Table of Contents
Advertisement
Quick Links
DJD09
DJD10
Keep this instruction sheet for future reference,
as it contains important information.
Requires three AA (LR6) alkaline batteries (not included) for operation.
Adult assembly is required.
Tool required: Phillips screwdriver (not included).
Wipe this toy with a clean, damp cloth. Do not immerse.
This toy has no consumer serviceable parts. Do not take apart.
Actual product may appear different from the photos shown.
fisher-price.com
Advertisement
Table of Contents
Related Manuals for Fisher-Price DJD09
Summary of Contents for Fisher-Price DJD09
- Page 1 DJD09 DJD10 Keep this instruction sheet for future reference, as it contains important information. Requires three AA (LR6) alkaline batteries (not included) for operation. Adult assembly is required. Tool required: Phillips screwdriver (not included). Wipe this toy with a clean, damp cloth. Do not immerse.
-
Page 2: Consumer Information
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052. interference in a residential installation. Hearing-impaired consumers: 1-800-382-7470. This equipment generates uses and can... - Page 3 Assembled Parts 2 Rear Fenders Rear Wheel Base Windshield Dash Side Panel Trunk (outside) Side Base Side Panel Seat Back (inside) Door Part not shown: Label Sheet Front End CAUTION #8 x ¾" (1,9 cm) Screw – 21 SHOWN ACTUAL SIZE This package contains small Tighten all screws with a Phillips parts.
- Page 4 Assembly Rear Fenders Rear Wheel Base Fit the rear fenders onto the rear wheel base. Push to “snap” each rear fender in place. • Hint: Each rear fender is designed to fit one way. If it does not seem to fit, try the other rear fender.
- Page 5 Assembly Seat Back Fit the tabs on the seat back into the slots in the trunk. • Insert two screws into the seat back and tighten. • Side Panel (outside) Front End Rear End Side Panel (inside) Fit the side panels onto the front and rear ends. •...
-
Page 6: Bottom View
Insert nine screws into the side panel and tighten. • Side Base BOTTOM VIEW Carefully turn the car assembly over. • Fit the side base to the front and rear end of the car assembly. • ©2015 Mattel. All Rights Reserved. DJD09-0970 PRINTED IN MEXICO 1100695189-DOM... - Page 7 Assembly Insert six screws into the side base and tighten. • Door Peg Turn the car assembly upright. • Fit the peg on the door into the hole in the car. Push to “snap” in place. •...
- Page 8 Assembly IMPORTANT! Apply labels 7 and 8 to windshield before completing the next step. Apply labels exactly as shown in the illustration. Avoid repositioning a label after it has • been applied. Windshield Dash Fit the windshield onto the dash and push to “snap” in place. •...
-
Page 9: Front View
Assembly BOTTOM VIEW Carefully turn the car assembly over. • Insert four screws into front end and tighten. • Decoration Apply labels exactly as shown in illustrations. Avoid repositioning a label after it has been applied. FRONT VIEW... -
Page 10: Left Side View
Decoration LEFT SIDE VIEW RIGHT SIDE VIEW... -
Page 11: Battery Installation
Battery Installation 1,5V x 3 AA (LR6) For longer life, use alkaline batteries. • Locate the battery compartment on the dashboard. Loosen the screw in the battery • compartment door and remove the door. Insert three AA (LR6) alkaline batteries. •... - Page 12 3 modes of play with fun sounds and lights! Pull the shifter up and down Turn the key Turn the Drop balls in windshield wiper the ramp Press the radio button Open and close the door Turn the steering wheel Press the horn Slide the power/volume switch to ON with low volume , ON with high volume...