Related Manuals for Factor Electronics HDBaseT
Summary of Contents for Factor Electronics HDBaseT
- Page 1 HDBaseT-4x4Matrix HDBaseT-4x4-Matrix HDCP 2.2 HDBaseT Lite 4x4 HDMI Matrix w/ Audio Breakouts 4159 McConnell Drive Burnaby B.C. Canada V5A-3J7 Toll Free 1-855-204-1388 www.factorelectronics.com Factor Electronics...
- Page 3 5. To reduce the interference among the unshielded twisted pairs of wires in CAT cable, do not Factor Electronics will not repair or replace a module that is shipped in such a way that the product run HDBaseT / Zone Cat5e/6/6a cabling with or in close parallel proximity to mains power is not properly protected.
-
Page 4: Table Of Contents
RMA Policy ........................... 23 Standard Replacement ......................23 In the event the product returned to Factor Electronics has been discontinued (i.e. the product is no Once you have obtained an RMA number ................24 longer being manufactured by Factor Electronics but is still under warranty), Factor Electronics will, Please note ........................... -
Page 5: Introduction
Embedded audio extractors can extract the audio and output via L/R or Coaxial. Volume can be controlled for analog audio out. Based on the HDBaseT Lite chipset the output distance can reach up to 70m via Cat5e/6.Each source can be routed to any display using the Push Buttons, IR... -
Page 6: Back Panel
HDBaseT-4x4Matrix HDBaseT-4x4Matrix INPUT VIDEO AUDIO EDID Page Note 1080I 2.0CH. You can select built-in EDID patterns for each input, and select EDID priority for HDMI/HDBT. 1080P 5.1CH 7.1CH D1024 D1024=DVI 1024 x 768 D1080 D1080=DVI 1920 x 1080 D1200 D1200=DVI 1920 x 1200... -
Page 7: Remote Control Description
12. HDMI outputs 1 to4 -- Output to four displays, AVR etc. 13. IR extension receiver input -- 3.5mm stereo phone-jack, connects to the IR receiver cable to receive the IR from the HDBaseT-4x4Matrix remote. 14. Power port -- Use the included 24V/3.5ADC adaptor to power the matrix. -
Page 8: Satellite Remote Control
Satellite Remote Control Application Diagram Output Page You can select Input for each Output, enable/disable each Output and set the priority for HDMI/HDBaseT outputs This page also shows the connect status for HDMI/HDBaseT ports. Specifications Bandwidth 10.2Gbps Video Input Connectors... -
Page 9: Package Contents
HDBaseT-4x4Matrix HDBaseT-4x4Matrix Zone Page Package Contents Same as Guest account interface 1x HDbaseT-4x4Matrix 1x 24V/3.5A DC Power Supply 1x Power Cord 1x Master Remote Control 4x Satellite Remote Control 4x IR Transmitter 5x IR Receiver 1x RS232 (DB9) to Phoenix Terminal Cable... - Page 10 HDBaseT-4x4Matrix HDBaseT-4x4Matrix Web GUI Reset System To Default Setting, RESET Should Type „Yes‟ To Confirm, „No‟ To Discard How to enter the Web GUI OUT xx ON/OFF Set OUTPUT:xx On Or Off Type in the IP address "192.168.0.200" in your web browser to enter the Web GUI. The first login...
-
Page 11: Gui Control
HDBaseT-4x4Matrix HDBaseT-4x4Matrix “FW upgrade” page GUI Control PC System: Microsoft Windows Operation System Installation The HDBaseT4x4 Matrix software controller is green software.Simplycopy the “4x4 HDMI Matrix Controller vx.x.exe” to yourPC which is used to control the Matrix by connecting an RS232 COM or TCP port to complete the installation. -
Page 12: Set Tcp Control Configuration
HDBaseT-4x4Matrix HDBaseT-4x4Matrix ① Select control mode: RS232 COM mode (Auto COM ports detected) or TCP mode Memory/User2 Memory first. The User1/User2 default EDID content is 1080p, Stereo Audio 2.0. ② List detected COM ports ② Copy the EDID from an Output port to a selected Input port or All Input ports, click the “Copy”... -
Page 13: Port Tag" Page
HDBaseT-4x4Matrix HDBaseT-4x4Matrix “1 Output” to “4 Outputs”: Set the current Output (right click the mouse) and the next x-1 (x range is “Port Tag” page from 1 to 4, set total x Outputs at the same time) all Output(s) from the same Input Port to Port: Output1 from Input1, Output2 from Input2, Output3 from Input3, etc. -
Page 14: Setting" Page
HDBaseT-4x4Matrix HDBaseT-4x4Matrix Click buttons with “×” caption to delete the tag that you want to delete, if a tag is still used by any selection status of the Output port. other Input port, the delete action will be discarded. Pop-up tag messages When the “Display Input, Output tags setting buttons are on”...
Need help?
Do you have a question about the HDBaseT and is the answer not in the manual?
Questions and answers