Related Manuals for Panduit NET-SERV Series
Summary of Contents for Panduit NET-SERV Series
- Page 1 Cabinets INSTRUCTIONS CM408F © Panduit Corp. 2009-2011 FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp Page 1 of 24...
-
Page 2: Cabinet Operation
Casters can support a fully loaded cabinet. However, the casters should only be used to move the cabinet from one location to another. To ensure maximum stability, the leveling legs should be used to support the cabinet when it is in the permanent location. Not all features are included with all Net-SERV configurations. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 2 of 24... -
Page 3: Accessory Guide
POU Brackets (SCSTR) (SVPDUB) [6] L-Fingers and [1] CMSRC2 are included per panel Cable Management Panel and L-Retainers Cable Management Finger Bracket and Fingers (S62BRFK, S65BRFK, S72BRFK, S75BRFK) (S62BRCK, S65BRCK, S72BRCK, S75BRCK) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 3 of 24... - Page 4 The maximum weight load of the cabinet is 2500 pounds (1134 kg). The weight load should be evenly distributed across the height of the cabinet, with the heaviest components mounted at the bottom of the cabinet. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 4 of 24...
- Page 5 (2) #10-32 trilobular screws per bracket in the locations shown. Top Ganging Location Ganging Bracket #10-32 Trilobular Screw Ganging Bracket #10-32 Trilobular Screw 600mm/700mm Spacing 24” Spacing Bottom Ganging Location For Technical Support: www.panduit.com/resources/install_maintain.asp Page 5 of 24...
- Page 6 27.6" [700mm] 47.2" [1200mm] 40.7" [1035mm] 11.8" [300mm] 45.2" [1148mm] 10.5” [267mm] 23.6" [600mm] 39.3" [1000mm] 23.6" [600mm] 39.3" [1000mm] 33.6" [853mm] 9.8" [250mm] 37.3" [947mm] 27.6" [700mm] 39.3" [1000mm] 27.6" [700mm] 39.3" [1000mm] 33.6" [853mm] 11.8" [300mm] 37.3" [947mm] For Technical Support: www.panduit.com/resources/install_maintain.asp Page 6 of 24...
- Page 7 N configurations that ship with split doors installed on cabinet. Grounding Lug Locations Remove masking and attach grounding lug with 2) #12-24 screws Grounding Lug Location Detail For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 24...
-
Page 8: Equipment Rail Adjustment
(use 1/2” socket) Top Location Equipment Rail Bracket Equipment Rail Bracket Loosen (2) 5/16” Bolts to release clamping Bottom Location pressure for front to back rail adjustment (use 1/2” socket) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 8 of 24... - Page 9 (2-top, 2 bottom) for large cable management bracket adjustments (use 5/16” socket) Loosen (2) #12-24 Hex Head Screws for precise Cable Management Cable Management bracket adjustment Finger Bracket Finger (use 5/16” socket) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 9 of 24...
- Page 10 (2) #12-24 Phillips Locations Screws (6 Places) Cable Management L-Retainer (installed) Cable Management Panel Keyed Mounting Slot Release Tab Loosen (2) #12-24 Hex Head Screws for precise bracket adjustment (use 5/16” socket) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 10 of 24...
- Page 11 Bottom Blanking Panel #10 Phillips Screws and #10 lockwashers (Remove and use to install bottom blanking panel) To Adjust: Loosen (12) #10 Phillips Screws on each vertical blanking panel [6] screws per side For Technical Support: www.panduit.com/resources/install_maintain.asp Page 11 of 24...
- Page 12 Note: Make sure that both pins are fully engaged when door is installed. Upper Door Mounting Bracket Upper Hinge Pin (pull lever down) Lower Hinge Pin Lower Door Mounting Bracket For Technical Support: www.panduit.com/resources/install_maintain.asp Page 12 of 24...
- Page 13 180º. Rotate orienation of cam stop 90º clockwise while door handle cam and hex bolt are removed from handle assembly. Reinstall handle assembly into Single Hinge Door. See ‘Door Handle Direction Reversal’ view below. Remove PANDUIT label from bottom of door and reinstall label centered and 7-1/4”...
- Page 14 Open each split door to 90 and slide door away from cabinet and out of hinges. Reverse steps to reinstall split doors. Disconnect (2) Grounding Jumpers Remove (4) hinge pins from split doors With split door open to 90 slide door out of hinges For Technical Support: www.panduit.com/resources/install_maintain.asp Page 14 of 24...
-
Page 15: Side Panel Installation
(2) latches engage. Pull down on the (2) latches to disengage the side panel, then rotate and lift the panel to remove. Install grounding clips as necessary Pull down and release latches Side Panel Bottom Side Mounting Hook Panel Support For Technical Support: www.panduit.com/resources/install_maintain.asp Page 15 of 24... - Page 16 (use 5/16” socket) POU Mounting Bracket Loosen (2) #12-24 Hex Head Screws for precise bracket adjustment (use 5/16” socket) Loosen (2) #12-24 Hex Head Screws for precise bracket adjustment (use 5/16” socket) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 16 of 24...
- Page 17 INSTRUCTIONS CM408F POU Mounting Bracket Locations 1 RU [1.75] For Technical Support: www.panduit.com/resources/install_maintain.asp Page 17 of 24...
- Page 18 NOTES -SVPPB to be used with finger bracket only (700mm/28”) -Recommend use with Panduit Pan-Net and Quick-Net (1) Rack Unit Patch Panels -(3) SVPPB may be fitted to a 42 RU (700mm/28”) cabinet -(4) SVPPB may be fitted to a 45 RU (700mm/28”) cabinet...
- Page 19 Bezels can be removed from cabinet top by depressing tabs and pulling out of position. The remaining knock- outs can be removed by cutting the (8) tabs with a wire cutter as shown. Additional bezels and bezel inserts are available for purchase. Removable Bezel Inserts Overhead Cable Opening Bezel For Technical Support: www.panduit.com/resources/install_maintain.asp Page 19 of 24...
- Page 20 (2) #10 nuts per bracket using a 3/8” socket wrench or end wrench. Extend the end seal bracket and retighten (2) #10 nuts. End Seal Bracket Loosen and retighten #10 nuts to adjust end seal bracket Use 3/8” socket wench or 3/8” end wrench UNDERSIDE VIEW OF TOP COLLAR For Technical Support: www.panduit.com/resources/install_maintain.asp Page 20 of 24...
- Page 21 Top 3/16” x 1/2” Adhesive Foam Seal Flange in Side (apply behind grounding clip) Panel Opening Grounding Clip 3/16” x 1/2” Adhesive Foam Seal Top Side Panel Seal (only apply when side panel is installed) (Section View) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 21 of 24...
- Page 22 NOTE: SFS-KIT is required for end of row floor sealing. [2] #10-32 x 1/2” Phillips Trilobular Screws and Paint Piercing Washers Floor Seal Bracket [2] #10-32 x 1/2” Phillips Floor Seal Bracket Trilobular Screws and Paint Piercing Washers For Technical Support: www.panduit.com/resources/install_maintain.asp Page 22 of 24...
- Page 23 BLANKING PANEL Right Door Catch Blanking Panel (Adjust upwards so that both door catch openings are blanked) #6 Phillips Screw Rubber Door Bumper (Maneuver blanking panel around bumper when repositioning) Default Blanked Area For Technical Support: www.panduit.com/resources/install_maintain.asp Page 23 of 24...
- Page 24 INSTRUCTIONS CM408F THIS PAGE IS LEFT BLANK INTENTIONALLY For Instructions in Local Languages E-mail: and Technical Support: cs@panduit.com Fax: www.panduit.com/resources/install_maintain.asp (708)444-6448 www.panduit.com Page 24 of 24...