Subscribe to Our Youtube Channel
Related Manuals for Ecraft EPS Pro Series
Summary of Contents for Ecraft EPS Pro Series
- Page 1 EPS-HDM1001 HDMI to DVBT Modulator ELECTROCRAFT AUSTRALIA 36 Binney Road, Marayong NSW 2148 T: (02) 8811 5155 F: (02) 9831 2139 www.electrocraft.com.au...
-
Page 2: Chapter 1 Introduction
EPS-HDM1001 Encoder Modulator User Manual Chapter 1 Introduction 1.1 Product Overview EPS-HDM1001 encoder & modulator is designed based on consumer electronics which allow audio/video signal input in TV distributions with applications in home entertainment, surveillance control, hotel Digital Signage, shops etc. It is an all-in-one device integrating MPEG2 encoding and modulating to convert audio/video signals into DVB-C/T/ATSC/ISDB-T RF out. - Page 3 EPS-HDM1001 Encoder Modulator User Manual Bit rate 1.000~20.000 Mbps Encoding MPEGI layer 2, AAC, AC3 Audio Sample rate 48KHz MPEGI layer 2: 192kbps Bit rate MPEGI layer 2 AAC: 18~297kbps AC3: 128kbps DVB-C Modulator Section Standard J.83A (DVB-C), J.83B ≥35dB RF frequency 100-1000MHz, 1KHz step RF output level...
-
Page 4: Appearance And Description
EPS-HDM1001 Encoder Modulator User Manual Upgrade Web update General Power supply DC 12V Dimensions 203*144*52mm Weight < 1kg 1.4 System Connection Samples 1.5 Appearance and Description... -
Page 5: Chapter 2 Installation Guide
EPS-HDM1001 Encoder Modulator User Manual Chapter 2 Installation Guide Ground Ground Safety Instructions WARNING: Hot plug is not allowed since it may cause system halted. To prevent fire or electrical shock, do not expose the device to rain or moisture. The network encoder is powered with a voltage of 12V DC. - Page 6 EPS-HDM1001 Encoder Modulator User Manual NO HOT PLUG! Connect the signal input in the respective connectors. The signal source can be from a surveillance monitor, DVD, set-top box, CCTV and etc. In case of connecting to a wired network, connect the encoder Ethernet port and terminal's Ethernet port with ethernet cable.
-
Page 7: Chapter 3 Web-Page Management
EPS-HDM1001 Encoder Modulator User Manual Chapter 3 Web-page Management Users cannot use front buttons to set configuration, and can only control and set the configuration in computer by connecting the device to web NMS Port. Users should ensure that the computer’s IP address is different from the EPS-HDM1001 IP address; otherwise, it would cause IP conflict. - Page 8 EPS-HDM1001 Encoder Modulator User Manual User can click any item here to enter the corresponding interface to check information or set the parameters. Figure-2 Function →: Encode &Modulate From the menu on left side of the webpage, clicking “Encoder & Module”, it displays the interface where users can configure the encoder parameters and select the modulating standard as Figure-3.
- Page 9 EPS-HDM1001 Encoder Modulator User Manual Figure-4 System →: Firmware From the menu on left side of the webpage, clicking “Firmware”, it will display the screen as Figure-5. Figure-5 System →: Password From the menu on left side of the webpage, clicking “Password”, it will display the screen as Figure-6 where to set the login account and password for the web NMS.
- Page 10 EPS-HDM1001 Encoder Modulator User Manual Figure-6 System →: Log From the menu on left side of the webpage, clicking “Log”, it will display the screen as Figure-7. Figure-7 Configuration: From the menu on left side of the webpage, clicking “Configuration”, it will display the screen as Figure-8.
- Page 11 EPS-HDM1001 Encoder Modulator User Manual Figure-8...
Need help?
Do you have a question about the EPS Pro Series and is the answer not in the manual?
Questions and answers