Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for enervent eWind
Summary of Contents for enervent eWind
- Page 1 25.01.2016 Enervent eWind User instructions...
-
Page 2: Approvals And Version History
Copyright © Ensto Enervent 2016. Unauthorized copying and lending are prohibited. Approvals and version history Revision Date Description of change Approved by 2016-01-25... -
Page 3: Table Of Contents
Measurements list ........ -
Page 4: Read Me First
READ ME FIRST OPERATION This manual is intended for the user of Enervent Well-functioning ventilation creates the foundation for ventilation unit and eWind control panel. comfortable living. Mechanical ventilation means that fresh outside air is distributed into the building, and used air is blown out. -
Page 5: Using Ventilation Unit
USING VENTILATION UNIT When the ventilation has been carefully planned and installed, there is really not much you need to do. Just sit back, relax and enjoy properly ventilated air. eWind control panel eWind control panel Mode display Temperature display... -
Page 6: Every Day Use Of Ventilation
Every day use of ventilation To select: Press the Mode button to scroll to mode 2. Ventilation is controlled with a simple and easy-to-use • The ventilation system adjusts itself to the control panel that is based on actual use situations. new setting. -
Page 7: Overpressure (Fireplace) Mode
Eco mode Overpressure (fireplace) mode Selecting Eco mode for your ventilation system means If you are going to light the fireplace, you may need to that you allow the system to make slight changes to use the overpressure function. the defined temperature and ventilation values to save energy. -
Page 8: Using Ventilation In Cold Season
Information view closed on a hot day to keep the sun out, or dressing up more warmly on a cold day saves a You can view the active functions from eWind Info list lot of energy. shown in the information display. -
Page 9: Measurements View
To select: You can follow the temperature, humidity, heat recovery efficiency among other measurements in the Press the Eco and Temperature buttons eWind Measurements list shown in the measurements simultaneously twice. display. • A parameter (r1..rn) and the value of the parameter are shown in the display. -
Page 10: Settings View
Settings view Ventilation is not sufficient The Settings menu is for professional use only. It shows If the ventilation is not sufficient: the settings chosen for your ventilation system and Make sure the filters are clean and do not need to allows changing of settings. -
Page 11: Ventilation Is Not Running
Clearing alarms humidity in the air and the ventilation system is trying to get rid of it. If the indoor air is too humid: CAUTION CAUTION: Make sure the filters are clean and do not need to Do not reset the alarm until you have resolved the problem causing the alarm. -
Page 12: Maintenance
CAUTION: Vacuuming/cleaning of the M5 plain and F7 bag filters is not allowed. Acknowledge the FILS service reminder after maintenance by pressing any button on the eWind operating panel for 5 seconds. Pleated filters may be cleaned with compressed air,... -
Page 13: Replacing Filters
Replacing filters Plain filter To replace: DANGER DANGER: Before opening the service hatch, always make sure that the unit’s supply voltage is switched off. NOTE: For LTR-series units: The power cuts off when the service hatch is opened. Open the service hatch. Remove the filter from the ventilation device. -
Page 14: Fans
There is one spare belt attached to all heat Heat exchanger exchangers. NOTE: Visit the HelpCenter on our webpage Inspecting www.enervent.fi for videos showing the maintenance tasks. To inspect: Check the cleanness of the heat exchanger visually To replace: when changing the filters. - Page 15 Detach the bayonet connector from the socket. Unscrew the hexagonal screw of the axle in the middle of the U-beam and remove the beam. Remove the heat exchanger from the unit carefully. 10. Slide the new belt inside around the heat Unscrew the six screws on the heat exchanger exchanger through the opening in the casing and maintenance hatch lid at the front side of the heat...
-
Page 16: Support
A sensor is short- or open Check the connections circuited. malfunction. and wiring of sensors. - - - - Downloading. eWind panel is Normal at start-up. downloading data from ESC Otherwise check the main board. eWind connection cable. Ventilation unit is oFFE Stop mode. - Page 17 Alarm Alarm Description Symptoms Possible reason Action Notes limit Supply fan No Supply air. Supply air fan has stopped. Repair or change the The unit will failure. supply fan. not start before the alarm Extract fan No Extract air. Extract air fan has stopped. Repair or change the condition has failure.
- Page 19 User instructions...
- Page 20 Acknowledge the FILS service To select, press the Mode button for reminder after maintenance by 3 seconds. The display shows first pressing any button on the eWind briefly text on and then F-PL. operating panel for 5 seconds. Ensto Enervent Oy Kipinätie 1...
Need help?
Do you have a question about the eWind and is the answer not in the manual?
Questions and answers