Subscribe to Our Youtube Channel
Related Manuals for WMT CK6132
Summary of Contents for WMT CK6132
- Page 1 OPERATION MANUAL CNC LATHE MODEL CK6132 Max. swing over bed： Ф320mm Max. length of work piece： 500/750/1000mm Serial number: BE SUBJECT TO ALTERATION WITHOUT NOTICE...
-
Page 2: Table Of Contents
TABLE OF CONTENTS GENERAL SAFETY RULES FOR POWER TOOLS ………………………….…………………….2 SAFETY RULES FOR THE LATHE…………………………………………..………………………..3 INSTRUCTIONS OF OPPEATION ………………………………………………………………..4 A . T H E T E C H A N I C A L P A R T … … … … … … … … … … … … … … … … … … … … … … 4 THE MAIN USAGE AND THE SPHERE OF APPLICATION OF THE LATHE………………………………... -
Page 3: General Safety Rules For Power Tools
GENERAL SAFETY RULES FOR POWER TOOLS WARNING: DO NOT ATTEMPT TO OPERATE UNTIL YOU HAVE READ THROUGHLY AND UNDERSTAND COMPLETELY ALL INSTRUCTIONS, RULES, ETC., CONTAINED IN THIS MANUAL. FAILURE TO COMPLY CAN RESULT IN ACCIDEENTS INVOLVING FIRE, ELECTRIC SHOCK, OR SERIOUS PERSONAL INJURY. MAINTAIN OWNERS MANUAL AND REIEW FREQUENTLY FOR CONTINUING SAFE OPERATION, AND INSTRUCTING THE THIRD-PART USER. - Page 4 9. MAINTAIN TOOLS IN TOP CONDITION Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 10. DISCONNECT TOOLS FROM POWER SOURCE. Before serving and when changing accessories such as blades, bit cutters or when mounting and remounting motor.
-
Page 5: Safety Rules For The Lathe
SAFETY RULES FOR THE LATHE Safety is a combination of operator’s common sense and alertness at all times when lathe is being used. Study these safety rules and general safety rules before operating and retain for further use. 1. wear eye protection. 2. -
Page 6: Instructions Of Oppeation
A. THE TECHANICAL PART 1. THE MAIN USAGE AND THE SPHERE OF APPLICATION OF THE LATHE CK6132 is an economical type of CNC lathe, using two-axis driving system. It is proper for the high efficiency and accurate cutting or processing of metals... -
Page 7: The Figure Of The Lathe
Min. setting unit : 0.01 mm （Z）cross Servo / stepper 0.005 mm （X）long. X/z Rapid speed 7m / min. （Z）cross 4m / min. （X）long. Taper of tailstock quill Max. range of tailstock quill 100mm Motor power (Z) motor (X) motor Packing size (mm) 1815/2120/2300X950X1680mm Net weight... -
Page 8: The Main Structure
HEAD STOCK TAIL STOCK APRON ELECTRIC TOOL POST COOLANT SYSTEM 5. THE MAIN STRUCTURE LATHE BED The lathe bed has been cast into firm cross form by the iron material numbered HT200 with little vibration. Two 90 degree V-type level guide rails are hardened by hyper acoustic quenching and well grinded. -
Page 9: The Transmission System
TAIL STOCK The tail stock can be fastened on the lathe bed by tightening the locking block through one locking handle, there is a sleeve in the tail stock, the taper of it is MT3, there is another locking handle which can tight the sleeve at any position, when you rotate the hand wheel of the tailstock, the sleeve can be moving. - Page 10 TRIAL RUNNING To ensure the long life the characteristic of the bearings, you are suggested to avoid from running at high speed during the beginning period, please alternatively use the speed for the trial running: 460 rounds /min running for 3 hours 750 rounds /min running for 2 hours 1250 round/min...
-
Page 11: The Lubrication System
Number Name Model Quantity Taper ball bearing 7215AC/DB/P5 Taper ball bearing 7014AC/DB/P5 Angular contact ball 7203AC/P5/DB bearing Angular contact ball 7006AC/P5/DB bearing Thrust ball bearing 8102 7. THE LUBRICATION SYSTEM The lubrication of the spindle and the ball bearings are safety-guarded by the hyperthermia grease lubricant. -
Page 12: The Installation
9. THE INSTALLATION When you set the machine tool on the ground, you’ll use the supplied six shockproof sizing block to adjust the level, it is in the perfect condition that the installation precise of the two-way leveling will not exceed 0.04mm/1000... -
Page 13: The Adjustment
FIGGURE5：INSTALLATION 10.THE ADJUSTMENT Before operating on the lathe, in order to ensure the operation precise of the machine tool, the linearity and the levelness of the track must be adjusted To adjust the transmission belt, you’ll adopt the way of moving the motor brackets up and down to realize. -
Page 14: The Maintenance
the locking degree of the clamping lever can be adjusted. THE ADJUSTMENT OF THE CROSS SLIDE The abrasion of the cross slide will be compensated by adjusting the strip inside the slide. Firstly loosen the screw on the big end of the strip, then fasten the screw on the small end of the strip. -
Page 15: The Electrical Part
Forbidden to use the air compressor to clean the machine. B. THE ELECTRICAL PART 1. GENERAL SPECIFICATIONS General power: 380 VAC + 10% -- 15% 50Hz 3-phases Spindle motor: 380 VAC 50 Hz 2.2 KW Motor of coolant system: 380 VAC 50Hz ... - Page 16 To check whether the insulation is good or not, whether the cables or line conductor with breakage, and whether it will do harm to person. To check whether all the electric components in good condition or not. 4. THE STRUCTURES OF SOFT WARE AND HARD WARE OF THE CNC CONTROLLING SYSTEM ( refer to the manual for the debugging and programming of the CNC controlling system)
Need help?
Do you have a question about the CK6132 and is the answer not in the manual?
Questions and answers