Advertisement
location.
Do not store a spare LP gas tank under or
near this appliance.
Use protective gloves when assembling this
product.
Do not force parts together as this can
result in personal injury or damage to the
product.
Do not operate lantern with a hole or crack
in the mantle.
Do not attempt to operate the lantern
without a mantle installed.
Deaths, serious injury or damage to
property may occur if the above is not
followed exactly.
Operating Instructions
Lantern is inteded to hang from the chain on a non-
combustable, sturdy support, unless lantern is used
with optional base (part number 55-09-287, not
included).
This lantern is designed to operate with a one pound
7-3/8" high disposable / 16.4 oz. propane gas tank
(DOT 39 Cylinder).
DO NOT ATTEMPT TO REFILL ANY ONE POUND
(16.4 oz.) PROPANE GAS TANKS!
Connecting Gas Tank
1. Make sure the control knob is in the "OFF" position.
(Figure 1)
2. Lubricate the threads of the regulator valve
with petroleum jelly, insert the gas tank into the
regulator valve and hand-tighten firmly. (Figure 2)
3. Insert LP gas tank into the base.
4. Test for leaks
Checking for Leaks
WARNING: Failure to inspect this connection or
follow these instructions could cause a fire or
an explosion which can cause death, serious
bodily injury, or damage to property.
1. Make 2-3 oz. of leak solution by mixing one part
liquid dishwashing soap with three parts water.
2. Make sure control knob is "OFF".
3. Attach LP gas tank, per "Connecting Gas Tank"
instructions.
4. Spoon several drops of solution, or use squirt
bottle, at the LP gas tank to regulator connection.
5. Inspect the solution at the connections, looking for
bubbles or the smell of rotten cabbage.
a. If NO bubbles appear or smells of rotten
cabbage, the connections are secure.
b. If bubbles appear, you have a leak.
1. Loosen and retighten this connection, making
sure the connection is secure.
2. Retest with solution.
If you continue to see bubbles after several
attempts, disconnect propane source and
contact 1.800.762.1142 for assistance.
Lighting
DO NOT expose the lantern to flammable
vapors or liquids during lighting.
1. Make sure all labels, packaging and protective
films have been removed from the lantern.
2. Make sure there are no obstructions of airflow to
the gas unit. Spiders and insects can nest within
and clog the burner / venturi tube at the orifice.
Figure 1
Figure 2
Figure 3
Match
A clogged burner tube can lead to a fire.
3. Control knobs must be in the "OFF" position.
(Figure 1)
4. Attach the LP gas tank per the "Connecting Gas
Tank" instructions.
5. Igniter: Turn the control knob counterclockwise
to "ON" and repeatedly push the igniter button to
ignite the mantle.
Match: Wearing heat reistant gloves, position the lit
long match or lit long butane lighter evenly next to
the mantle. (Figure 3)
a. Turn control knob counterclockwise to "ON".
b. Hold lit long match or lit long butane lighter next
to mantle for up to 5 seconds.
c. Remove long match/long butane lighter.
d. Replace cap.
Note: Once the mantle has been burned, it is very
fragile. Be careful not to touch it with finger or
match.
6. If ignition does not occur in 5 seconds, turn burner
control knob "OFF", wait 5 minutes and repeat
lighting procedure.
Caution: If burner flame goes out during
operation, immediately turn the gas "OFF" and
let the gas clear for about 5 minutes before
re-lighting.
Turning Off
1. Turn control knobs to the "OFF" position.
2. Allow lantern to completely cool.
3. Remove LP gas tank and properly store tank.
English – 3
Transporting
While Lantern is ON
1. Carefully carry the lantern by the chain.
2. Do not touch any of the lantern surfaces as they
may be hot
3. Before setting the lantern down, make sure the
lantern is hanging from a sturdy, non-combustable
support or the tank is properly in the base.
While Lantern is OFF
1. The LP gas tank must be removed and stored
properly.
2. Once the lantern is cooled, place the lantern (and
optional base) in a plastic bag and secure the bag
with a string.
DO NOT COMPLETELY SEAL THE PLASTIC BAG.
Note: The plastic bag will help protect from insects.
Replacing Mantle
1. Turn control knob to "OFF" and remove LP
gas tank.
2. Allow lantern to cool completely.
3. Open cap and remove globe
4. Attach mantle
Note: Tie the mantles around grooves in burner.
Note: Evenly distribute folds on mantle. Cut off the
extra string.
5. Insert globe and close cap
6. Perform leak check
Cleaning and Care
CAUTION: All cleaning and maintenance should
be done when lantern is cool and with the fuel
supply disconnected.
CAUTION: DO NOT clean any lantern part in
a self cleaning oven. The extreme heat will
damage the finish.
CAUTION: Keep lantern clear and free from
combusitble materials, gasolline and other
flammable vapours and liquids.
CAUTION: Do NOT obstruct the flow of
combustion and ventilation air.
Notices
1. Abrasive cleaners will damage this product.
2. Never use oven cleaner to clean any part of
lantern.
Inspecting
This lantern should be inspected on a regular basis to
ensure product safety and longer product life.
WARNING: Do NOT attempt to clean this lantern
unless the flames are COMPLETELY out and
unit is cool to the touch, about 45 minutes.
1. Check burner to make sure it is secure.
2. Check valve to make sure it is clear and free of
spider nests.
3. Check all gas connections for leaks.
4. Check components for any signs of damage or rust.
5. If damage to any component is detected, do NOT
operate until repairs are executed.
Cleaning Surfaces
WARNING: Do NOT attempt to clean this lantern
unless the flames are COMPLETELY out and
unit is cool to the touch. (About 45 minutes).
WARNING: Do NOT use oven cleaner or abrasive
cleaners as they will damage this product.
1. Wipe surfaces clean with mild dishwashing
detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser
and a nylon scrubbing brush.
3. Rinse clean with water.
Product Registration
For faster warranty service, register your product
immediately at www.bluerhino.com or call
1.800.762.1142.
Limited Warranty
Blue Rhino Global Sourcing, Inc ("Vendor") warrants
to the original retail purchaser of this product, and to
no other person, that if this product is assembled and
operated in accordance with the printed instructions
accompanying it, then for a period of one (1) year from
the date of purchase, all parts in such product shall
be free from defects in material and workmanship.
Vendor may require reasonable proof of your date
of purchase. Therefore, you should retain your sales
slip or invoice. This Limited Warranty shall be limited
to the repair or replacement of parts, which prove
defective under normal use and service and which
Vendor shall determine in its reasonable discretion
upon examination to be defective. Before returning any
parts, you should contact Vendor's Customer Service
Department using the contact information listed below.
If Vendor confirms, after examination, a defect covered
by this Limited Warranty in any returned part, and if
Vendor approves the claim, Vendor will replace such
defective part without charge. If you return defective
parts, transportation charges must be prepaid by you.
Vendor will return replacement parts to the original
retail purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or
operating difficulties due to accident, abuse, misuse,
alteration, misapplication, improper installation or
improper maintenance or service by you or any
third party, or failure to perform normal and routine
maintenance on the product as set out in this owner's
English – 4
Advertisement
