Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for QTech WP2P Digital & Analogue
Summary of Contents for QTech WP2P Digital & Analogue
- Page 1 WP2P Digital & Analogue User Guide WP2P Digital & Analogue Version 1.3...
-
Page 2: Table Of Contents
Operational notes – How do the modules communicate? ................. 11 STAT Indicator ............................11 LINK Status Indicator ..........................11 MODE Pushbutton Switch ......................... 12 Technical Specifications ....................13 Warranty ........................14 Additional Information and Support ................14 WP2P Digital & Analogue– User Guide © 2019 QTech Data System Ltd. - Page 3 The information in this document is subject to change without notice and does not represent a commitment on any part of QTech Data Systems Limited. While the information contained herein is assumed to be accurate, QTech Data Systems Limited assumes no responsibility for any errors or omissions.
-
Page 4: About This User Guide
About This User Guide This document provides assistance with the installation and operation of the QTech WP2P Digital & Analogue system. Included in this document is: • How to install the WP2P Digital & Analogue modules • WP2P repeater operation •... -
Page 5: Features
Supports use of a single repeater for difficult terrain or range extension • USB interface for diagnostics and firmware upgrades • Solar power charging and battery operation (when supplied with QTech RSS01 Remote Solar Station enclosure) • Firmware is field upgradeable... -
Page 6: Output Relays
It can be used with both WP2P Digital and WP2P Digital & Analogue type modules simultaneously. Please refer to the WP2P Repeater User Manual for further details. WP2P Digital & Analogue– User Guide © 2019 QTech Data System Ltd. -
Page 7: Preparing For Installation
Consider the use of a QTech WP2P Repeater if the terrain does not permit clear line of sight. Ensure the device is operating the latest firmware especially if the device has been in storage for some time. -
Page 8: Input And Output Wiring
The analogue input jumpers consist of a two- pin jumper header and a three-pin jumper header designated on the board as AIN. The analogue output jumpers consist of two three-pin jumper headers designated on the board as AOUT. WP2P Digital & Analogue– User Guide © 2019 QTech Data System Ltd. -
Page 9: Power Supply Notes
SMPS can impose an AC voltage on the DC ground, which can lead to damage. Suitable cost-effective plug packs are available from QTech P/N PD5412, PD5413 & PD5414. Internal Fuse The device is protected by a 20mm x 5mm 500mA fast blow fuse. This is located on the internal circuit board. -
Page 10: Using Multiple Wp2P Systems In The Same Area
“Channel #1”. Warning – Do not use the same channel for adjacent systems. For example, if you currently use “#1” ensure the adjacent system is “#3” etc. WP2P Digital & Analogue– User Guide © 2019 QTech Data System Ltd. -
Page 11: Operation
SLOW FLASH – Module functioning but no communication with its partner module. • ON – Healthy wireless communications. The LED will briefly flicker each time it receives messages from the other WP2P module. WP2P Digital & Analogue– User Guide © 2019 QTech Data System Ltd. -
Page 12: Mode Pushbutton Switch
Pressing the mode switch briefly will clear the error condition indication on the STAT led. If the fault is still present then the STAT LED will redisplay the error condition. WP2P Digital & Analogue– User Guide © 2019 QTech Data System Ltd. -
Page 13: Technical Specifications
1 x Analogue input, 0-10V or 4-20 mA jumper configurable, (ADC 12 bit +/- 1% FSD) 1 x Analogue output, 0-10V or 4-20 mA, jumper configurable Input voltage: 12V (13.8V max) Current: 100mA average. Internal 500mA fast blow fuse WP2P Digital & Analogue– User Guide © 2019 QTech Data System Ltd. -
Page 14: Warranty
QTech Data Systems Limited does not warrant the suitability of this product for any particular application as the conditions in which it is used are beyond our control. This is not withstanding warranty of merchantability. Additional Information and Support If you have problems try the following: •...