Download
Share
Print this page
TOHATSU VE1500A-Ti Owner's Manual
  1. Manuals
  2. Brands
  3. TOHATSU Manuals
  4. Control Panel
  5. VE1500A-Ti
  6. Owner's manual
TOHATSU VE1500A-Ti Owner's Manual

TOHATSU VE1500A-Ti Owner's Manual

Remote panel
Hide thumbs Also See for VE1500A-Ti:

Advertisement

Quick Links

Download this manual
REMOTE
PAN EL
Original instructions
VE1500A-Ti
OWNER'S
MANUAL
No.003-12086-1

Advertisement

loading

Related Manuals for TOHATSU VE1500A-Ti

Summary of Contents for TOHATSU VE1500A-Ti

  • Page 1 REMOTE PAN EL Original instructions VE1500A-Ti OWNER’S MANUAL No.003-12086-1...
  • Page 2 Copyright © 2020 Tohatsu Corporation. All rights reserved. No part of this manual may be reproduced or transmitted in any from or by any means without the express written permission of Tohatsu Corporation.
  • Page 3 APPLICATIONS OF THIS REMOTE CONTROL PANEL USAGE TOHATSU portable fire pump “VE1500A-Ti” and the remote control panel are intended only for firefighting activities in collaboration with general public fire extinguishing equipment. Using these products for the other applications is regarded as being used for improper purposes.
  • Page 4 Place owner’s manual so that operators can refer to it where they operate the fire pump and the control panel. General safety information Before operating the TOHATSU remote control panel and the fire pump, thoroughly read the manual and understand...
  • Page 5 Before using this fire pump, write down the serial number. It will be useful in the case of asking about servicing, repairs and genuine parts. Serial Number The identification of remote control panel is marked on the back of the control panel.

  • Page 6: Table Of Contents

    CONTENTS OPERATION DEVICE………..…..……..…..…..……..…….……..…1 DESCRIPTION OF DEVICES…………………..……………..…..….…….…2 USE OF REMOTE CONTROL PANEL…………………….….…..…..…5 STARTING THE ENGINE….…..………………..…….………..…..…..9 PRIME AND DISCHARGE……………..………...…...….……..….….…….11 STOPPING THE ENGINE.…………………….…..….…………….…….….13...

  • Page 7: Operation Device

    1. OPERATION DEVICE ① ③ ⑭ ② ⑤ ⑧ ⑨ ⑬ ⑩ ⑮ ⑥ ⑦ ⑫ ④ ⑯ ⑪ Engine running status lamp ① Discharge water status lamp ② Warning lamp: Suction water, Engine oil, MAT/MAP ③ Warning lamp: Battery, Overheat, TPS/WTS ④...

  • Page 8: Description Of Devices

    2. DESCRIPTION OF DEVICES Remote Control Panel The remote control panel should be connected to the pump (VE1500A-Ti) control panel. ① ③ ⑭ ② ⑤ ⑧ ⑨ ⑬ ⑩ ⑮ ④ ⑯ ⑫ ⑪ ⑦ ⑥ Lamp Engine running Turn on：Engine running.
  • Page 9 2. DESCRIPTION OF DEVICES Switch Main switch Power and control panel lamps turn on. ⑥ Start the engine with starter. Start switch, Low pressure throttle ⑦ Turn the throttle to low pressure position while the position switch engine is running. Throttle position Turn the throttle to engine start position and suck up ⑧...
  • Page 10 2. DESCRIPTION OF DEVICES Lamp check (Alert action check) When the warning lamps are off, there is no trouble on each function. If the warning lamp(s) is on or blinking, the pump does not work properly. Turning on the power, the warning lamps and buzzer will be NOTE activated for approximately one second.

  • Page 11: Use Of Remote Control Panel

    3. USE OF REMOTE CONTROL PANEL Operation procedure using remote control panel Connect the remote control panel to the operation panel of pump (VE1500A-Ti). 1) Turning on the power Throttle position switch Turn on the power pressing the main switch.
  • Page 12 If the engine does not start in five time starting operations, eliminate the cause of failure, then start the engine. VE1500A-Ti pump control panel does not have the engine running status lamp and the discharge water status lamp. Discharge water...
  • Page 13 3. USE OF REMOTE CONTROL PANEL Warning system Remedy Warning...
  • Page 14 B: Remove the cause of insufficient cooling water and restart the engine. * C: Remove the cause of insufficient cooling water.* * Refer to VE1500A-Ti owner's manual / TROUBLESHOOTING. D: Charge the battery. E: Remove the cause of unable suction water.

  • Page 15: Starting The Engine

    4. STARTING THE ENGINE Operating VE1500A-Ti is possible with both of the pump control panel and the remote control panel. Connect the remote control panel to the operation panel of pump (VE1500A-Ti). * VE1500A-Ti pump control panel does not have the engine running status lamp and discharge water status lamp.
  • Page 16 4. STARTING THE ENGINE The throttle position turns to the low pressure position after NOTE completed of sucking water at automatic suction water mode just after the power on. When the engine starts, the engine running lamp turns on. When the starter motor runs for a long time continuously, the power of the battery will be exhausted quickly.

  • Page 17: Prime And Discharge

    Low pressure position If the pump could not suck up CAUTION water completed in 30 seconds in Priming failure lamp auto priming mode, warning lamp lights warning buzzer sounds. Eliminate cause referring “Owner’s manual VE1500A-Ti/ TROUBLESHOOTING”.
  • Page 18 5. PRIME AND DISCHARGE Discharging water Check that the nozzle is ready to CAUTION discharge water before opening the discharge valve(s). And inform the operator(s) on the nozzle side that the discharge valve(s) is going to open and confirm that it is OK. 1.

  • Page 19: Stopping The Engine

    6. STOPPING THE ENGINE Decreasing 1. Return the throttle to the low pressure position pressure switch pressing “ ” or “ : Decreasing pressure switch”. Start switch/Low pressure throttle position switch 2. Close the discharge valves. Discharge valve Close 3. Press the stop switch “ ”...
  • Page 20 RE M OTE PA N E L VE1500A-Ti OWNER’ S MANUAL No.003-12086-1 5-4, Azusawa 3-Chome, Itabashi-Ku Tokyo 174-0051, Japan Phone : +81-3-3966-3137...