONFIDENTIAL... - Page 18 Networking connected to the Ethernet cable. The following screenshot shows that the Networking is disabled. Use the ifcongif command to display the status of the currently active network interfaces. P a g e | 18 Connected IO Inc. CONFIDENTIAL...
- Page 19 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) This command response shows that usb0 is the name of NCM interface, as stated before. P a g e | 19 Connected IO Inc. CONFIDENTIAL...
-
Page 20: Ncm Activation On The Module
#PORTCFG: Variant=4: not supported by this product #PORTCFG: Variant=5: not supported by this product #PORTCFG: Variant=6: not supported by this product #PORTCFG: Variant=7: not supported by this product #PORTCFG: Variant=8: AT= USB0 USB3 USB4; STT(Trace)= USB1 P a g e | 20 Connected IO Inc. CONFIDENTIAL... - Page 21 NOTE1: please note that for NA units, PDP context is usually set automatically at cid=1 NOTE2: please note that for Verizon units, PDP context is usually set automatically at • cid=3 AT+CGDCONT=4,"IP","APN" P a g e | 21 Connected IO Inc. CONFIDENTIAL...
- Page 22 AT#NCM command does not support User Name and Password. Modules equipped with an old software version, support only the command sequence a), and do not provide the AT#NCM command with User Name and Password. P a g e | 22 Connected IO Inc. CONFIDENTIAL...
-
Page 23: Pc Network Interface Configuration
8.8.8.8<enter> To use URL instead of IP addresses the DNS must be configured; modify the file /etc/resolv.conf adding the following line at the end of the file. nameserver 10.207.43.46 P a g e | 23 Connected IO Inc. CONFIDENTIAL... -
Page 24: Ncm Deactivation
Typical antenna Gain in most M2M applications should not exceed 2dBi. • At least 20cm of separation distance between the antennas, the collocated modem transmitters, and the human body must be maintained at all times. P a g e | 24 Connected IO Inc. CONFIDENTIAL... -
Page 25: Maximum Antenna Gain
Operating Temperature: -30°C to +85°C • Storage Temperature: -40°C to +85°C 8.2. Physical Parameters • Size: 84mm x 77mm x 17.8 • Weight: 60gr. 9. Approvals and Certifications 9.1. Manufacturing • RoHS Compliant P a g e | 25 Connected IO Inc. CONFIDENTIAL... - Page 26 Part 15 of the FCC Rules. • Canada CAN ICES-3 (B) / NMB-3 (B) This device Complies with ICES-003:2016 Issue 6, Class B. • Verizon Open Development Certification P a g e | 26 Connected IO Inc. CONFIDENTIAL...
Need help?
Do you have a question about the EM1000T-NA-CAT1 and is the answer not in the manual?
Questions and answers