ShoreTel ShoreGear Dual Tray Installation Manual

Introduction and Specifi cations
The ShoreGear Dual Tray Package Contains:
• ShoreGear Dual Tray
• Two center mounting ears
• Two outer mounting ears
• Two M3.5 screws for attaching mounting ears to the Dual Tray outer frame
• Two M3 screws for attaching the mounting ears to the Dual Tray center post
• Eight M3 screws for attaching mounting ears to a ShoreGear voice switch
(screws for attaching mounting ears to switch are also included with the switch)
S horeG ear D ual Tray
C enter P ost
O uter m ounting ear
O uter P osts
C enter m ounting ear
About The ShoreGear Dual Tray
The ShoreGear Dual Tray allows mounting of one or two ShoreGear half-width voice
switches in a single 1U 19-inch rack position or on a wall. The contents of the ShoreGear
Dual Tray package contains the parts required to mount two half-width switches into a
19-inch rack.
Mounting half-width switches on a wall requires the installation of two wall mount
brackets onto the Dual Tray. The ShoreGear Dual Tray Wall Mount Kit provides additional
equipment and instructions required to mount the switches on a wall.
Installation Equipment
To install the switch, you need the following equipment:
• #1 Phillips screwdriver
• Four rack mount screws
Installation Location Requirements
To ensure optimum operating conditions for the switches that will be installed in the
ShoreGear Dual Tray, verify the operating environment is adequately ventilated, free of
gas or airborne particles, and isolated from electrical noise.
Rack Mount Cautions
Temperature: The operating ambient temperature of the closed or multi-unit rack
environment may be greater than room ambient temperature. When installed in a
rack, the ambient temperature of the Dual Tray must remain lower than the maximum
operating ambient rating of the ShoreGear Voice Switches – typically 50° C.
Air Flow: Verify that the Dual Tray has adequate airfl ow when installed in a rack.
Power circuit loading: Use the equipment nameplate rating to calculate the maximum
number of units on each branch circuit. Branch circuit loading is limited to 80% of the
branch rating. For example, if the nameplate rating is 1 Amp, no more than 12 units
can be connected to a 15 Amp branch circuit.
Reliable Grounding: Reliable grounding of rack-mounted equipment must be
maintained. Pay specifi c attention to supply connections other than direct connections
to the branch circuit (e.g. power strips).
Installing the ShoreGear Dual Tray
Installing the ShoreGear Dual Tray in a 19-inch Rack
Position the ShoreGear Dual
1.
Tray at the desired position in
the rack.
2.
Installing Switches into the Dual Tray
Attaching Mounting Ears to a ShoreGear Voice Switch
Remove four M3 screws from the voice
1.
switch.
The screws – two from each side panel
– are located near the front panel of the
switch.
M o u n tin g E a r p la ce m e n t fo r in sta lla tio n
in to le ft sid e o f th e Tra y
Secure the Dual Tray to the rack
using four rack mount screws.
Rack mount screws are not
provided in the ShoreGear Dual
M o u n tin g E a r p la ce m e n t fo r in sta lla tio n
Tray package.
in to rig h t sid e o f th e Tra y
Attach the Mounting Ears to the sides of the voice switch,
3.
using the four screws removed from the switch in Step 1.
Installing a ShoreGear Voice Switch into the Dual Tray
After placing the Dual Tray in the rack and attaching the Mounting Ears to a voice
switch, you can install the Voice Switch into the Dual Tray.
Place the switch in the side of the
1.
tray for which the mounting ears
were attached.
Insert an M3.5 screw through the outer
3.
Mounting Ear and into an outer post of
the Dual Tray.
Insert an M3 screw through the inner
Mounting Ear and into the center post of
the Dual Tray.
Specifi cations
Feature
Dimensions
Weight
Determine the Mounting Ear installation
2.
orientation.
Mounting Ear orientation depends on the side
of the tray where the switch will be placed.
Slide the switch into the tray until it is
2.
captured by the lip at the back of the tray.
M 3
screw
M 3.5
screw
Specifi cation
1.75 x 19.125 x 14.625 inches (44 x 486 x 371 mm)
3.8 lb (1.7 kg)