Table of Contents
Advertisement
Quick Links
Add-on/Spare PCIe Card Instructions
This document describes how to add a PCIe card to or replace
an existing PCIe card in an Overland-Tandberg SnapServer
DX2.
WARNING:
To reduce the risk of electric shock or damage to
equipment, always remove any power cords while working with
the unit.
WARNUNG:
Um das Risiko eines elektrischen Schlags oder
Schäden am Gerät zu vermeiden, ziehen Sie stets den
Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT:
Pour réduire le risque de choc électrique
ou endommagement de l'équipement, retirez toujours les
cordons électriques en travaillant avec l'appareil.
CAUTION:
While working with the unit, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
Register a New PCIe Card
NOTE: If you are only replacing an existing PCIe card, skip ahead to
the next section,
"Prepare the Unit."
It is essential that the product be registered because technical
and warranty support is not available until then.
For an existing customer:
1. Go to
http://support.overlandstorage.com/
2. Enter your e-mail address and password, and then
press Enter or click the right arrow (>).
3. At the Support Home page, click Register New.
4. Enter the requested information and click Submit.
Your warranty certificate will be emailed to you. Follow
the instructions in the email to complete the process.
For a new customer, go to the
and follow the instructions.
Prepare the Unit
Power Off and Disconnect
If the unit is still running, power it down cleanly:
1. Use the Web Management Interface to power off the unit
(Maintenance > Shutdown/Restart > Shutdown).
2. When all the LEDs are off, disconnect the power cords.
3. Disconnect the remaining cables from the unit, noting
their locations.
10400357-002 11/2017
support page.
New User Registration
page
©2014-17 Overland Storage
NOTE: The Spare may come without the mounting bracket.
Reuse the existing bracket.
Existing User Login
Enter
New User Registration
Power Sockets
SnapServer
DX2
®
Enter
Enter
All Fields
Data Cables
Page 1 of 4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Overland Tandberg SnapServer DX2
Summary of Contents for Overland Tandberg SnapServer DX2
- Page 1 SnapServer ® Add-on/Spare PCIe Card Instructions This document describes how to add a PCIe card to or replace an existing PCIe card in an Overland-Tandberg SnapServer DX2. WARNING: To reduce the risk of electric shock or damage to equipment, always remove any power cords while working with the unit.
- Page 2 SnapServer DX2 Add-on/Spare PCIe Card Instructions Remove the Front Bezel 1. Carefully take hold of the front bezel and pull it straight out from the appliance until it releases. 2. Set the bezel aside on a secure surface. Remove the Drives IMPORTANT: Overland recommends that you remove all the drives to reduce the unit’s weight prior to rack removal.
- Page 3 SnapServer DX2 Add-on/Spare PCIe Card Instructions Replace the PCIe Card NOTE: If installing an additional PCIe card, go to “Install a New PCIe Card.” 1. At the rear (on top of the chassis wall), release and lift the bracket lock holding the cards in place.
- Page 4 SnapServer DX2 Add-on/Spare PCIe Card Instructions Reinstall the Carriers 1. Position the drive carrier in front of a drive bay. 2. Push the carrier in until the latch closes, locking the carrier in the drive bay. Repeat the procedure for each remaining drive carrier.
Need help?
Do you have a question about the SnapServer DX2 and is the answer not in the manual?
Questions and answers