Quoizel LTE8407PN Assembly Instruction Sheet

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) Medium Base 100W bulb Maximum.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
Fixture
x 1
Body
-
STEP 1 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Outlet
Box
Figure 1
STEP 2 - Remove Styrofoam
inside of the Fixture
Body
A. Remove the Shade (C) and
Styrofoam inside the Fixture
Body (B).
Figure 2
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2016 QuoizelInc.
Assembly Instruction Sheet #IS-LTE8407PN
for product cleaning tips. Go to the
20-30 minutes
B
C
x 1
A
Outlet Box Screws
(not included)
Supply Wires
with Ground Wire
B
Styrofoam
C
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style LTE8407PN
Care + Maintenance selection.
-
STEP 3 Fit Backplate to Crossbar Assembly
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate on Fixture Body (B) to the Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate on Fixture Body (B)
should be snug against the wall and the mounting balls. If not,
adjust the length of the mounting screw on the Crossbar Assembly
(A) by unscrewing the
preassembled hex nut and
lock washer and then
screwing the mounting
Shade
screws in or out of the
x 1
crossbar until the correct
length is achieved. Once
the backplate on Fixture
Body (B) is secure, remove
the mounting ball and
Fixture Body (B) and
proceed to Step 4.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
-
STEP 5 Install Fixture Body
A. Carefully tuck all wires into the
outlet box and position the
backplate of Fixture Body (B)
over the outlet box. Align the
holes in the backplate with the
mounting screws. Place caulk
(not supplied) into the
previously removed mounting
balls and then attach Fixture
Body (B) using the mounting
balls. Hand tighten until snug.
1of2
Mounting Ball
Mounting
Screw
A
Hex Nut and
Lock Washer
Backplate
Figure 3
White wire
from fixture
Black wire
from fixture
Figure 4
Ground wire
from fixture
Mounting Ball
Mounting
Screw
A
Hex Nut and
Lock Washer
Backplate
Figure 5
ReleasedDate:2016-11-03
B
B