Quoizel BST8407MB Installation Manual

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A19 Medium Base Bulb 100W Maximum, Medium Base Vintage Bulb is recommended, bulb not included.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact your original place of purchase.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar
A Assembly
x 1
Alternate
B Mounting screw
x 2
Lock screw
C
x 2
-
STEP 1 Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet Box
Mounting Screw
or Alternate Short
Mounting Screw
Figure 1
-
STEP 2 Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (E) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (E) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws in or
2018 QuoizelInc.
for product cleaning tips. Go to the
20-30 minutes
Arm
D
x 1
Fixture Body
E
x 1
F
Supply Wires
with Ground Wire
A
Outlet Box Screws
(not included)
visit us on-line at www.quoizel.com
Installation Guide #IS-BST8407MB
For Style BST8407MB
Care + Maintenance selection.
(Step 2 Continued)
out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (E) is secure, remove the mounting ball
and Fixture Body (E).
Mounting Screw
or Alternate Short
Mounting Screw
Cage with
Glass Shade
x 1
STEP 3 - Install Arm, Bulb and Cage with Glass Shade
A. Remove the lock ball from the top edge of the backplate.
B. Place the scroll end of the Arm (D) into the loop and attach the other
end of the Arm (D) over the bolt on the backplate and secure with
previously removed lock ball. Hand tighten until snug.
C. Insert the bulb onto the socket and screw snugly into place.
D. Place the Cage with Glass Shade (F) over the bulb and socket.
.
Lock Ball
Backplate
Figure 3
1of2
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
D
(Scroll End)
Loop
Bolt
E
Socket
Vintage Bulb
(recommended
but not included)
E
Figure 2
Neck of Socket Cup
C
F
ReleasedDate:2018-09-17