Advertisement
DO NOT hold unsecured work in your hand and DO NOT touch the grinding disc whilst operating, or whilst plugged into the mains power.
8
DO NOT leave the grinder running unattended, and DO NOT lay the grinder down whilst it is running.
8
DO NOT operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
When not in use switch off grinder, remove plug from power supply and store in safe, dry, childproof area.
9
WARNING! The grinding process can produce streams of sparks which are a potential source of ignition, especially when
‰
grinding metal.
DO NOT use the grinder where there are flammable liquids, solids or gases.
8
DO NOT allow grinder sparks to make contact with the operator's clothing or any other fabric such as cleaning rags. Fabrics
8
contaminated with flammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in
9
preference to man-made fibres.
2. INTRODUCTION
Angle grinder with alloy drive casing and composite motor housing. Smooth running motor and bevel gears give low operating noise and
vibration. Models feature an integral spindle lock for fast loading/unloading of grinding discs. Slider type power control with power lock.
Supplied with side handle, guard and spanner. Grinding disc not included, order model no. PTC/115G.
3. SPECIFICATION
Model no: ................................................................. S0530.V2
Disc size: .................................................................. Ø115mm
Spindle size: ......................................................... M14 x 2mm
Motor power: ...................................................................600W
Supply: .............................................................................230V
No load speed:......................................................... 11000rpm
Nett Weight: .................................................................... 2.1kg
Noise power: ..................................................................100dB
Noise pressure:................................................................89dB
Vibration: ................................................................. 4.646m/s²
Uncertainty: ................................................................. 1.5m/s²
4. CONTENTS
1.
Angle grinder
2.
Safety guard
3.
Disc flange
4.
Nut flange
5.
Auxiliary handle
6.
Disc spanner
5. ASSEMBLY
WARNING! Ensure that the grinder is unplugged from the mains
‰
power supply before assembling.
5.1.
FIT GRINDING DISC
(only to be performed by person holding grinding wheel certificate)
5.1.1.
Place the disc flange (fig.5.8) onto the centre spindle (fig.5.A)
ensuring that the joint ring (fig.5.9) is facing away from the grinder.
5.1.2.
Engage the recess in the disc flange with the drive flats on the shaft.
5.1.3.
Place grinding disc on the spindle.
5.1.4.
Retain disc with nut flange. Fit with spigot facing out if disc is less
than 5mm thick, and facing in if disc is more than 5mm thick (fig.2 & 3).
5.1.5.
Stop the spindle from turning by pushing in and holding the
locking button (fig.4).
5.1.6.
Lock the grinding disc into place by tightening the nut flange (fig.5.10) with the disc spanner (fig.5.11).
5.1.7.
Release the locking button and check that it has sprung back to the initial position.
5.2.
POSITIONING THE GUARD
5.2.1.
The guard may be rotated through any angle to suit the task.
5.2.2.
Position the guard to give working access whilst still providing maximum protection for the operator.
5.2.3.
Lock the guard in place by tightening locking bolt (fig.4).
5.3.
HANDLE
5.3.1.
The auxiliary handle will allow better control and safety.
5.3.2.
Fit the handle by screwing it into the threaded hole on either the left or right side of the gear box, as best suits the work.
6. GRINDING DISCS
WARNING! DO NOT USE DISCS THAT ARE DAMAGED, OR SUSPECTED OF DAMAGE.
‰
Before using a grinding disc ensure there are no fissures or cracks. Once mounted on the grinder test the disc before use by facing the
grinder in a safe direction (pointing away from yourself, others and vulnerable items) and operate for a short time.
DANGER! Use of damaged discs may cause damage and/or personal injury.
▲
Grinding and cutting discs used in association with this machine shall be of an adequate speed rating and suitable for the job
in hand.
The discs should be manufactured in accordance with British Standard 4481:Part 1 1989.
Only persons holding a grinding wheel certificate are authorised to change grinding discs.
© Jack Sealey Limited
DANGER OF FIRE/EXPLOSION HAZARD
Model no: ............................................................... S0685.V2
Disc size:................................................................. Ø115mm
Spindle size: ........................................................ M14 x 2mm
Motor power: .................................................................860W
Supply: ...........................................................................230V
No load speed: ....................................................... 11000rpm
Nett Weight: .................................................................. 2.3kg
Noise power: ................................................................100dB
Noise pressure: ..............................................................89dB
Vibration: ................................................................ 4.646m/s²
Uncertainty: ................................................................ 1.5m/s²
Original Language Version
S0530.V2, S0685.V2 | Issue 4 (H,F) 24/10/2018
fig.1
Advertisement
