Page 1
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
Page 2
ES1000-Ethernet-ug-en.book Seite 1 Freitag, 19. Januar 2001 5:12 17 Network Installation for ES1130 and ES1120 User’s Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 3
Copyright The data in this document may not be altered or amended without special notification from ETAS GmbH. ETAS GmbH undertakes no further obligation in relation to this document. The software described in it can only be used if the customer is in possession of a general license agreement or single license.
ES1000-Ethernet-ug-en.book Seite 5 Freitag, 19. Januar 2001 5:12 17 Introduction This guide tells you how to install and configure your PC’s network interface to connect it to the ES1130 and ES1120. The guide contains the following: • Introduction (this chapter) •...
Page 7
ES1000-Ethernet-ug-en.book Seite 6 Freitag, 19. Januar 2001 5:12 17 Introduction Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
This guide describes the installation of the ’XIRCOM RealPort2 CardBus Ether- net 10/100’ network adapter. The description also applies to the installation of other manufacturers’ network adapters. ETAS recommends using the ’XIRCOM RealPort2’ because of its high perfor- mance (100 MBit Ethernet, 32-bit PC-card interface) and its good mechanical properties.
ES1000-Ethernet-ug-en.book Seite 8 Freitag, 19. Januar 2001 5:12 17 BIOS Update for Notebooks Problems have been reported concerning the cooperation of modern PCMCIA/ CardBus PC cards and the BIOS of older notebooks. We therefore recommend updating your notebook’s BIOS to the latest version. More information can be found on the relevant manufacturer’s homepage.
ES1000-Ethernet-ug-en.book Seite 9 Freitag, 19. Januar 2001 5:12 17 Installation and Configuration for Windows 9x This chapter describes the installation of the network adapters and the config- uration of the TCP/IP protocol for Microsoft Windows 9x. If a network card already installed is to be replaced by a new one, you must remove the old card first.
ES1000-Ethernet-ug-en.book Seite 10 Freitag, 19. Januar 2001 5:12 17 1. Plug in the new card and switch on the PC. Normally, Windows 9x automatically detects your network adapter. If the automatic detection does not work, choose a new network adapter manually.
Page 12
ES1000-Ethernet-ug-en.book Seite 11 Freitag, 19. Januar 2001 5:12 17 2. The settings in the Driver Type, Bindings and Advanced tabs are as follows: Installation and Configuration for Windows 9x Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 13
ES1000-Ethernet-ug-en.book Seite 12 Freitag, 19. Januar 2001 5:12 17 Installation and Configuration for Windows 9x Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
ES1000-Ethernet-ug-en.book Seite 13 Freitag, 19. Januar 2001 5:12 17 Configuring the Network Protocol 1. Select the TCP/IP protocol bound to the network adapter card for the ES1000 from the list of installed network components and click Proper- ties. The TCP/IP Properties dialog box opens. 2.
Page 15
ES1000-Ethernet-ug-en.book Seite 14 Freitag, 19. Januar 2001 5:12 17 – Bindings – Advanced Installation and Configuration for Windows 9x Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 16
ES1000-Ethernet-ug-en.book Seite 15 Freitag, 19. Januar 2001 5:12 17 – NetBIOS – DNS: use the settings of your LAN (if no LAN connection is present, DNS can be disabled). Installation and Configuration for Windows 9x Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 17
ES1000-Ethernet-ug-en.book Seite 16 Freitag, 19. Januar 2001 5:12 17 – Gateway: no gateway required – WINS: use the settings of your LAN (if no LAN connection is present, WINS can be dis- abled). Installation and Configuration for Windows 9x Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 18
ES1000-Ethernet-ug-en.book Seite 17 Freitag, 19. Januar 2001 5:12 17 – IP address If a second network adapter card for the LAN has to be configured, proceed as described above. Ask your administrator for the correct settings. If you have already removed an adapter card for the LAN, enter the old settings. An overview of all network settings is given in the section "Configuration Parameters for TCP/IP"...
Page 19
ES1000-Ethernet-ug-en.book Seite 18 Freitag, 19. Januar 2001 5:12 17 Installation and Configuration for Windows 9x Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
ES1000-Ethernet-ug-en.book Seite 19 Freitag, 19. Januar 2001 5:12 17 Installation and Configuration with NT 4.0 This chapter describes the installation of network adapter cards and the con- figuration of the TCP/IP protocol for Windows NT 4.0. If a network card already installed is to be replaced by a new one, you must remove the old card first.
ES1000-Ethernet-ug-en.book Seite 20 Freitag, 19. Januar 2001 5:12 17 Installing a Network Adapter Card 1. Plug in the new card and switch on the PC. 2. To open the Network properties dialog box, choose → → Start Settings Control Panel. 3.
Page 22
ES1000-Ethernet-ug-en.book Seite 21 Freitag, 19. Januar 2001 5:12 17 6. Bindings: WINS client is not needed for commu- nication with the ES1000. 7. Check the settings for the new network adapter, → especially for address conflicts (Start Set- → tings Control Panel).
ES1000-Ethernet-ug-en.book Seite 22 Freitag, 19. Januar 2001 5:12 17 Configuring the Network Protocol To configure the TCP/IP protocol follow these steps: → → 1. Choose Start Settings Control Panel to open the Network properties dialog box. 2. Double-click the Network icon. 3.
Page 24
ES1000-Ethernet-ug-en.book Seite 23 Freitag, 19. Januar 2001 5:12 17 – IP address: Installation and Configuration with NT 4.0 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 25
ES1000-Ethernet-ug-en.book Seite 24 Freitag, 19. Januar 2001 5:12 17 – DNS: use the settings of your LAN (if no LAN connection is present, no entries are required here). Installation and Configuration with NT 4.0 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 26
ES1000-Ethernet-ug-en.book Seite 25 Freitag, 19. Januar 2001 5:12 17 – WINS: no entries are required here for com- munication with the ES1000 (WINS can be disabled). Installation and Configuration with NT 4.0 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 27
ES1000-Ethernet-ug-en.book Seite 26 Freitag, 19. Januar 2001 5:12 17 – Routing: IP forwarding must not be enabled! If a second network adapter card for the LAN has to be configured, proceed as described above. Ask your administrator for the correct settings. If you have already removed an adapter card for the LAN, enter the old settings.
ES1000-Ethernet-ug-en.book Seite 27 Freitag, 19. Januar 2001 5:12 17 Testing the Installation To check whether the installation of the network adapters and the configura- tion of the network protocol has been successful, follow these steps: → → 1. Open a DOS window (Start Programs Command Prompt) 2.
Page 29
ES1000-Ethernet-ug-en.book Seite 28 Freitag, 19. Januar 2001 5:12 17 Pinging 192.168.40.10 with 32 bytes of data: Reply from 192.168.40.10: bytes=32 time<10ms TTL=128 Reply from 192.168.40.10: bytes=32 time<10ms TTL=128 Reply from 192.168.40.10: bytes=32 time<10ms TTL=128 Reply from 192.168.40.10: bytes=32 time<10ms TTL=128 If time-out messages are generated, check the installation again or possibly restart your PC.
ES1000-Ethernet-ug-en.book Seite 29 Freitag, 19. Januar 2001 5:12 17 Appendix Tested Configurations BIOS Version Operating System 1st Network Card for 2nd Network Card for PCMCIA Mode ES1000 (Driver Version) Company Network (Driver Version) Toshiba TECRA NT4.0 (Service Pack 4) XIRCOM RealPort2 Card- XIRCOM RealPort2 Card- 750DVD CardBus/16-bit...
Page 31
ES1000-Ethernet-ug-en.book Seite 30 Freitag, 19. Januar 2001 5:12 17 BIOS Version Operating System 1st Network Card for 2nd Network Card for PCMCIA Mode ES1000 (Driver Version) Company Network (Driver Version) Toshiba TECRA NT4.0 (Service Pack 4) XIRCOM CardBus Ether- 3Com Megahertz 10/100 780DVD CardWizard-Plus V5.0 net II 10/100...
Page 32
ES1000-Ethernet-ug-en.book Seite 31 Freitag, 19. Januar 2001 5:12 17 BIOS Version Operating System 1st Network Card for 2nd Network Card for PCMCIA Mode ES1000 (Driver Version) Company Network (Driver Version) Toshiba TECRA NT4.0 (Service Pack 4) XIRCOM CardBus 3Com Megahertz 10/100 8000DVD Auto CardWizard-Plus V5.0...
Page 33
ES1000-Ethernet-ug-en.book Seite 32 Freitag, 19. Januar 2001 5:12 17 The CardWizard for NT 4.0 is on the CD-ROM supplied with your Toshiba notebook in the directory driveletter:\COMMON\CWNT\German\SETUP.EXE. No PCMCIA cards should be present in the slots when installing the CardWizard. During installation, the notebook may not be connected to a desk station or to a port replicator.
ES1000-Ethernet-ug-en.book Seite 33 Freitag, 19. Januar 2001 5:12 17 Configuration Parameters for TCP/IP Parameter Setting IP Address PC 192.168.40.240 IP Address ES1120 192.168.40.10 IP Address ES1130 192.168.40.11 Subnet Mask 255.255.255.0 DHCP IP Forwarding WINS Client No (or same as company network) No (or same as company network) Resources for XIRCOM RealPort2 Address...
Page 35
ES1000-Ethernet-ug-en.book Seite 34 Freitag, 19. Januar 2001 5:12 17 Appendix Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
Page 36
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
Need help?
Do you have a question about the ES 1000 Series and is the answer not in the manual?
Questions and answers