Advertisement
Available languages
Available languages
Some of the above types of operations require special
accessories that are not included in the delivery scope
and not described in this manual�
Power tool components
1 Chuck HEX-30
2 Retainer
3 Clamping handle *
4 Additional handle *
5 Ventilation slots
6 On / off switch
7 Power indicator
8 Carbon brush replacement indicator
9 Tube with lubricant *
10 Locking screw of additional handle *
11 Washer *
12 Bolt *
13 Nut *
14 Screw of outer cover
15 Outer cover
16 Inner cover
17 Felt plug
18 Lubrication hole
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Additional handle (see fig. 1-2)
Always use the additional handle 4 when operating�
Additional handle 4 may be positioned as deemed
comfortable by the user�
Mounting / dismounting of additional handle (see
fig. 1)
• Install bolt 12 as shown in fig. 1.1.
• Install nut 13 in clamping handle 3 as shown in fig. 1.1.
• Install additional handle 4 and tighten clamping han-
dle 3 (see fig. 1.2).
• Screw in locking screw 10 in the axial hole of the
bolt 12� This will prevent the spontaneous loosening of
clamping handle 3�
• Disassembly operations do in reverse sequence�
Installing the additional handle in more comfort-
able position (see fig. 2)
• Loose screw 10�
• Loose clamping handle 3 as shown in fig. 2.
• Place additional handle 4 in desired position�
• Tighten clamping handle 3�
• Tighten screw 10�
Mounting / replacement of accessories (see fig. 3)
• Release the retainer 2 as shown in figure 3.1.
• Install / replace the working accessory in the chuck�
When installing the working accessory, it is necessary
to clear the shank end preliminarily� Install the acces-
sory only as shown in the figure: the groove on the
accessory must face the retainer 2�
• Lock the retainer 2 as shown in figure 3.2.
Gloves are to be used when removing
the chisel from chuck 1 (HEX-30), as the
chisel may be dangerously hot after long
work.
Initial operating of the power tools
• Always use the correct supply voltage the power
supply voltage must match the information quoted on
the power tool identification plate.
• The power tool is supplied properly lubricated and
ready for use�
• A new power tool needs some time for its parts to
run in before a full load operation� The run-in period
duration is about 5 hours of operation�
• The gear lubrications require a short time to get
warm� Depending on the ambient temperature this
period of time can alter within the range of approxi-
mately 15 s (at ambient temperature of 32°С) up to 2
minutes (at ambient temperature of 0°С).
Switching the power tool on / off
Switching on:
Move on / off switch 6 to the right until it stops (see
fig. 4.1).
Switching off:
Move on / off switch 6 to the left until it stops (see
fig. 4.2).
Design features of the power tool
Vibration protection system
The vibration protection system is design to reduce vi-
bration impact (during operation) on the operator�
Power indicator
Power indicator 7 is on when the power tool is con-
nected to the mains and is ready to be switched on�
Carbon brush replacement indicator
Carbon brush replacement indicator 8 - signals about
need to replace the carbon brushes�
Recommendations on the power tool
operation
Wear thick soft gloves when working to
reduce vibration impact on your body.
English
18
Advertisement
