1. Manuals
  2. Brands
  3. Data Aire Manuals
  4. Computer Hardware
  5. DAP III
  6. Integration information

Data Aire DAP III Integration Information

Snmpv1/v2c protocol
Hide thumbs Also See for DAP III:
Table of Contents

Advertisement

Quick Links

Download this manual
Data Aire DAP III
SNMPv1/v2c
Protocol Integration Information
Data Aire, Inc.
230 West Blueridge Avenue
Orange, California 92865
Document Number 600-000-615
November 2010
Revision 3.0
Document 600-000-615
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DAP III and is the answer not in the manual?

Questions and answers

Related Manuals for Data Aire DAP III

Summary of Contents for Data Aire DAP III

  • Page 1 Data Aire DAP III SNMPv1/v2c Protocol Integration Information Data Aire, Inc. 230 West Blueridge Avenue Orange, California 92865 Document Number 600-000-615 November 2010 Revision 3.0 Document 600-000-615...

  • Page 2: Table Of Contents

    ....................... 5 Sending Traps on Alarms ....................5 MIB (Management Information Base) file ..............5 SNMP Object Definitions for DAP III ................5 Control Module Status (Read Only) .................. 5 Control Module Control (Read/Write)................9 Control Module Configuration (Read/Write) ..............10 Control Module Configuration (Read Only)..............

  • Page 3: Overview

    ID and to menu 6-2 –Network protocol to configure the network protocol. Menu 6-2 to 6-7 are locked menus, refer to the DAP III Operation Manual for the procedure of how to unlock these menus before entering IP address. It is recommended to reset the DAP III panel after changing the network protocol, IP adress or the unit ID number.

  • Page 4: Network Wiring

    2.3 Network Wiring 2.3.1 For the Ethernet connection, Use the CAT-5 Ethernet cable. The DAP III panel should be connected to the same network with the monitoring PC or BMS. See figure 3 for details. Each unit requires having a dedicated IP address. Consult with the building IT personnel or building network administrator on IP addressing.

  • Page 5: Communication Port Setting

    3 Communication Port Setting For SNMP communication UDP port setting is 161, refer to the DAP III Operation Manual for the procedure to enter an IP address and port setting to the DAP III. 4 Community Data string The Data Aire DAP III SNMP community data string is default to “public”.
  • Page 6 Object Identifier Type Description Units on(non-zero) 1.3.6.1.4.1.22731.1.2.1.5.0 INTEGER Heating Held off(0) Heating is in inhibited mode on(non-zero) 1.3.6.1.4.1.22731.1.2.1.6.0 INTEGER Humidification Held off(0) Humidification is in inhibited mode on(non-zero) 1.3.6.1.4.1.22731.1.2.1.7.0 INTEGER Dehumidification Held off(0) Dehumidification is inhibted on(non-zero) 1.3.6.1.4.1.22731.1.2.1.8.0 INTEGER Reheating During Dehumidification off(0) Heating is on during dehumidification mode on(non-zero)
  • Page 7 No air flow: Check belt and motor off(0) Standard alarm on(non-zero) 1.3.6.1.4.1.22731.1.2.1.28.0 INTEGER Dirty filter: Check filters off(0) Standard alarm on Data Aire series, optional on on(non-zero) ceiling units 1.3.6.1.4.1.22731.1.2.1.29.0 INTEGER Humidifier problem: Check water pressure off(0) Standard alarm on Data Aire series, optional on...
  • Page 8 Object Identifier Type Description Units 1.3.6.1.4.1.22731.1.2.1.41.0 INTEGER Smoke detector: Unit shutdown off(0) Optional alarm. An optional smoke detector on(non-zero) required 1.3.6.1.4.1.22731.1.2.1.42.0 INTEGER No water flow: Check pump off(0) Optional alarm. An optional flow switch on(non-zero) required 1.3.6.1.4.1.22731.1.2.1.43.0 INTEGER Discharge temperature sensor problem off(0) Optional alarm.

  • Page 9: Control Module Control (Read/Write)

    Object Identifier Type Description Units 1.3.6.1.4.1.22731.1.2.1.58.0 INTEGER Custom alarm #4 off(0) Optional alarm. External alarm input required on(non-zero) Factory programmed custom message required 1.3.6.1.4.1.22731.1.2.1.59.0 INTEGER Humidification inhibited off(0) Optional alarm. External alarm input required. on(non-zero) Humidification is inhibited when alarm goes off. 1.3.6.1.4.1.22731.1.2.1.60.0 INTEGER Reheat inhibited...

  • Page 10: Control Module Configuration (Read/Write)

    Network Variable Network Variable Type Description Units Unit off (1) BMS or BAS Unit standby(2) 7.3 Control Module Configuration (Read/Write) Network Variable Network Variable Type Description Units 1.3.6.1.4.1.22731.1.2.1.72.0 INTEGER (0..59) Time of Day: Seconds 1.3.6.1.4.1.22731.1.2.1.73.0 INTEGER (0..59) Time of day: Minutes 1.3.6.1.4.1.22731.1.2.1.74.0 INTEGER (0..23) Time of day: Hours...
  • Page 11 Network Variable Network Variable Type Description Units 1.3.6.1.4.1.22731.1.2.1.94.0 DisplayString Custom Alarm Message 3 (SIZE (0..40)) Optional factory programmed alarm message. 1.3.6.1.4.1.22731.1.2.1.95.0 DisplayString Custom Contact (SIZE (0..25)) Optional factory programmed contact information. 1.3.6.1.4.1.22731.1.2.1.96.0 INTEGER (0..5) Adjustment rate Minutes 1.3.6.1.4.1.22731.1.2.1.97.0 INTEGER (0..900) Optional Alarm 1 Delay Seconds 1.3.6.1.4.1.22731.1.2.1.98.0...
  • Page 12 Network Variable Network Variable Type Description Units two-with-limits(3) one-no-limits(4) two-no-limits(5) 1.3.6.1.4.1.22731.1.2.1.107.0 INTEGER Heater Configuration none(1) Factory setting one-heat-strip(2) two-heat-strips(3) three-heat-strips(4) hot-water(5) 1.3.6.1.4.1.22731.1.2.1.108.0 INTEGER Humidifier Configuration none(1) Factory setting computer-non-modutating(2) computer-modulating(3) comfort-non-modulating(4) comfort-modulating(5) 1.3.6.1.4.1.22731.1.2.1.110.0 INTEGER Lead-Lag Configuration auto(1) one-leads(2) two-leads(3) three-leads(4) four-leads(5) 1.3.6.1.4.1.22731.1.2.1.111.0 INTEGER (0..1000)

  • Page 13: Control Expansion Module Status (Read Only-Optional)

    7.5 Control Expansion Module Status (Read Only-Optional) Note: these points do not apply to Mini-DAP III panel Object Identifier Type Description Units 1.3.6.1.4.1.22731.1.2.2.1.0 INTEGER Control Expansion Module Installed not installed(0) installed(non-zero) 1.3.6.1.4.1.22731.1.2.2.2.0...

  • Page 14: Control Expansion Module Configuration (Read/Write-Optional)

    Optional discharge air temperature sensor required 1.3.6.1.4.1.22731.1.2.2.11.0 INTEGER Chilled Water Temperature Sensor Calibration 0.1°F Optional chilled water temperature sensor required 7.6 Control Expansion Module Configuration (Read/Write-Optional) Note: these points do not apply to Mini-DAP III panel Object Identifier Type Description Units 1.3.6.1.4.1.22731.1.2.2.12.0 INTEGER (45..61) Low Discharge Temp Limit °F...

  • Page 15: Relay Module Status (Read Only-Optional)

    2-10 VDC(5) 1.3.6.1.4.1.22731.1.2.2.20.0 INTEGER Reverse Water Valve Configuration normal(1) Factory setting reverse(2) 7.8 Relay Module Status (Read Only-Optional) Note: these points do not apply to Mini-DAP III panel Object Identifier Type Description Units 1.3.6.1.4.1.22731.1.2.3.1.0 INTEGER Relay Module Installed not installed(0)

  • Page 16: Analog Module Status (Read Only-Optional)

    Note: all the objects in this section are optional. They require an Analog module to be installed onto the DAP III panel and optional analog transducers or transmitters required. Refer to the DAP III O&M manual for Analog Module configuration and programming. Object Identifier...
  • Page 17 Object Identifier Type Description Units input-current-c(10) output-current-a(11) output-current-b(12) output-current-c(13) neutral-current(14) ground-current(15) frequency(16) power(17) cond-water-supply-temp(18) cond-water-return-temp(19) chill-water-supply-temp(20) chill-water-return-temp(21) supply-air-temp(22) return-air-temp(23) cond-water-flow(24) chill-water-flow(25) zone-air-temp(26) zone-air-humidity(27) outside-air-temp(28) outside-air-humidity(29) discharge-pressure(30) suction-pressure(31) diff-pressure(32) pressure(33) flow(34) 1.3.6.1.4.1.22731.1.2.4.9.0 INTEGER Analog Sensor 1 Units VAC(1) amps(2) Hz(3) kW(4) degrees F(5) degrees C(6) gpm(7)
  • Page 18 Object Identifier Type Description Units input-current-b(9) input-current-c(10) output-current-a(11) output-current-b(12) output-current-c(13) neutral-current(14) ground-current(15) frequency(16) power(17) cond-water-supply-temp(18) cond-water-return-temp(19) chill-water-supply-temp(20) chill-water-return-temp(21) supply-air-temp(22) return-air-temp(23) cond-water-flow(24) chill-water-flow(25) zone-air-temp(26) zone-air-humidity(27) outside-air-temp(28) outside-air-humidity(29) discharge-pressure(30) suction-pressure(31) diff-pressure(32) pressure(33) flow(34) 1.3.6.1.4.1.22731.1.2.4.15.0 INTEGER Analog Sensor 2 Units VAC(1) amps(2) Hz(3) kW(4) degrees F(5) degrees C(6)
  • Page 19 Object Identifier Type Description Units input-current-a(8) input-current-b(9) input-current-c(10) output-current-a(11) output-current-b(12) output-current-c(13) neutral-current(14) ground-current(15) frequency(16) power(17) cond-water-supply-temp(18) cond-water-return-temp(19) chill-water-supply-temp(20) chill-water-return-temp(21) supply-air-temp(22) return-air-temp(23) cond-water-flow(24) chill-water-flow(25) zone-air-temp(26) zone-air-humidity(27) outside-air-temp(28) outside-air-humidity(29) discharge-pressure(30) suction-pressure(31) diff-pressure(32) pressure(33) flow(34) 1.3.6.1.4.1.22731.1.2.4.21.0 INTEGER Analog Sensor 3 Units VAC(1) amps(2) Hz(3) kW(4) degrees F(5)
  • Page 20 Object Identifier Type Description Units output-voltage-a-c(6) output-voltage-b-c(7) input-current-a(8) input-current-b(9) input-current-c(10) output-current-a(11) output-current-b(12) output-current-c(13) neutral-current(14) ground-current(15) frequency(16) power(17) cond-water-supply-temp(18) cond-water-return-temp(19) chill-water-supply-temp(20) chill-water-return-temp(21) supply-air-temp(22) return-air-temp(23) cond-water-flow(24) chill-water-flow(25) zone-air-temp(26) zone-air-humidity(27) outside-air-temp(28) outside-air-humidity(29) discharge-pressure(30) suction-pressure(31) diff-pressure(32) pressure(33) flow(34) 1.3.6.1.4.1.22731.1.2.4.27.0 INTEGER Analog Sensor 4 Units VAC(1) amps(2) Hz(3)
  • Page 21 Object Identifier Type Description Units 1.3.6.1.4.1.22731.1.2.4.35 INTEGER Constant Fan Speed – DX 1.3.6.1.4.1.22731.1.2.4.36 INTEGER Constant Fan Speed - CW 1.3.6.1.4.1.22731.1.2.4.37 INTEGER Fan Speed Control – DX 1.3.6.1.4.1.22731.1.2.4.38 INTEGER Fan Speed Control – CW 1.3.6.1.4.1.22731.1.2.4.39 INTEGER Maximum Fan Speed 1.3.6.1.4.1.22731.1.2.4.40 INTEGER Minimum Fan Speed 1.3.6.1.4.1.22731.1.2.4.41 INTEGER...

Table of Contents