Advertisement
Keep children and unauthorised persons away from the work area.
Avoid unintentional starting.
DO NOT use the polisher for any purpose other than that for which it is designed.
DO NOT operate the polisher if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT switch the polisher on until the head is in contact with the panel and switch the unit off before removing the head from the panel.
DO NOT use the polisher with abrasive cleaners or rubbing compounds as excessive paint removal may result.
DO NOT get the polisher wet or use in damp or wet locations or areas where there is condensation.
DO NOT allow untrained persons to operate the polisher.
DO NOT operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT use the polisher where there are flammable liquids, solids or gases such as paint solvents, etc.
DO NOT leave the polisher operating unattended.
DO NOT carry the polisher with your finger on the power switch.
DO NOT pull the cord from the power supply.
Use a qualified person to maintain the polisher.
When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
2. INTRODUCTION
Random orbital polisher with Ø150mm 3 ply foam pad and two polishing bonnets. Smooth operation provides even buffing/polishing with no
hot spots. Impact resistant ABS housing with twin grips. Supplied with 4mtr cable and BS approved plug. GS/TUV and CE approved.
3. SPECIFICATION
Model no: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ER150P
Input: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V 50Hz
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60W
Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3800rpm
Pad Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150mm
4. OPERATION
WARNING! Ensure that you read, understand and apply the safety instructions in Section 1.
WARNING! Excess pressure can cause damage to paintwork and will put the polisher motor under strain. Polishers returned
with burnt out motors will be rejected as a warranty claim. Normally the weight of the polisher is sufficient.
WARNING! Do not use the polisher with abrasive or rubbing compounds.
4.1.
Before each use, check that the bonnet is clean and free of abrasive particles and is undamaged and that the pad rotates freely.
4.2.
Apply a small amount of polish/wax evenly over the surface of the bonnet. Do not apply polish directly to the vehicle surface.
4.3.
Hold the polisher firmly by the handles and place the polishing face onto the panel to be polished.
4.4.
Start the polisher using the red on/off switch on the handle ensuring that the pad is still in contact with the vehicle panel.
4.5
Move the polisher with broad sweeping strokes over the surface in a criss cross pattern. Do not apply pressure to the polisher when in
use. Work in logical areas and re-apply the polish/wax at intervals during the polish application process. Do not allow the foam pad to
become saturated with polish/wax as this will make polishing more difficult and will reduce pad life.
4.6.
Polish/wax should be applied to difficult-to-reach areas by hand.
4.7.
Switch off the polisher before lifting it from the panel when polish application is completed.
4.8.
Remove the application bonnet and replace it with the wool bonnet.
4.9.
Buff the polish/wax in the same order it was applied. Do not put pressure on the polisher but allow its weight and action to do the job.
4.10
Badly oxidised paint may require several applications. Do not use abrasive compounds.
4.11
If the polish/wax is difficult to buff too much has been applied. This may also cause the bonnet to come off the pad.
WARNING! Do not immerse the polisher in water.
5. MAINTENANCE
5.1
Always store the polisher on its side so that the foam pad does not become compressed and/or distorted.
5.2
Remove the bonnet when not in use to allow the foam pad to dry out.
5.3
Clean the bonnet regularly by hand washing with soap and water. Do noT immerse the foam pad in water. Washing the bonnet is
sufficient.
5.4
If the foam pad requires replacement return the unit to your local Sealey dealer as this is not a user servicable part.
Environmental Protection.
Recycle unwanted materials instead of disposing of
them as waste. All tools, accessories and packaging
should be sorted, taken to a recycle centre and
disposed of in a manner which is compatible with
the environment.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.2m/s²
Cable Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4mtr
Replacement Bonnet Terry Cloth: . . . . . . . . ER150P.TB
Replacement Bonnet Synthetic Wool: . . . . . ER150P.WB
When the product is no longer required, it must be
disposed of in an environmentally protective way.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
Rechargeable battery contains nickel cadmium
(niCad). It is recyclable. Take to your local recycling
centre to be disposed of properly. Do not incinerate
niCad battery as it may explode when exposed to
fire. Do not attempt to open battery pack.
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
ER150P
Issue: 2 - 20/10/09
Advertisement
