Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Xtracer Maxx
Summary of Contents for Xtracer Maxx
- Page 1 User Manual XC Tracer Maxx User Manual XC Tracer Maxx Rev 02 4.6.2020...
- Page 2 The vario is preset to beep only when flying. But you can set this as you wish. If you want to download the tracks or change the configuration file then connect XC Tracer Maxx to your computer with the included USB-C cable. Now switch on the vario and the SD card of XC Tracer Maxx will appear on the computer as a USB hard drive.
- Page 3 (due to data filtering). For this reason mount your XC Tracer Maxx in such a way that it moves as little as possible in relation to the harness during flight.
- Page 4 – gentle - medium – loud – mute – gentle etc. Energy Management A fully charged battery from the XC Tracer Maxx is sufficient to run the vario for up to 60 hours, including logging of IGC and KML files, sending and receiving of FLARM Beacons, data transfer over BLE etc.
- Page 5 Screens XC Tracer Maxx can display several predefined screens: • Simple • Standard • Thermal • Buddy • Airspace (Not yet ready) The LCD, which is perfectly readable in bright sunlight, has an update rate of 10Hz, so that a smooth display is guaranteed.
- Page 6 But as soon as the wind can be calculated, the wind is displayed, i.e. the arrow shows where the wind is blowing to. Even when soaring on a slope, XC Tracer Maxx can calculate the wind. The calculation of the wind usually works well to very well, but there can also be situations where this is not the case.
- Page 7 But please always keep an eye on the airspace around you and don't keep looking at the screen, however helpful it may be. It is best to try the thermal assistant when you are flying alone in a thermal. User Manual XC Tracer Maxx Rev 02 4.6.2020...
- Page 8 On the Buddy Screen you can see all paraglider and hang glider pilots who fly with a FLARM device and have been received by the XC Tracer Maxx in the last 5 minutes. Your position is in the middle of the circles, and from one circle to the next the distance (in kms) doubles.
- Page 9 If you want to add a buddy who also uses a variometer with FLARM at the launch site, it's very easy: Switch on the XC Tracer Maxx and the friend's vario, and wait until both varios have a GPS fix and you can start.
- Page 10 Connect XC Tracer Maxx to a computer using a USB-C Cable and once connected, switch the device on by briefly pressing the red button until you hear a beep-beep-beep. XC Tracer Maxx is now running in USB-MSD (Mass Storage Device) mode. XC Tracer Maxx’s internal Micro SD Card will appear as an external drive in Windows Explorer or the Mac Finder.
- Page 11 The sink tone will be activated when the sink rate is below -3m/s. SinkToneOffThreshold=-3.0 The sink tone will be deactivated when the sink rate is less than -3m/s. tone=-10.00,200,100,100 tone=-3.00,280,100,100 tone=-0.51,300,500,100 tone=-0.50,200,800,5 tone=0.09,400,600,10 tone=0.10,400,600,50 tone=1.16,550,552,52 tone=2.67,763,483,55 tone=4.24,985,412,58 tone=6.00,1234,332,62 tone=8.00,1517,241,66 tone=10.00,1800,150,70 User Manual XC Tracer Maxx Rev 02 4.6.2020...
- Page 12 XC Tracer Maxx doesn't actually save the new configuration into its internal memory until it starts up in normal flight mode. So, press the red button briefly to unmount / eject the device from your computer, disconnect it from the USB cable, then turn XC Tracer on as normal.
- Page 13 FLARM Obstacle Database / Collision Warning XC Tracer Maxx transmits your position twice per second and also your estimated trajectory for the next 20 seconds. Any other FLARM devices in the vicinity can use this information to assess any possible risk of collision.
- Page 14 Connect XC Tracer Maxx to a computer using a USB-C cable and once connected, switch the device on by briefly pressing the red button until you hear a beep-beep-beep. XC Tracer Maxx is now running in USB-MSD (Mass Storage Device) mode. XC Tracer Maxx’s internal Micro SD Card will appear as an external drive in Windows Explorer or the Mac Finder.
- Page 15 (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2AVOQ01 / Contains FCC ID: XPYANNAB User Manual XC Tracer Maxx Rev 02 4.6.2020...