Advertisement
If battery has caps to access the battery fluid, remove the caps and check the fluid level before connecting the power clamps. If
9
necessary top-up the battery with distilled water by referring to the battery manufacturer's instructions. Apply the personal
safety precautions described in part 1.3.
If the charger receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
9
If the battery terminals are corroded or dirty clean them before attaching the power clamps.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT dis-assemble the charger for any reason. The charger must only be checked by qualified service personnel.
8
DO NOT try to charge a non-rechargeable battery.
8
DO NOT try to start engine when charger is connected to battery.
8
DO NOT try to charge battery if battery fluid is frozen.
8
WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow
‰
them to touch the battery terminals.
DO NOT allow power clamps to touch each other or to make contact with any metallic part of the vehicle.
8
DO NOT cross connect power leads from charger to battery. Ensure positive (+/RED) is to positive and negative (-/BLACK) is to
8
negative.
DO NOT pull the cables or clamps from the battery terminals.
8
DO NOT use the charger outdoors, or in damp, or wet locations and DO NOT operate within the vicinity of flammable liquids or gases.
8
DO NOT use charger inside vehicle or inside engine compartment.
8
Ensure there is effective ventilation to prevent a build-up of explosive gases.
9
DO NOT use the charger for a task for which it is not designed.
8
WARNING! DO NOT simultaneously charge batteries of different capacities or discharge levels.
‰
WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating. Use only Sealey genuine parts.
‰
When not in use, store the charger carefully in a safe, dry, childproof location.
9
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical,
9
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by children without supervision.
2.
INTRODUCTION
Dual voltage smart charger (6V / 12V) and maintainer ensures that the battery is kept fully charged and ready to use for extended
periods of time. Clear, easy-to-read LED status lights indicate the current charging or 'float' mode. Heavy-duty case with simple
controls. Charges conventional lead acid and AGM/GEL batteries. Inbuilt reverse polarity protection.
3.
SPECIFICATION
i
Model no .............................................AUTOCHARGE100HF
Output ...........................................................................6/12V
Output charge ....................................................................1A
Battery range ...........................................................0.8-14Ah
Cable length ................................ 1m (to quick connect plug),
..................................... 1.4m (including clamps/eyelet cable)
Supply ............................................................................230V
IP rating ..........................................................................IP20
4. OPERATION
4.1.
CONNECTING TO THE BATTERY.
NOTE: The charger should be connected to the mains supply before connecting to battery and pre-selection made for
battery voltage prior to connection to battery.
4.1.1.
The output cable from the charger terminates in a polarity conscious socket into which the two alternative leads can be connected.
4.1.2.
One lead set has two colour coded battery clamps which can be quickly attached to and detached from the battery posts. The second
lead is for semi permanent connection to the battery via eyelets.
4.2.
CHARGING A NEGATIVE EARTHED BATTERY
4.2.1.
Ensure that the black clamp on the clamp lead is not touching the battery or the fuel line.
4.2.2.
Connect the positive (+) red clamp to the positive (+) battery post and connect the negative (-) black clamp to the negative (-) battery
post or vehicle chassis.
4.3.
CHARGING A POSITIVE EARTHED BATTERY
4.3.1.
Ensure that the red clamp on the clamp lead is not touching the battery or the fuel line.
4.3.2.
Connect the negative (-) black clamp to the negative (-) battery post and connect the positive (+) red clamp to the positive (+) battery
post or vehicle chassis.
4.4.
BATTERY NOT CONNECTED TO A VEHICLE
4.4.1.
Connect the (+) red clamp to the positive (+) battery post and connect the (-) black clamp to the negative (-) battery post.
© Jack Sealey Limited
Original Language Version
AUTOCHARGE100HF
Issue 3 (3)
13/03/20
Advertisement
