Advertisement
not over tightened. A screw driver should not be used to hold the
bolt head. Holding a finger on the head of the bolt should be suffi-
cient, when turning the knob. A dime, paper clip or other simple tool
can be used if necessasry.
2.
Set B
s
ase
upporT
"E" adjacent to the Post hole. This will allow pivoting of the p
"d"/B
"e" as required.
ar
3.
Place a p
"d" in each of the B
osT
holes in the post facing forward. This should be a secure fit.
4.
Place the (2) T
ward and secure with the (2) l
so the distance between the pins is approximately the same as the distance between the posts. The k
s
"I" should be 3"-4"apart, centered within the neck area
eTs
5.
Place the assembled T
p
"d", setting the Pins in the B
osTs
lowing the Posts to pivot on these pins.
Loosen the k
s
noB
eTs
of the sweater.
6.
Prepare each a
side of this beam. Hole is determined by Arm Length which is measured from front hole in this beam. Now
place each a
B
rm
eam
Place p
into the appropriate hole in p
in
7.
Insert a
a
rm
djusTmenT
the p
and then the
in
nuT
only to keep the pin from falling free of the a
8.
Push the a
djusTmenT
B
. Push the a
eam
rm
securing the selected position. T o release, simply raise the lower end of the w
Push the outer end of the a
automatically lock the beam in this position. Note: to release, simply raise the lower end of the w
9.
For high neck sweaters, place the (2) n
s
"I" and setting the thin tongue of these B
eTs
in these pieces is on the outer edge. Place the H
Hole in the n
B
eCk
ar
10.
When sweater is dry, remove the a
out through the sleeve. Lift the T
the sweater.
Note: T o move or carry assembled w
"F" over the end of either of the B
ase
B
"A" together, steel pins facing down-
op
eams
s
ong
Crew
B
through both arms of the sweater. Lower this assembly over the
op
eam
"A" into the top holes of the p
eams
"I" and adjust the top and bottom p
B
"B" by inserting the steel C
rm
eam
"B", in turn, through a sleeve, the C
osT
p
"J" through end hole at outer end of B
in
, placing the
nuT
p
"j" up so the end of the p
in
B
down, adjusting it to the desired cuff size. Let the large w
eam
B
down to accommodate the cuff of the sweater. The w
rm
eam
"g". Spread the Neck Bars as required.
B
op
eam
ooly
LACIS,
ase
B
"E" holes with the
eam
k
s
"I" placed through the slots. Spread these bars apart
noB
eTs
osT
onneCTing
onneCTing
"D" to accommodate the sleeve.
approximately ½" from the end of this p
B
. This assembly need not be removed once in place.
rm
eam
falls within the notch in the bottom of the T
in
B
"g" on the T
eCk
ars
between the overlapping T
ars
p
"H" through the slot in the T
olding
ins
B
"B" by removing the pin end from the p
rm
eams
"a", with sweater, off the Posts, and draw the T
B
, pick it up by the 2 p
oard
B
, Ca 94703
erkeley
G
B
ars
osT
I
d
"d". This is a very loose fit, al-
osTs
spacing as desired for the width and shape
p
"C" into one of the 4 holes in the
in
p
"C" facing toward the p
in
. Place the large w
eam
. Note: This nut serves
in
asHer
B
"a" by loosening the k
op
eams
B
op
eams
below the a
osTs
A
H
'2'
eTail
noB
osT
on
asHer
op
drop down,
asHer
.
will
asHer
.
asHer
noB
so the holding hole
B
and the
op
eam
and pull
osTs
B
out of
op
eam
B
.
rm
eams
0704
.
Advertisement
