Advertisement
Tube Assembly: L18 / AG24EX, L24M*
AGHD28, L28M* or IG30M*
Twist, Lock and Hold EACH Tube Join before installing first screw.
Min. Insertion: L18/AG24EX & L24M* = 13"
80" end tube
L18/AG24EX
Maximum Extension 24'6" (7
or
L24M*
** Extra hardware and instructions are inside extension tube.
(5 tube Configuration)
Min. Insertion: L28M* = 17" & AGHD28 = 9"
end tube
L28M* or AGHD28
Maximum Extension 28'6" (8.6 m). Maximum Cover Weight 50# (22.7kg)
** Extra hardware, instructions are included in tube set carton.
Min. Insertion 20"
90" end tube
IG30M*
Maximum Extension 30'6" (9.3 m) Round Pools. Maximum Cover Weight 50# (22.7kg)
** Extra hardware, instructions are included in tube set carton.
*
Mill tubes may tarnish over time. This does not affect performance or Warranty. Anodized tubes help reduce tarnishing.
STEP 3: ASSEMBLE ENDS
Assemble in numerical order (see Fig. 7):
Insert #1 appropriate sized Plug into End Tube.
Place #2 Bearing inside #3 Tee.
Push #4 Handle through Bearing and into Plug.
Insert #5 self-drilling screw through tube in line with
bump (Long Prong) on plug rim and 1" (2.5 cm) from
tube end.
Repeat for other end.
STEP 4: STRAP ATTACHMENT
Attach a Strap Plate to one
end of all Straps provided
(see Fig. 8).
Strap length can be adjusted at
Strap Plate if necessary.
STRAP ATTACHMENT - TO TUBES
A.
Mark each End Tube 6" (15 cm) in from the inside edge of pool
top rail. Attach one Strap at each mark on a Drill Line (see Fig. 9).
The remainder of the Straps will be spaced evenly - on Drill Lines
- between the outside 2 Straps.
Mark all strap locations before installing. Use all Straps provided.
Note: Maximum distance between straps is 30"
Attach Straps to Tubes at the marks with a Metal Screw directly
B.
through the strap material and approximately 1" back from the
end of the strap (see Fig. 9). DO NOT pre-drill holes (a tiny "pilot
hole" is acceptable) or over-tighten screw.
(new 5 Tube Configuration)
(Butt Center Tubes)
19" joiner tube
80" center tube
.
47 m). Maximum Cover Weight 50# (22.7kg)
(Butt center tubes)
center tube
Min. Insertion 20"
90"center tube
Plugs:
1. FG-PLG
(31/2" diam. Tube)
FG-PLGL (3" diam. Tube,
"L" Series)
Attach this end to Tube
Strap end
,
Assembly for Tubesets below require a total of
24 SELF-DRILLING stainless steel screws.
(6 Screws at EACH Tube Join).
DO NOT pre-drill holes or over-tighten screws.
A very small "pilot hole" is acceptable.
(2 Tube Joins)
Min. Insertion: L18/AG24EX & L24M* = 13"
80" center tube (Extension tube)
Min. Insertion: L28M* = 17" & AGHD28 = 9"
joiner tube
center tube (Extension tube)
Min. Insertion 20"
90" end tube
90" center tube
OR
FG-614 - Cone
Strap end
Strap
80" end tube
end tube
Min. Insertion 20"
90" end tube
Fig. 6
IMPORTANT
Insert (#5) self-drilling screw through
tube in line with bump on plug
rim (Long Prong) and 1" (2.5 cm)
from tube end. (at BOTH ends)
FG-TEE
FG-BEA005 - Bearing
Fig. 7
FG-B-HAN - Handle
Attach this end
to Blanket with
Plastic Screw
Strap Plate
(Side View)
Fig. 8
Metal Self-Drilling
Screw
Attach Straps
approx. 1"
from Strap
End -
on Tube
Tube
Drill Lines
Fig. 9
Strap
Advertisement
