Summary of Contents for PSG Checkmate Xplorer Industrial Harness
- Page 1 Xplorer Industrial Harness Part #s: 47020 | 47021 | 47022 Do not throw away these instructions! Read and understand these instructions before using equipment! Instruction Manual...
-
Page 2: Table Of Contents
ANSI Z359.11 Annex A Introduction Thank you for purchasing a Checkmate Xplorer Industrial Harness. This manual must be read and understood in its entirety, and used as part of an employee training program as required by OSHA or any applicable state agency. -
Page 3: Applicable Safety Standards
Applicable Safety Standards When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.11-2014, ANSI A10.32-2012 standards for fall protection. Applicable standards and regulations depend on the type of work being done, and also might include state regulations if applicable. -
Page 4: Product Specific Applications
Use of equipment in unintended applications WARNING may result in serious injury or death. Maximum 1 attachment per connection point. Product Specific Applications PERSONAL FALL ARREST: The Xplorer Industrial Harness may be used to support a MAXIMUM 1 Personal Fall Arrest System (PFAS) for use in Fall Arrest applications. -
Page 5: Limitations
Limitations FALL CLEARANCE: There must be sufficient clearance below the anchorage connector to arrest a fall before the user strikes the ground or an obstruction. When calculating fall clearance, account for a MINIMUM 2’ safety factor, deceleration distance, user height, length of lanyard/SRL, harness stretch, and all other applicable factors. - Page 6 Limitations COMPATIBILITY: When making connections with the Xplorer Industrial Harness, eliminate all possibility of roll-out. Roll-out occurs when interference between a hook and the attachment point causes the hook gate to unintentionally open and release. All connections must be selected and deemed compatible with the Xplorer Industrial Harness by a Competent Person.
-
Page 7: Components And Specifications
Components and Specifications Adjustable Dorsal D-Ring Rear attachment point Personal SRL Connector Integrated into rear dorsal D-ring Curved Webbing Follows the contours of the body Frontal Attachment Alloy ring for multiple attachments Work Positioning Rings Alloy rings act as work positioning points which pivot to allow the harness to retain form as the user moves Leg Pads... - Page 8 Donning 1. Disconnect the front buckle and leg loop buckles leg. Hold harness up by the rear “D” and check webbing is not twisted. 2. Don the upper part of the harness as you would a jacket. Checking there are no twists in the webbing. Thread the female front buckle through the centre attachment ring, then fold back on itself and connect back to the male half of the buckle, check again for any twists or red stitching..
-
Page 9: Maintenance, Cleaning, And Storage
Maintenance, Cleaning, and Storage If a fails inspection in any way, immediately remove it from service, Xplorer Industrial Harness and contact Guardian to inquire about its return or repair. Cleaning after use is important for maintaining the safety and longevity of the Xplorer . -
Page 10: Labels
Labels ANSI Z359.11–2014 ANSI Z359 recognizes the use of this harness only within the capacity range of: 130–310 lbs. XPLORER INDUSTRIAL HARNESS Compliant with: Cumplir con: Conforme aux normes de: OSHA 1910 OSHA 1910 OSHA 1910 OSHA 1926 Subpart M OSHA 1926 Subparte M OSHA 1926 Sous-partie M Assembled in USA... - Page 11 Inspection Log Serial No: Date: Model #: User: Date: Condition of System: Inspected by: Approved service company: Checkmate Lifting & Safety Ltd. T/A Pure Safety Group, New Road, Sheerness, Kent, ME12 1PZ, UK Tel: 800.466.6385 customer.service@puresafetygroup.com checkmateuk.com...
-
Page 12: Safety Information
Safety Information Failure to understand and comply with safety WARNING regulations may result in serious injury or death. Regulations included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person’s judgment or knowledge of federal or state standards. Do not alter equipment. -
Page 13: Ansi Z359.11 Annex A
ANSI Z359.11 Annex A Note: This information from the Z359.11 standard is required to be included in the instruction manual for the end user. ANSI/ASSE Z359 Requirements for Proper Use and Maintenance of Full Body Harnesses (Note: These are general requirements and information provided by ANSI/ASSE Z359, the Manufacturer of this equipment may impose more stringent restrictions on the use of the products they manufacture, see the Manufacturer’s instructions.) 1. - Page 14 ANSI Z359.11 Annex A (continued) 12. Frontal - The frontal attachment serves as a ladder climbing connection USER INSPECTION, MAINTENANCE AND STORAGE OF EQUIPMENT for guided type fall arresters where there is no chance to fall in a direction Users of personal fall arrest systems shall, at a minimum, comply with other than feet first, or may be used for work positioning.
- Page 15 checkmateuk.com...
- Page 16 Xplorer Industrial Harness Tel: 800.466.6385 customer.service@puresafetygroup.com checkmateuk.com 85401 (Rev B) 2020 © Pure Safety Group...