Keep this User Manual handy for ready reference. Note 1. It is strictly prohibited to use part or this entire manual to other publication without permission of publisher. 2. The contents of this manual and the specification of the product may change without a preliminary notice for future improvement. 3. Please contact a regional distributor of LAUREL, if there are any doubtful points, errors, etc. in this manual. 4. It is understood that LAUREL will not be responsible for any loss caused by use of the product, regardless of any errors in the manual. 5. The illustrations in this manual may differ from the actual product as they are abstract. 6. The display screen illustrated in this manual may differ from an actual display screen. 7. Please contact a regional distributor of LAUREL if the manual has disorderly binding or ...
Operation of this equipment in a residential area is likely to cause harmfulinterference in which case the user will be required to correct the interference at his own expense. FCC Label in The Machine Only for K4 Only for K8 Introduction...
Request from us If you don't use the machine for long, be sure to turn off the power switch. *About the installation of the machine: Avoid high temperature, high humidity, dust, vibration, and direct sunlight. 。 。 In case the environment of operation exceeds room temperature (5 C to 34 C) and humidity (35% to 80%), the performance of the machine will deteriorate remarkably.
Contents Introduction ..................... ii Note ..........................ii FCC Caution ........................ii FCC Note ........................iii FCC Label in The Machine ..................iii Request from us ......................iv Before Operation ..................viii Description of Warning, Caution and Examples ..........viii Description of Symbol and Examples ..............viii Discription of Symbols and Examples ..............viii Safety Caution ..................ix About instantaneous voltage drop ............... xi About Maintenance Service ..................xi Description of This Manual............... xii Chapter 1 OVERALL DESCRIPTIONS Description of Each Part ...
Page 6
Chapter 2 DESCRIPTION OF OPERATION Starting-up and Closing-down of the Unit ........24 Count ....................... 26 Setting of Sorting Modes and Sorting Pattern ......29 Setting of Preset Number..............31 Total Function ..................33 Setting of Fitness Level ..............38 Setting of CF Level ................41 Function Setting .................. 43 Cleaning ....................49 Periodical Cleaning and Position ................49 Cleaning the Dust Tray 1 ..................49 Cleaning the Dust Tray 2 ..................50 Cleaning Sensors .......................52 Chapter 3 ...
Page 7
Chapter 4 INSTALLATION, SPECIFICATIONS AND OTHERS 81 Installation ..................... 82 Condition of installation ...................82 Installation and Transfer ..................82 Specifications ..................83 Accessories ..................84 Contents ...
Before Operation This manual is used to follow symbols to make you cautious in order to use the machine safely and to prevent you from a risk of an injury or from losing your property. It describes contents of danger and/or how to prevent the danger together with marking which indicates contents of the danger near the symbols.
When you transfer the machine, please contact a regional distributor. If you transfer the machine without safety planning, it may cause a break or a RISK OF trouble and there is a risk of an injury due to the machine's declining. INJURY CAUTION Be sure to stop the machine completely when the power switch is turned off. If the power switch is turned off while operation, it may cause failure of machine. When cleaning the machine, please turn off the power switch and remove the plug from outlet. Otherwise, there is a risk of injury due to sudden motion. When the machine is installed, be sure that the base is flat and stable. Without respect to this caution, it may make the machine fall or break and/ or you will get an injury from it. The power cable enclosed in the box is exclusive for the machine. Use the cable for the machine. Otherwise there is a risk of failure, an electric shock or a fire. Hold the specified part when opening and closing doors and be sure not to pinch your finger. Otherwise, there is a risk of an injury. RISK OF INJURY The weight of K4 is about 95kg and K8 is about 130kg. When you move the machine location, be sure to prevent from backache or machine's declining. RISK OF INJURY Safety Caution...
Page 10
CAUTION Do not lean over, sit, step on or place heavy material on the machine. Otherwise, there is a risk of injure due to fall down the machine. RISK OF INJURY When removing the plug, be sure to hold the plug itself. If the plug is removed by holding the cable, it may cause physical failure, an DISMOUNT electric shock or a fire. PLUG Be sure to connect the earth wire to the proper grounding. Otherwise, there is a risk of electric shock. Do not connect earth wire to gas pipe. There is a risk of explosion. RISK OF EXPLOSION Do not touch the machine or power cable with a wet hand. There is a risk of an electric shock. RISK OF ELECTRIC SHOCK Do not place heavy material on the power cable or other interface cable. Also do not twist or pull out the cables. There is a risk of failure, an electric RISK OF shock or fire. ELECTRIC SHOCK Do not use the machine by other than the specified power (AC90 to 252V). There is risk of an electric shock and a fire. RISK OF ELECTRIC SHOCK Do not connect many plugs to one outlet. Adapter connecting outlet may heat up and there is a risk of a fire. RISK OF INJURY Do not install the machine at a moist area, dusty or any place for handling water.
Do not use the power cable which is not for the machine.There is a risk of failure, an electric shock or a fire. About instantaneous voltage drop This machine may have a problem due to instantaneous voltage drop by thunderbolt etc. We recommend employing UPS etc for countermeasure. About Maintenance Service This machine requires proper maintenance service. Please contact a regional distributor of LAUREL for further details about maintenance service. Safety Caution...
Description of This Manual K4/K8 Chapter 2 DESCRIPTION OF OPERATION STEP-3 STEP-3 Align the notes and put the notes It describes operation onto the Hopper. procedure. ▷ The count starts automatically. ▷ I f t h e c o u n t d o e s n o t s t a r t ...
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Description of Each Part Overall Unit Only for K4 2. Status LED 1. Pocket LED 3. Sub-Display 4. Pocket 1 15. Reject Pocket 5. Pocket 2 16. Reject Pocket LED 6. Pocket 3 17. Note Press 7. Pocket 4 18. Note Guide 12. Operation Panel 19. Main SW 13. START/STOP SW 20. Hopper 14. Note Press SW 21. Dust Tray 1 Description of Each Part...
Page 15
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 2. Status LED 1. Pocket LED 3. Sub-Display 8. Pocket 5 9. Pocket 6 15. Reject Pocket 10. Pocket 7 11. Pocket 8 16. Reject Pocket LED 17. Note Press 4. Pocket 1 18. Note Guide 5. Pocket 2 6. Pocket 3 19. Main SW 7. Pocket 4 20. Hopper 12. Operation Panel 13. START/STOP SW 21. Dust Tray 1 14. Note Press SW Description of Each Part...
Page 16
Chapter 1 OVERALL DESCRIPTIONS K4/K8 1. Pocket LED ......indicates status of pocket by lighting or blinking. Please refer to Indication of Pocket Status(P.6). 2. Status LED ......indicates a category of note at the Pocket. Please refer to Indication of Pocket Status (P.6). 3. Sub-Display ......indicates quantity of notes at the Pocket.
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Indication of Pocket Status Only for K4 1. Status LED 2. Pocket LED 3. Pocket Count Display Only for K8 1. Status LED 2. Pocket LED 3. Pocket Count Display Description of Each Part...
Page 19
K4/K8 Chapter 1 OVERALL DESCRIPTIONS 1. Status LED ......LED indicates note category by color of light. Blue Green Orange Sorting Mode FITNESS ─ Unfit Unfit SORT(Denom.) Single Mixed ─ FACE ─ ─ ORIENT ─ ─ ISSUE(Old/New) 2 generation old 2. Pocket LED ......guides operators to remove notes. When it is ready for removing them, LED lights on after ...
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Description of Display Stand-by Display Stand-by Display indicates present sorting mode, preset number and ♦ target currency. While showing Stand-by Display, the count starts by pressing START/ ♦ STOP SW. Present mode Present sorting pattern Status Information Press F1 key System Info to indicate Total count results. It indicates total number of notes counted by validator. Back to Stand-by Display.
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Count Display When counting starts, the display turns from Stand-by Display to Count ♦ Display and count result will be shown. Present mode Acceptable operation or pocket status. Pocket status Blinking: The Pocket is full. Lighting: A note remains. Count results in value and pieces. Press F1 key Info to indicate each pocket count results. Preset Number Denomination Description of Display...
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Guidance for Cleaning When the cleaning is required, the display indicates Cleaning Guidance ♦ on the display after turning on the power. If the Cleaning Guidance is indicated, clean the dust trays. Refer to Cleaning (P.49) for further details about cleaning. Only for K4 Only for K8 Description of Display...
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Error Display If a note jam occurs, the display switches Error Display and the display ♦ indicates error code and error location by graphic guidance. Refer to How to clear an error(P.56) and clear the error. ♦ Only for K4 Error code. Detailed Error code. Highlighting where notes remain. Blinking where an error occurs. After removing all remaining notes, press F5 key below the reset icon to reset the error. Only for K8 Error code. Detailed Error code. Highlighting where notes remain. Blinking where an error occurs. After removing all remaining notes, press F5 key below the reset icon to reset the error. Description of Display...
Chapter 1 OVERALL DESCRIPTIONS K4/K8 Description of Sorting Mode and Sorting Pattern About mode of sorting Following modes are available. ♦ 1) FITNESS Mode ....... Sorting out fit and unfit notes. 2) ATM Mode ........ Sorting out ATM-fit notes. 3) SORT Mode ......Sorting out denominations. 4) FACE/ORIENTATION Mode ..Sorting out facing or orientation of notes. 5) ISSUE Mode ......Sorting out new and old issue of notes by each generation. FITNESS Mode Only for K4 Press FITNESS key to activate FITNESS Mode and display indicates ♦...
Page 25
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 Press FITNESS key to activate FITNESS Mode and display indicates ♦ sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F1 key or F4 key to select the display screen. Press F2 key or F3 ♦ key to set sorting pattern. The contents of sorting patterns are following. Sorting Pattern Pocket Pocket 1 Fit(Face) Fit(Face) Fit1 Fit1 Fit(A) Pocket 2 Fit(Face)...
Chapter 1 OVERALL DESCRIPTIONS K4/K8 ATM Mode Only for K4 Press ATM key to activate ATM Mode and display indicates sorting ♦ pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F1 key to F3 key to set sorting pattern. The contents of sorting ...
Page 27
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 Press ATM key to activate ATM Mode and display indicates sorting ♦ pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F1 key or F4 key to select the display screen. Press F2 key or F3 ♦ key to set sorting pattern. The contents of sorting patterns are following. Sorting Pattern Pocket Pocket 1 ATM(Face) ATM(Face) Pocket 2 ATM(Face) ATM(Face) Pocket 3 ATM (Unface)ATM (Unface)...
Chapter 1 OVERALL DESCRIPTIONS K4/K8 SORT Mode Only for K4 Press SORT key to activate SORT Mode and display indicates sorting ♦ pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F1 key to F4 key to set sorting pattern. The contents of sorting ...
Page 29
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 Press SORT key to activate SORT Mode and display indicates sorting ♦ pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F1 key or F4 key to select the display screen. Press F2 key or F3 ♦ key to set sorting pattern. The contents of sorting patterns are following. Sorting Pattern Pocket Pocket 1 Other Pocket 2 Other Pocket 3 Other Pocket 4 Other Pocket 5...
Chapter 1 OVERALL DESCRIPTIONS K4/K8 FACE/ORIENTATION Modes Only for K4 Press FACE/ORIENT key to activate FACE/ORIENTATION Mode and ♦ display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F1 key or F2 key to set sorting pattern. The contents of sorting ♦ ...
Page 31
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 Press FACE/ORIENT key to activate FACE/ORIENTATION Mode and ♦ display indicates sorting pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F2 key or F3 key to set sorting pattern. The contents of sorting ♦ patterns are following.
Chapter 1 OVERALL DESCRIPTIONS K4/K8 ISSUE Mode Only for K4 Press ISSUE key to activate ISSUE Mode and display indicates sorting ♦ pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F1 key or F2 key to set sorting pattern. The contents of sorting ...
Page 33
K4/K8 Chapter 1 OVERALL DESCRIPTIONS Only for K8 Press ISSUE key to activate ISSUE Mode and display indicates sorting ♦ pattern for each pocket. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Press F2 key or F3 key to set sorting pattern. The contents of sorting ...
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Starting-up and Closing-down of the Unit The unit starts up by turning on Main SW. Turn OFF Main SW when ♦ closing the Unit. The self-check function activates when the power is on. When no error is ♦ found in self-check, the stand-by display is indicated and gets ready for counting. Only for K4 Stand-by Display Ex. Fitness Only for K8 Stand-by Display ...
Page 37
K4/K8 Chapter 2 DESCRIPTION OF OPERATION If an error is found in self-check, Error Display is indicated. Clear the error ♦ according to the error showing on the display. Refer to Setting of Sorting Modes and Sorting Pattern (P.29). Only for K4 Only for K8 If the dust tray cleaning is required, Maintenance Info Display is indicated ♦ after turning on the power. Clean the dust trays according the information showing on the display. Without cleaning dust trays, the display does not show Stand-by Display. Refer to Cleaning (P.49). Starting-up and Closing-down of the Unit...
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Count If necessary change Sorting Mode or Sorting Pattern. STEP-1 Refer to Setting of Sorting Modes and Sorting Pattern (P.29) for further details. Only for K4 Only for K8 FUNCTION FITNESS FUNCTION FITNESS FITNESS FITNESS SETTINGS SETTINGS SORT SORT SETTINGS SETTINGS FACE FACE ORIENT ORIENT DISPLAY DISPLAY ISSUE ISSUE FUNCTION FITNESS FUNCTION FITNESS FITNESS FITNESS SETTINGS...
Page 39
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Adjust Note Guide to size of note. STEP-3 ▷ Move Note Guide by holding rib part. rib part STEP-4 Align the notes and put the notes onto the Hopper. ▷ The count starts automatically. ▷ I f t h e c o u n t d o e s n o t s t a r t ...
Page 40
Chapter 2 DESCRIPTION OF OPERATION K4/K8 STEP-5 When completing the transaction after the count, be sure no note on the Hopper and press START/ STOP switch. ▷ When START/STOP switch is p r e s s e d w i t h o u t n o t e a t t h e ...
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Setting of Sorting Modes and Sorting Pattern Press sorting key to set a Sorting Mode. STEP-1 Only for K4 Only for K8 Ex. Fitness Ex. Fitness FUNCTION FITNESS FUNCTION FITNESS FITNESS FITNESS SETTINGS SETTINGS SORT SORT SETTINGS SETTINGS FACE FACE ORIENT ORIENT DISPLAY DISPLAY ISSUE ISSUE STEP-2 Ex. Fitness Only for K4 Press F1 key to F4 key to select FUNCTION FITNESS sorting pattern. FITNESS SETTINGS SORT ▷ ...
Page 42
Chapter 2 DESCRIPTION OF OPERATION K4/K8 STEP-3 Press F5 key to return to Stand-by Display. Only for K4 Only for K8 Ex. Fitness Ex. Fitness FUNCTION FITNESS FUNCTION FITNESS FITNESS FITNESS SETTINGS SETTINGS SORT SORT SETTINGS SETTINGS FACE FACE ORIENT ORIENT DISPLAY DISPLAY ISSUE ISSUE Setting of Sorting Modes and Sorting Pattern...
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Setting of Preset Number If the display indicates sorting pattern, press F5 key Exit to return STEP-1 to Stand-by Display. Only for K4 Only for K8 Ex. Fitness Ex. Fitness FUNCTION FITNESS FUNCTION FITNESS FITNESS FITNESS SETTINGS SETTINGS SORT SORT SETTINGS SETTINGS FACE FACE ORIENT ORIENT DISPLAY DISPLAY ISSUE...
Page 44
Chapter 2 DESCRIPTION OF OPERATION K4/K8 STEP-4 Press F5 key Exit to return to Stand-by Display after saving the preset number. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Setting of Preset Number...
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Total Function When option printer is connected, a result of count can be printed out. ♦ 1) Grand Total ...... It indicates Ground Total. 2) Operator Record ..It indicates count Record per operator. 3) Fitness Record ....It indicates percentage of fit and unfit result. 4) History ....... It indicates Record of operations. *1) In order to activate this function, it is necessary to set OP function on in ...
Page 46
Chapter 2 DESCRIPTION OF OPERATION K4/K8 When printing out (Option) 1. Press F3 key Print . FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE ▷ The display indicates printing screen. It returns back to previous screen after completing print out. When clearing data 1. Press F1 key Clear . FUNCTION FITNESS ▷ The display indicates data clear FITNESS SETTINGS screen.
Page 47
K4/K8 Chapter 2 DESCRIPTION OF OPERATION 3. Input operator number by F3 key − or F4 key + . FUNCTION FITNESS Press F2 key to move the cursor ♦ FITNESS SETTINGS to desired digit. SORT SETTINGS FACE ORIENT 4. Press F1 key ENT . DISPLAY ISSUE ▷ The display indicates total for selected operator. When printing out (Option) 1. Press F3 key Print .
Page 48
Chapter 2 DESCRIPTION OF OPERATION K4/K8 When clearing data 1. Press F1 key Clear . FUNCTION FITNESS ▷ The display indicates data clear FITNESS SETTINGS screen. SORT SETTINGS FACE ORIENT DISPLAY ISSUE 2. Press F1 key ENT . ▷ T h e d i s p l a y r e t u r n s b a c k t o ...
Page 49
K4/K8 Chapter 2 DESCRIPTION OF OPERATION When printing out (Option) 1. Press F3 key Print . FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE ▷ The display indicates printing screen. It returns back to previous screen after completing print out. Total Function...
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Setting of Fitness Level STEP-1 Press FITNESS SETTING key while the display is showing Stand-by Display. ▷ The display indicates Fitness Setting Display. ▷ If Admin Mode is activated, the password is required. Only for K4 Only for K8 Ex. Fitness Ex. Fitness FUNCTION FITNESS FUNCTION FITNESS FITNESS FITNESS SETTINGS SETTINGS SORT SORT SETTINGS SETTINGS FACE FACE ORIENT ORIENT DISPLAY...
Page 51
K4/K8 Chapter 2 DESCRIPTION OF OPERATION 3. Move the cursor to your desired Fitness Level by F1 key or F2 key. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE ▷ If L, M, H or (EU) of ALL is selected, Fitness Level of all denominations will be set all together. FUNCTION FITNESS FITNESS 4. Skip STEP-3 and go to STEP-4. SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE STEP-3 Detailed Fitness Level Setting 1. P r e s s F I T N E S S S E T T I N G k e y ...
Page 52
Chapter 2 DESCRIPTION OF OPERATION K4/K8 STEP-4 Press F5 key Exit to return the display to Stand-by Display. FUNCTION FITNESS ▷ Fitness Level is memorized. FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE Setting of Fitness Level...
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Setting of CF Level CF Level means the level of security feature detection. ♦ STEP-1 Press CF SETTING key while the display is showing Stand-by Display. ▷ CF Setting Display is indicated. ▷ If Admin Mode is activated, the password is required. Only for K4 Only for K8 Ex. Fitness Ex. Fitness FUNCTION FITNESS FUNCTION FITNESS FITNESS FITNESS SETTINGS SETTINGS SORT SORT SETTINGS SETTINGS FACE FACE ORIENT ORIENT DISPLAY DISPLAY ISSUE ISSUE How to input the password. 1. Press F1 key or F2 key to select ...
Page 54
Chapter 2 DESCRIPTION OF OPERATION K4/K8 3. Move the cursor to desired CF Level by F1 key or F2 key. FUNCTION FITNESS 4. Skip STEP-3 and go to STEP-4. FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE STEP-3 Detailed CF Level Setting 1. Press CF SETTING key again while FUNCTION FITNESS the display is showing CF Setting FITNESS SETTINGS D i s p l a y . D e t a i l e d C F S e t t i n g ...
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Function Setting 1) Currency ..Currency Selection. 2) Language ..Language Selection. 3) Contrast ..Contrast Setting of Main-Display. 4) Back Light ..Time Setting of Back Light saving mode. 5) Buzzer ..... Volume Setting of Buzzer. 6) Date ....Date Setting of internal clock. 7) Time ....Time Setting of internal clock. 8) Printer ..... Printer Setting(Printer is option.) 9) Admin ....Admin Mode Setting. Press FUNCTION key while the display is showing Stand-by Display.
Page 56
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Language 1. M o v e t h e c u r s o r t o s e l e c t Language by △ Key or ▽ key. FUNCTION FITNESS FITNESS 2. M o v e t h e c u r s o r t o d e s i r e d ...
Page 57
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Date 1. Move the cursor to Date by △ Key FUNCTION FITNESS or ▽ key. FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE 2. Move the cursor to year, month or day by F1 key or F2 key. FUNCTION FITNESS 3. Change the value by F3 key − or FITNESS SETTINGS F4 key + . SORT SETTINGS FACE ORIENT DISPLAY ISSUE Time 1.
Page 58
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Printer Regarding printer connection, please contact your regional distributors. ♦ The following describes the setting after connecting a printer. ♦ 1. Move the cursor to Printer by △ Key or ▽ key. FUNCTION FITNESS 2. Press F3 key ENT . FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE 3. Move the cursor to Printer by △ Key or ▽ key. FUNCTION FITNESS 4. Set it to ON by F1 key or F2 key.
Page 59
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Admin 1. Move the cursor to Admin by △ Key FUNCTION FITNESS or ▽ key. FITNESS SETTINGS SORT 2. Press F3 key ENT . SETTINGS FACE ORIENT DISPLAY ▷ P a s s w o r d I n p u t D i s p l a y i s ...
Page 60
Chapter 2 DESCRIPTION OF OPERATION K4/K8 In order to change password 4-1. Move the cursor to Password FUNCTION FITNESS Setting by △ Key or ▽ key. FITNESS SETTINGS SORT 4-2. Press F3 key ENT . SETTINGS 4-1. FACE ORIENT DISPLAY ISSUE 4-2. 4-3. Input the current password and new password. FUNCTION FITNESS ▷ FUNCTION display is indicated ...
K4/K8 Chapter 2 DESCRIPTION OF OPERATION Cleaning Periodical Cleaning and Position Clean the Dust Trays at least once in a day. Dust Tray 1 and Dust Tray 2 ♦ Clean the Transportation Path 1 and the Validator periodically. ♦ Cleaning the Dust Tray 1 Hold the handle of Dust Tray 1 STEP-1 and pull it out. Remove the dust in the Dust Tray 1. STEP-2 Set the Dust Tray 1 back to the unit. Cleaning ...
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Cleaning the Dust Tray 2 STEP-1 Open the Front Door by the handle. Only for K4 Only for K8 STEP-2 Pull out Dust Tray 2 by holding green parts. Remove the dust in the Dust Tray 2. Dust Tray 2 Set the Dust Tray 2 back to the STEP-3 unit. Cleaning ...
Page 63
K4/K8 Chapter 2 DESCRIPTION OF OPERATION STEP-4 Close the Front Door. Only for K4 Only for K8 Cleaning ...
Chapter 2 DESCRIPTION OF OPERATION K4/K8 Cleaning Sensors STEP-1 Open the Front Door by the handle. Only for K4 Only for K8 STEP-2 Open the Transportation Path 1 and remove the dust. 1. Unlock the Transportation Path 1 by lever 1 and open it. Lever 1 2. Clean the transportation path by cotton swab or brush. To remove the dust. Cleaning ...
Page 65
K4/K8 Chapter 2 DESCRIPTION OF OPERATION 3. Close the Transportation Path 1 gently by holding lever 1. Be sure to lock the Transportation ♦ Path 1 by locking lever 1. Open the Validator and clean the STEP-3 sensors. 1. Unlock the clamp of Validator. Lever 3 2. Open Validator with holding lever 3. Clamp 3. Clean the Validator by cotton swab or brush. To clean the sensors. To clean the sensors. 4. Open the Transportation Path 2 ...
Page 66
Chapter 2 DESCRIPTION OF OPERATION K4/K8 5. Close the Transportation Path 2 gently. 6. Close the Validator by holding lever 7. Lock the Validator by clamp. Lever 3 Clamp Close the Front Door. STEP-4 Only for K4 Only for K8 Cleaning ...
Chapter 3 IF AN ERROR OCCURS K4/K8 How to clear an error This chapter describes action to be taken when an error occurs. Error Display If an error occurs such as note jam, the main-display switches to Error ♦ Display which shows error code and location of the error by guidance. In order to clear the error, check the error code and location of error and ♦ take remedial action correspond to Error and Remedial Measure page 49. Error Code 61 Error Detail Code 30-12. Only for K4 Error Display The guidance is emphasized where notes remains. The location of error blinks. Reset icon appears when it is valid. Error Code 61 Error Detail Code 30-12. Only for K8 Error Display The guidance is emphasized where notes remains.
K4/K8 Chapter 3 IF AN ERROR OCCURS Error and Remedial Measure Error Code Content of Error Remedial Measure 1. Remove remaining notes according to the guidance on the display. 2. Press Reset key. 3. If the notes are discharged to the pockets Error 10 to 32 Mechanical Error after the reset actions, remove the notes from the pockets. Refer to How to remove jam notes (P.58). 1. Remove remaining note according to the ...
Chapter 3 IF AN ERROR OCCURS K4/K8 How to remove jam notes Description of Guidance Only for K4 Upper Transportation Unit(P.67) Pocket Transportation Unit 1(P.72) Reject Pocket(P.59) Pocket(P.60) Hopper(P.59) Main Transportation Unit(P.63) Feed Unit(P.61) Only for K8 Pocket Transportation Unit 1(P.72) Upper Transportation Unit(P.67) Pocket Transportation Unit 2 (Only for K8) (P.76) Reject Pocket(P.59) Pocket(P.60) Hopper(P.59) Main Transportation Unit(P.63) Feed Unit(P.61) How to remove jam notes...
K4/K8 Chapter 3 IF AN ERROR OCCURS Hopper Remove all the notes from the STEP-1 Hopper. STEP-2 Press F5 key Reset . ▷ The reset action gets started. FUNCTION FITNESS FITNESS ▷ Stand-by Display is shown after SETTINGS SORT SETTINGS c o m p l e t i n g t h e r e s e t a c t i o n ...
Chapter 3 IF AN ERROR OCCURS K4/K8 STEP-2 Press F5 key Reset . ▷ The reset action gets started. FUNCTION FITNESS FITNESS ▷ Stand-by Display is shown after SETTINGS SORT SETTINGS c o m p l e t i n g t h e r e s e t a c t i o n ...
K4/K8 Chapter 3 IF AN ERROR OCCURS Feed Unit STEP-1 Open the Front Door by the handle. Only for K4 Only for K8 STEP-2 R e m o v e r e m a i n e d n o t e b y opening the Transportation Path 1. H o l d L e v e r 1 t o u n l o c k t h e ...
Page 74
Chapter 3 IF AN ERROR OCCURS K4/K8 3. By holding the Lever 1, close the Transportation Path 1 gently. Release the Lever 1 and make ♦ sure that the Transportation Path 1 gets locked. Close the Front Door. STEP-3 ▷ The reset action gets started. ▷ Stand-by Display is shown after completing the reset action normally. Only for K4 Only for K8 ▷ If the reset action does not gets ...
K4/K8 Chapter 3 IF AN ERROR OCCURS Main Transportation Unit Open the Front Door by the handle. STEP-1 Only for K4 Only for K8 STEP-2 Open the Upper Door and be sure to lock the door kept open. Only for K4 Only for K8 STEP-3 Open the Transportation Path 4, 1. Unlock Transportation Path 4 by pressing Lever 4 in the direction to arrow mark. 2. Open Transportation Path 4 till Lever 4 locking the position. Transportation Path 4 How to remove jam notes...
Page 76
Chapter 3 IF AN ERROR OCCURS K4/K8 STEP-4 O p e n t h e V a l i d a t o r U n i t a n d remove remained notes. 1. Release the clamp of Validator Lever 3 Unit. 2. Open the Validator Unit by holding ...
Page 77
K4/K8 Chapter 3 IF AN ERROR OCCURS STEP-5 Close the Validator Unit. 1. Close the Validator Unit by the Lever 3. Lever 3 2. Lock Validator Unit by clamp. Clamp Close the Transportation Path 4. STEP-6 1. Keep up the Transportation Path 4 by the Lever 4 and unlock by pressing Lever 5. 2. Close the Transportation Path 4 Lever 4 gently.
Page 78
Chapter 3 IF AN ERROR OCCURS K4/K8 STEP-8 Close the Upper Door. 1. Keep up the Upper Door by the handle to unlock by pressing Lever 6. 2. Close the Upper Door gently. ▷ The reset action gets started. ▷ Stand-by Display is shown after completing the reset action normally. Lever 6 Lever 6 Handle Handle Only for K4 Only for K4 ▷ If the reset does not get started, press F5 key to activate the reset. FUNCTION FITNESS FITNESS SETTINGS SORT SETTINGS FACE ORIENT DISPLAY ISSUE How to remove jam notes...