Download Print this page

Honeywell IH25 Quick Start Manual

Uhf rfid reader
Hide thumbs

Advertisement

Quick Links

IH25
UHF RFID Reader
Quick Start Guide
IH25-EN-QSG REV B
05/2020

Advertisement

loading

  Also See for Honeywell IH25

  Related Manuals for Honeywell IH25

  Summary of Contents for Honeywell IH25

  • Page 1 IH25 UHF RFID Reader Quick Start Guide IH25-EN-QSG REV B 05/2020...
  • Page 2 Introduction The IH25 UHF RFID Reader provides Ultra High Frequency (UHF) Radio Frequency Identification (RFID) connected to a mobile terminal. The unit can read and write to bar code, QR code and UHF RFID tags. Bracket Socket Type C Port...
  • Page 3 Battery Installation and Remove Install the battery before using the reader for the first time. 1. To access the battery compartment, remove the battery cover screws and then the battery cover. 2. Insert the battery into the battery compartment with the tape at the bottom.
  • Page 4 Before using the reader for the first time, ensure the battery is fully charged. To charge the reader, use the USB cable + AC charge adapter (Honeywell recommended)or a docking station. Solid amber: Charging Solid green: Fully charged AC Charge...
  • Page 5 Docking Station Charge Use the one slot or four-slot docking station to charge IH25 and the mobile terminal. Note: when charging, make sure the charging indicator is always on. Power Power...
  • Page 6 Fitting/Unloading Device Case and Attaching Device Insert the mobile terminal into the bracket and press it down. Note: When installing the bracket, pay attention to the angle and strength so as not to damage the product. 2. Check the bracket on the bottom of the case and the socket on the reader are clean and free from dirt or debris.
  • Page 7 4. Unload the mobile terminal: place the IH25 on the table or hold it at the sides with both hands, push the buckle out with your thumbs, and lift the terminal out with your index finger. 5. Unload the bracket: hold the handle with one hand and lift it...
  • Page 8: Reading Rfid Tags

    QR Code Connect on the right top corner of Connect screen and select Barcode Way to scan the QR code on IH25 to pair with it. 2. Press MODE button and release within 3 seconds to check IH25’s operation mode. If RFID LED lights up, it means IH25 works in RFID mode;...
  • Page 9 Note The Barcode Way is only supported by Honeywell’s mobile • device. • Make sure to switch on the Bluetooth function and Location (Settings > Security & location> Location) on mobile before connecting. Otherwise, the connection fails all the time.
  • Page 10 MODE Button and Status Indicators MODE Press the MODE button to light on the current mode light. Release the button within 3 seconds, the mode light is off. MODE Press and hold the MODE button for at least 3 seconds to switch between 1D/2D and RFID mode and the current mode light is on.
  • Page 11: Important Safeguards

    Important Safeguards We recommend the use of Honeywell accessories and power adapters. Use of any non-Honeywell accessories or power adapters may cause damage not covered by the warranty. We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.
  • Page 12: User Documentation

    Support To search our knowledge base for a solution or to log into the Technical Support portal and report a problem, go to www.hsmcontactsupport.com. User Documentation For the user guide and other documentation, go to www.honeywellaidc.com. Limited Warranty For warranty information, go to www.honeywellaidc.com and click Get Resources >...
  • Page 13 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.