Page 2
This Owner’s Manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.
TABLE OF CONTENTS INTRODUCTION ..........................8 GETTING TO KNOW YOUR VEHICLE ................. 10 GETTING TO KNOW YOUR INSTRUMENT PANEL ............67 SAFETY ............................92 STARTING AND OPERATING ....................146 IN CASE OF EMERGENCY .....................194 SERVICING AND MAINTENANCE ..................234 TECHNICAL SPECIFICATIONS .................... 287 MULTIMEDIA ..........................301 CUSTOMER ASSISTANCE .....................369 INDEX .............................
Page 4
INTRODUCTION MIRRORS ..............37 VEHICLE SECURITY ALARM — IF EQUIPPED .. 22 To Arm The System........22 Automatic Dimming Mirror......37 HOW TO USE THIS MANUAL........8 To Disarm The System ........ 23 Outside Mirrors .......... 37 Essential Information ........8 Rearming Of The System......
Page 5
INTERNAL EQUIPMENT........63 CLIMATE CONTROLS ...........44 EMISSIONS INSPECTION AND MAINTENANCE Automatic Climate Control Overview ..45 Storage ............63 PROGRAMS ............90 Climate Control Functions......51 Cupholders ........... 64 SAFETY Automatic Temperature Control (ATC) ..51 Electrical Power Outlets ......64 Operating Tips ..........
Page 6
STARTING AND OPERATING PARKSENSE REAR PARK ASSIST — FUEL SAVER TECHNOLOGY 5.7L AND 6.4L ONLY — IF EQUIPPED.........163 IF EQUIPPED ............. 178 STARTING THE ENGINE ........146 ELECTRIC POWER STEERING ......163 ParkSense Sensors ........178 Manual Transmission — If Equipped ..146 ParkSense Warning Display......
Page 7
DRIVING TIPS ............. 192 TIRE SERVICE KIT — IF EQUIPPED ....221 ENGINE COMPARTMENT ........ 245 Driving On Slippery Surfaces.....192 Tire Service Kit Storage......221 3.6L Engine ..........245 Driving Through Water ......193 Tire Service Kit Components And 5.7L Engine ..........246 Operation............222 6.2L Supercharged Engine ...... 247 IN CASE OF EMERGENCY Tire Service Kit Usage Precautions ..222 6.4L Engine ..........248...
Page 8
TECHNICAL SPECIFICATIONS MULTIMEDIA RAISING THE VEHICLE ........266 TIRES ..............266 IDENTIFICATION DATA........287 UCONNECT SYSTEMS ........301 Tire Safety Information ......266 Vehicle Identification Number ....287 CYBERSECURITY ..........301 Tires — General Information .....273 BRAKE SYSTEM ..........287 UCONNECT SETTINGS ........302 Tire Types ...........277 WHEEL AND TIRE TORQUE SPECIFICATIONS 287 Customer Programmable Features —...
Page 9
Voice Text Reply — If Equipped ....365 IF YOU NEED ASSISTANCE .......369 REPORTING SAFETY DEFECTS ......371 Climate ............366 FCA US LLC Customer Center ....369 In The 50 United States And Navigation (4C NAV) ........366 FCA Canada Inc. Customer Center ...370 Washington, D.C.
INTRODUCTION HOW TO USE THIS MANUAL This Owner's Manual describes all versions of Dear Customer, this vehicle. Options and equipment dedicated Congratulations on selecting your new vehicle. Essential Information to specific markets or versions are not expressly Be assured that it represents precision work- indicated in the text.
INTRODUCTION WARNINGS AND CAUTIONS WARNING! WARNING! This Owner’s Manual contains WARNINGS To prevent SERIOUS INJURY or DEATH when To prevent SERIOUS INJURY or DEATH: against operating procedures that could result using “Track-Use” parts and equipment: ALWAYS remove any “Track-Use” equip- ...
GETTING TO KNOW YOUR VEHICLE VEHICLE USER GUIDE — IF EQUIPPED while the vehicle is in motion, the system will Features/Benefits display the message “Feature not available Pre-installed on your Uconnect touchscreen Access your Owner’s Information right through while the vehicle is in motion”. radio your Uconnect 4C or 4C NAV touchscreen Pre-Installed Features...
GETTING TO KNOW YOUR VEHICLE KEYS Key Fob The key fob allows you to lock or unlock the doors and trunk from distances up to approxi- mately 66 ft (20 m). The key fob does not need to be pointed at the vehicle to activate the system.
Page 14
GETTING TO KNOW YOUR VEHICLE NOTE: To change the current setting, refer to All door unlock settings can be programmed to “Uconnect Settings” in “Multimedia” for further your convenience through Uconnect Settings. information. Refer to “Uconnect Settings” in “Multimedia” Flash Lights With Lock for further information.
Page 15
GETTING TO KNOW YOUR VEHICLE To Lock The Doors And Trunk Using The Panic Alarm Key Fob Battery Replacement Push and release the lock button on the key fob To turn the Panic Alarm feature on or off, push The recommended replacement battery is one to lock all doors.
Page 16
GETTING TO KNOW YOUR VEHICLE 1. Remove the emergency key by sliding the NOTE: mechanical latch on the back of the key Separating the case can also be done with the fob sideways with your thumb and then pull emergency key or a flat head screwdriver. the emergency key out with your other hand.
Page 17
GETTING TO KNOW YOUR VEHICLE Programming Additional Key Fobs Duplication of key fobs may be performed at an authorized dealer. This procedure consists of Programming the key fob may be performed by programming a blank key fob to the vehicle an authorized dealer.
GETTING TO KNOW YOUR VEHICLE IGNITION SWITCH Le présent appareil est conforme aux CNR d`Innovation, Science and Economic Develop- Keyless Push Button Ignition ment applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux This feature allows the driver to operate the igni- conditions suivantes: tion with the push of a button as long as the key fob is in the passenger compartment.
GETTING TO KNOW YOUR VEHICLE ON/RUN NOTE: WARNING! (Continued) The power window switches and power sunroof Driving position. (if equipped) will remain active for three Do not leave children or animals inside All the electrical devices are available. ...
GETTING TO KNOW YOUR VEHICLE To drive the vehicle, push the unlock button, Vehicle alarm system indicator flashing WARNING! (Continued) and place the ignition in the ON/RUN position. Ignition in STOP/OFF position Do not leave the key fob in or near the ...
GETTING TO KNOW YOUR VEHICLE Remote Start Abort Message On The NOTE: NOTE: To avoid unintentional shutdowns, the system Instrument Cluster Display — If Equipped If an engine fault is present or fuel level is will disable for two seconds after receiving a The following messages will display in the low, the vehicle will start and then shut down valid remote start request.
GETTING TO KNOW YOUR VEHICLE and Turn To Run” will show in the instrument will automatically turn on in cold weather. In 1. l'appareil ne doit pas produire de brouil- cluster display until you insert the key. warm weather, the driver vented seat feature lage, et will automatically turn on when the remote start For vehicles equipped with the Keyless...
GETTING TO KNOW YOUR VEHICLE The system uses a key fob, keyless push button CAUTION! CAUTION! ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation. There- The Sentry Key Immobilizer system is not Always remove the key fobs from the ...
GETTING TO KNOW YOUR VEHICLE General Information La operación de este equipo está sujeta a las To Arm The System siguientes dos condiciones: The following regulatory statement applies to all Follow these steps to arm the vehicle security Radio Frequency (RF) devices equipped in this alarm: 1.
GETTING TO KNOW YOUR VEHICLE DOORS Security System Manual Override alarm. If one of the previously described arming sequences has occurred, the vehicle security The vehicle security alarm will not arm if you Manual Door Locks alarm will arm regardless of whether you are in lock the doors using the manual door lock.
GETTING TO KNOW YOUR VEHICLE Refer to “Keyless Enter-N-Go — Passive Entry” in WARNING! WARNING! (Continued) this section for further information. For personal security and safety in the Do not leave the key fob in or near the If you push the power door lock switch while the event of a collision, lock the vehicle doors vehicle, or in a location accessible to chil-...
Page 27
GETTING TO KNOW YOUR VEHICLE If the vehicle is unlocked by Passive Entry NOTE: and no door is opened within 60 seconds, the All doors will unlock when the front passenger vehicle will re-lock and if equipped will arm door handle is grabbed regardless of the the security alarm.
Page 28
GETTING TO KNOW YOUR VEHICLE When any of these situations occur, after all open doors are shut, the FOBIK-Safe search will be executed. If it finds a Passive Entry key fob inside the car, and it does not find any Passive Entry key fobs outside the car, the car will unlock and alert the customer.
GETTING TO KNOW YOUR VEHICLE NOTE: 1. This device may not cause harmful interfer- NOTE: ence, and Changes or modifications not expressly After pushing the door handle button, you approved by the party responsible for compli- must wait two seconds before you can lock or 2.
GETTING TO KNOW YOUR VEHICLE Automatic Door Locks — If Equipped Manual Adjustment (Front Seats) — If Equipped The auto door lock feature default condition is enabled. When enabled, the door locks will lock WARNING! automatically when the vehicle's speed exceeds 15 mph (24 km/h).
GETTING TO KNOW YOUR VEHICLE Manual Front Seat Recline Manual Adjustment (Rear Seats) To adjust the seatback, lift the lever located on Folding Rear Seat the outboard side of the seat, lean back to the The rear seatbacks can be folded forward to desired position and release the lever.
GETTING TO KNOW YOUR VEHICLE Adjusting The Seat Forward Or Rearward switch upward or downward to raise or lower the WARNING! (Continued) lumbar support. The seat can be adjusted both forward and rear- The cargo area in the rear of the vehicle ...
GETTING TO KNOW YOUR VEHICLE If the HI-level setting is selected, the system will WARNING! WARNING! (Continued) automatically switch to LO-level after approxi- mately 60 minutes of continuous operation. At Persons who are unable to feel pain to the Do not place anything on the seat or seat- ...
GETTING TO KNOW YOUR VEHICLE The front ventilated seats control buttons are passenger. If the passenger and/or rear seats WARNING! (Continued) located within the Uconnect system. You can have been removed, do not ride in those areas. gain access to the control buttons through the Only ride in available seating positions This vehicle has been designed to maximize ...
GETTING TO KNOW YOUR VEHICLE Passenger Seat Easy Entry NOTE: WARNING! On the passenger seat, pull forward on the lever The front passenger seat needs to slide back All occupants, including the driver, should located on the side of the seatback in order to to a pre-set position for the fore-aft adjuster not operate a vehicle or sit in a vehicle’s dump the seatback and slide the seat forward.
GETTING TO KNOW YOUR VEHICLE The RHR will automatically return to their the base of each post while pulling the head WARNING! (Continued) normal position following a rear impact. If the restraint up. To reinstall the head restraint, put RHR do not return to their normal position, see the head restraint posts into the holes while Do not place items over the top of the Reac- ...
GETTING TO KNOW YOUR VEHICLE to lengthen or shorten the steering column. The WARNING! WARNING! (Continued) tilt/telescoping lever is located below the If the passenger and/or rear seats have steering wheel at the end of the steering Be sure everyone in your vehicle is in a seat ...
GETTING TO KNOW YOUR VEHICLE To tilt the steering column, move the switch up Press the heated steering wheel button WARNING! or down as desired. To lengthen or shorten the once to turn the heating element on. Do not adjust the steering column while steering column, pull the switch toward you or Press the heated steering wheel button driving.
GETTING TO KNOW YOUR VEHICLE The Automatic Dimming feature can be turned Outside Mirrors WARNING! (Continued) on or off through the touchscreen. To receive maximum benefit, adjust the outside Do not place anything on the steering wheel Press the mirror dimmer button once to turn ...
GETTING TO KNOW YOUR VEHICLE Power Mirrors Using the mirror control switch, push on any of “Slide-On-Rod” And Extender Features Of the four arrows for the direction that you want Sun Visor The power mirror controls are located on the the mirror to move.
GETTING TO KNOW YOUR VEHICLE EXTERIOR LIGHTS Multifunction Lever Lights can be turned on and off using the Uconnect System, refer to “Uconnect Settings” The multifunction lever controls the operation Headlight Switch in “Multimedia” for further information. of the turn signals, headlight beam selection The headlight switch is located on the left side and passing lights.
GETTING TO KNOW YOUR VEHICLE cause headlights to remain on longer (closer Automatic Headlights and the programmable feature is set to on. In to the vehicle). Also, dirt, film, and other addition, the headlights will turn off when the This system automatically turns the headlights obstructions on the windshield or camera wipers are turned off if they were turned on by on or off according to ambient light levels.
GETTING TO KNOW YOUR VEHICLE If you turn the headlights off before the ignition, To activate the front fog lights, turn on the A “Turn Signal On” message will appear in the they will turn off in the normal manner. parking lights or the low beam headlights and instrument cluster display and a continuous chime will sound if the vehicle is driven more...
GETTING TO KNOW YOUR VEHICLE Map/Reading Lights ness of the door handle lights, map pocket With the parking lights or headlights on, rotating lights, and ambient light located in the over- the left dimmer control upward will increase the These lights are mounted between the sun head console.
GETTING TO KNOW YOUR VEHICLE Parade Mode (Daytime Brightness Feature) Wiper Operation Intermittent Wiper System Rotate the instrument panel dimmer control Use the intermittent wiper when weather Rotate the end of the multifunction lever to the upward to the first detent. This feature conditions make a single wiping cycle with a first detent, past the intermittent settings for brightens all text displays such as the odom-...
GETTING TO KNOW YOUR VEHICLE washers of the vehicle ahead. Rotate the end of Low Ambient Temperature — When the igni- WARNING! tion is first placed in the ON position, the Rain the multifunction lever to one of four settings to Sudden loss of visibility through the activate this feature.
GETTING TO KNOW YOUR VEHICLE Automatic Climate Control Overview Uconnect 4 With 7–inch Display Automatic Climate Controls...
Page 48
GETTING TO KNOW YOUR VEHICLE Uconnect 4C/4C NAV With 8.4–inch Display Automatic Climate Controls NOTE: Interior trims may vary. Depending on the engine equipped in the vehicle, there may be a “DRAG”, “Drive Mode”, or “SRT” button in place of a “Sport” button on the instrument panel.
Page 49
GETTING TO KNOW YOUR VEHICLE Automatic Climate Control Descriptions Icon Description MAX A/C Button Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air. The MAX A/C indicator illuminates when MAX A/C is on. Pressing and releasing the button again will cause the MAX A/C operation to exit.
Page 50
GETTING TO KNOW YOUR VEHICLE Icon Description AUTO Button Set your desired temperature and press AUTO. AUTO will achieve and maintain your desired temperature by automatically adjusting the blower speed and air distribution. AUTO mode is highly recommended for efficiency. You can press and release this button on the touchscreen, or push the button on the faceplate, to turn AUTO on.
Page 51
GETTING TO KNOW YOUR VEHICLE Icon Description SYNC Button Press the Sync button on the touchscreen to toggle the Sync feature on/off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger temperature setting with the driver temperature setting. Changing the passenger temperature setting while in Sync will automatically exit this feature.
Page 52
GETTING TO KNOW YOUR VEHICLE Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.
GETTING TO KNOW YOUR VEHICLE Climate Control Functions ator), for an accumulation of dirt or insects. Automatic Temperature Control (ATC) Clean with a gentle water spray from the front A/C (Air Conditioning) Automatic Operation of the radiator and through the condenser. The Air Conditioning (A/C) button allows the 1.
GETTING TO KNOW YOUR VEHICLE The temperature can be displayed in U.S. or Winter Operation increase the front blower speed. Do not use the Metric units by selecting the U.S./Metric Recirculation mode without A/C for long To ensure the best possible heater and customer-programmable feature.
GETTING TO KNOW YOUR VEHICLE WINDOWS Cabin Air Filter CONTROL WEATHER The climate control system filters out dust and SETTINGS Power Window Controls pollen from the air. Contact an authorized Set the mode control dealer to service your cabin air filter, and to The window controls on the driver's door control Cool &...
GETTING TO KNOW YOUR VEHICLE door will cancel this feature. The time is To stop the window from going all the way down programmable. Refer to “Uconnect Settings” in during the Auto-Down operation, pull up on the “Multimedia” for further information. switch briefly.
GETTING TO KNOW YOUR VEHICLE Vent Open positions. This is a normal occurrence and can WARNING! (Continued) be minimized. If the buffeting occurs with the Push and release the Vent switch within one rear windows open, then open the front and In a collision, there is a greater risk of being ...
GETTING TO KNOW YOUR VEHICLE Sunroof Maintenance 3. Push the safety catch to the left. Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation NOTE: The power sunroof switch can remain active ...
GETTING TO KNOW YOUR VEHICLE With the ignition in the OFF position, the trunk Key Fob Trunk Release Button CAUTION! open symbol will display until the trunk is Push the power trunk button on the To prevent possible damage, do not slam the closed.
GETTING TO KNOW YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED Closing With one or more hands placed on the outside HomeLink® replaces up to three hand-held trunk surface push the trunk lid down until you transmitters that operate devices such as hear the trunk lock latch into place.
GETTING TO KNOW YOUR VEHICLE Before You Begin Programming HomeLink® door openers can be identified by the “LEARN” 3. Push and hold the HomeLink® button you or “TRAIN” button located where the hanging want to program while you push and hold Be sure that your vehicle is parked outside of antenna is attached to the garage door opener.
GETTING TO KNOW YOUR VEHICLE 6. Return to the vehicle and push the Programming A Non-Rolling Code door/device should activate when the programmed HomeLink® button twice HomeLink® button is pressed. For programming garage door openers manu- (holding the button for two seconds each factured before 1995.
GETTING TO KNOW YOUR VEHICLE Canadian radio frequency laws require trans- or longer in rare cases. The garage door flash after 20 seconds. Do not release the mitter signals to time-out (or quit) after several may open and close while you are program- button.
GETTING TO KNOW YOUR VEHICLE Troubleshooting Tips 2. This device must accept any interference WARNING! (Continued) received, including interference that may If you are having trouble programming Home- cause undesired operation. Your motorized door or gate will open and Link®, here are some of the most common solu- close while you are programming the tions:...
GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT Control – If Equipped” in “Multimedia” for further information. If equipped with Apple Storage CarPlay® and Android Auto™, refer to the Uconnect Owner’s Manual Supplement. Glove Compartment The glove compartment is located on the passenger side of the instrument panel.
GETTING TO KNOW YOUR VEHICLE Cupholders phones, small electronics and other low WARNING! powered electrical accessories. The power The front cupholders are located in the center If containers of hot liquid are place in the outlets are labeled with either a “key” or a console and in the door panels.
Page 67
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: WARNING! (Continued) All accessories connected to these powered The front integrated center stack power outlets should be removed or turned off when Do not touch with wet hands. outlet can be changed from switched “igni- the vehicle is not in use to protect the battery Close the lid when not in use and while tion”...
Page 68
GETTING TO KNOW YOUR VEHICLE CAUTION! (Continued) CAUTION! (Continued) CAUTION! (Continued) Many accessories that can be plugged in Accessories that draw higher power (i.e., Power outlets are designed for accessory draw power from the vehicle's battery, even coolers, vacuum cleaners, lights, etc.), will plugs only.
GETTING TO KNOW YOUR INSTRUMENT PANEL Instrument Cluster Descriptions 5. Temperature Gauge CAUTION! The temperature gauge shows engine 1. Tachometer coolant temperature. Any reading within Driving with a hot engine cooling system Indicates the engine speed in revolutions the normal range indicates that the could damage your vehicle.
GETTING TO KNOW YOUR INSTRUMENT PANEL SRT Instrument Cluster Descriptions 5. Temperature Gauge CAUTION! The temperature gauge shows engine 1. Tachometer coolant temperature. Any reading within Driving with a hot engine cooling system Indicates the engine speed in revolutions ...
GETTING TO KNOW YOUR INSTRUMENT PANEL systems are working and give you warnings Diagnostics — If Equipped when they are not. The steering wheel mounted Speed Warning — If Equipped controls allow you to scroll through the main The system allows the driver to select informa- menus and submenus.
GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: For the Trip and Fuel Economy menus (and Vehicles Equipped With Keyless Enter-N-Go — Performance Timers) — If Equipped: Ignition Holding the up or down or left Use the steering wheel instrument cluster right arrow button will loop the user Information is reset by pushing and holding...
GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: a vehicle with automatic transmission is in release the right or left arrow button to If the indicator message illuminates when you manual shift mode. The PSI provides the driver scroll through the submenus items of “Vehicle start the vehicle, the oil change indicator with a visual indication within the instrument Info.”...
Page 78
GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Temp Battery Voltage Boost Pressure — If Equipped Displays the actual oil temperature. Displays the actual battery voltage. Displays the current boost pressure. Oil Pressure Storage Mode InterCooler (I/C) Temp — If Equipped ...
Page 79
GETTING TO KNOW YOUR INSTRUMENT PANEL Push and release the up or down arrow 1/4 Mile (400 meters) Timer Push the ADAPTIVE CRUISE CONTROL (ACC) button until the Performance menu is displayed ON/OFF button (located on the steering wheel) Best ...
Page 80
GETTING TO KNOW YOUR INSTRUMENT PANEL ACC Proximity Warning Hold the OK button to reset average fuel or left arrow button will allow you to scroll economy information. through the stored messages. ACC Unavailable Warning Trip Info Screen Setup The instrument cluster display will return to ...
Page 81
GETTING TO KNOW YOUR INSTRUMENT PANEL 2. Upper Right Trip B Distance Diagnostics — If Equipped This feature allows the driver to view engine and Compass Audio Information emission vehicle faults. Outside Temp (default) Digital Speed ...
GETTING TO KNOW YOUR INSTRUMENT PANEL Speed Warning — If Equipped toring of the electrical system and status of the If the Battery Charge Warning Light is on it may indicate a problem with the charging vehicle battery. Push and release the up or down arrow button system.
GETTING TO KNOW YOUR INSTRUMENT PANEL Turning on all possible vehicle electrical What to do when an electrical load reduction tive trips and the evaluation of the vehicle loads (e.g. HVAC to max settings, exterior and action message is present (“Battery Saver On” and driving pattern did not help to identify the interior lights, overloaded power outlets cause.
Page 84
GETTING TO KNOW YOUR INSTRUMENT PANEL unbuckled, a chime will sound and the light will problem with the anti-lock brake system reser- NOTE: turn on. When driving, if the driver or front voir. The light may flash momentarily during sharp passenger seat belt remains unbuckled, the cornering maneuvers, which change fluid level If the light remains on when the parking brake...
Page 85
GETTING TO KNOW YOUR INSTRUMENT PANEL the parking brake is applied or a brake fault is If the light turns on while driving, safely pull over Do not operate the vehicle until the cause is detected. If the light does not illuminate, have and stop the vehicle.
GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: Door Open Warning Light WARNING! This light may turn on if the accelerator and This indicator will illuminate when a brake pedals are pressed at the same time. If you continue operating the vehicle when door is ajar/open and not fully closed.
Page 87
GETTING TO KNOW YOUR INSTRUMENT PANEL the bulb does not come on when turning the The “ESC OFF Indicator Light” and the “ESC CAUTION! ignition switch from OFF to ON/RUN, have the Indicator Light” come on momentarily each time the ignition is placed in the ON/RUN or condition checked promptly.
Page 88
GETTING TO KNOW YOUR INSTRUMENT PANEL Low Washer Fluid Warning Light — If sure. Driving on a significantly under-inflated CAUTION! Equipped tire causes the tire to overheat and can lead to Do not continue driving with one or more flat tire failure.
Page 89
GETTING TO KNOW YOUR INSTRUMENT PANEL telltale after replacing one or more tires or placed in the ON/RUN or ACC/ON/RUN position Loose Fuel Filler Cap Warning Light — If wheels on your vehicle to ensure that the and may stay on for as long as four seconds. Equipped replacement or alternate tires and wheels allow If the ABS light remains on or turns on while...
GETTING TO KNOW YOUR INSTRUMENT PANEL Yellow Indicator Lights ECO Mode Indicator Light — If Equipped Adaptive Cruise Control (ACC) Set With Target Vehicle Light — If Equipped This light will turn on when ECO Mode Forward Collision Warning OFF Indicator is active.
GETTING TO KNOW YOUR INSTRUMENT PANEL exceeded, a single chime will sound along with Sport Mode Indicator Light Blue Indicator Lights pop up message of Speed Warning Exceeded. This light will turn on when Sport High Beam Indicator Light When the set speed is exceeded, the indicator Mode is active.
GETTING TO KNOW YOUR INSTRUMENT PANEL technician in making repairs. Although your sions control system. Failure to pass could WARNING! vehicle will usually be drivable and not need prevent vehicle registration. towing, see an authorized dealer for service as ONLY an authorized service technician ...
Page 93
GETTING TO KNOW YOUR INSTRUMENT PANEL 2. As soon as you cycle the ignition switch to The MIL will not flash at all and will Regardless of whether your vehicle's OBD II the ON position, you will see the “Malfunc- remain fully illuminated until you place system is ready or not, if the MIL is illuminated tion Indicator Light (MIL)”...
SAFETY SAFETY FEATURES Brake pedal pulsations WARNING! (Continued) A slight drop of the brake pedal at the end of Anti-Lock Brake System (ABS) The ABS cannot prevent the natural laws of the stop physics from acting on the vehicle, nor can The Anti-Lock Brake System (ABS) provides it increase braking or steering efficiency These are all normal characteristics of ABS.
SAFETY Anti-Lock Brake Warning Light gation (ERM). These systems work together to WARNING! enhance both vehicle stability and control in The yellow “Anti-Lock Brake Warning Light” will various driving conditions. The Brake Assist System (BAS) cannot turn on when the ignition is placed in the ON/ prevent the natural laws of physics from Your vehicle may also be equipped with Ready RUN mode and may stay on for as long as four...
Page 96
SAFETY Electronic Brake Force Distribution (EBD) NOTE: or understeer condition. Engine power may also ERM is disabled anytime the ESC is in “Full Off” be reduced to help the vehicle maintain the The Electronic Brake Force Distribution (EBD) mode (if equipped). Refer to “Electronic Stability desired path.
Page 97
SAFETY for most driving conditions. Alternate ESC WARNING! WARNING! (Continued) modes should only be used for specific reasons Electronic Stability Control (ESC) cannot as noted in the following paragraphs. Vehicle modifications, or failure to properly prevent the natural laws of physics from maintain your vehicle, may change the Partial Off acting on the vehicle, nor can it increase...
Page 98
SAFETY NOTE: cluster remains illuminated. When it is pushed Full Off – If Equipped a third time the ESC will go back into ESC On, no This mode is intended for off-highway or For vehicles with multiple partial ESC modes ...
Page 99
SAFETY dealer as soon as possible to have the problem The “ESC OFF Indicator Light” indi- WARNING! (Continued) diagnosed and corrected. cates the customer has elected to have the Electronic Stability Control The Electronic Stability Control (ESC) The “ESC Activation/Malfunction Indicator cannot prevent the natural laws of physics (ESC) in a reduced mode.
Page 100
SAFETY The gear selection must match vehicle uphill Towing With HSA Disabling And Enabling HSA direction (i.e., vehicle facing uphill is in HSA will also provide assistance to mitigate roll This feature can be turned on or turned off. To forward gear;...
SAFETY 7. Rotate the steering wheel back to center toring how fast the throttle is released by the vehicles (automobiles, trucks, motorcycles, and then an additional slightly more than driver. The Electronic Brake Controller (EBC) will etc.) that enter the blind spot zones from the one-half turn to the right.
Page 102
SAFETY Manual Transmission Vehicles NOTE: The BSM system sensors operate when the The BSM system DOES NOT alert the driver vehicle is in any gear. about rapidly approaching vehicles that are outside the detection zones. The BSM system detection zone DOES NOT ...
Page 103
SAFETY Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle. Rear Monitoring Overtaking/Approaching Overtaking Traffic The BSM system is designed not to issue an alert on stationary objects such as guardrails, If you pass another vehicle slowly (with a rela- posts, walls, foliage, berms, etc.
Page 104
SAFETY The BSM system will not alert you of objects that WARNING! are traveling in the opposite direction of the vehicle in adjacent lanes. The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones.
Page 105
SAFETY detected object is present. Whenever an NOTE: WARNING! audible alert is requested, the radio volume is The BSM system will store the current operating Rear Cross Path Detection (RCP) is not a back reduced so that the alert can be better heard. mode when the vehicle is shut off.
SAFETY Le présent appareil est conforme aux CNR Forward Collision Warning (FCW) Operation - When the system determines a collision with d`Innovation, Science and Economic Develop- If Equipped the vehicle in front of you is no longer probable, ment applicables aux appareils radio exempts the warning message will be deactivated.
Page 107
SAFETY Turning FCW On Or Off Changing FCW Status oncoming traffic, or leading vehicles with the same or higher rate of speed. The FCW Sensitivity settings are programmable NOTE: through the Uconnect System. Refer to FCW will be disabled like ACC, with the The default status of FCW is on;...
SAFETY 2. This device must accept any interference ance could void the user’s authority to operate temperature effects and natural pressure loss received, including interference that may the equipment. through the tire. cause undesired operation. The TPMS will continue to warn the driver of low Tire Pressure Monitoring System (TPMS) tire pressure as long as the condition exists, Le présent appareil est conforme aux CNR...
Page 109
SAFETY decrease the tire pressure to approximately The TPMS is not a substitute for proper tire CAUTION! (Continued) 23 psi (158 kPa). This tire pressure is suffi- maintenance, and it is the driver’s responsi- bility to maintain correct tire pressure using ciently low enough to turn on the TPMS Warning Using aftermarket tire sealants may cause ...
Page 110
SAFETY Various Tire Pressure Monitoring System Should this occur, you should stop as soon as messages, which display in the instrument possible and inflate the tires with a low pressure cluster condition (those shown in a different color in the instrument cluster graphic) to the vehicle’s Tire Pressure Monitoring System Warning ...
Page 111
SAFETY If the ignition switch is cycled, this sequence will has a pressure below the low-pressure addition, the TPMS Warning Light will turn repeat, providing the system fault still exists. If warning limit, upon the next ignition key off and the graphic in the instrument cluster the system fault no longer exists, the TPMS cycle, the TPMS Warning Light will remain will display a new pressure value instead of...
SAFETY Beginning with the next ignition cycle, the TPMS 1. This device may not cause harmful interfer- NOTE: will no longer chime or display the “Service Tire ence, and Changes or modifications not expressly Pressure System” message in the instrument approved by the party responsible for compli- 2.
SAFETY Here are some simple steps you can take to mini- 6. All occupants should always wear their lap WARNING! (Continued) mize the risk of harm from a deploying air bag: and shoulder belts properly. Never install a rear-facing child restraint in ...
Page 114
SAFETY Vehicles Without Passenger Seating WARNING! (Continued) WARNING! (Continued) Installed It is dangerous to ride in a cargo area, Head restraints should never be adjusted If your vehicle does not have a factory installed inside or outside of a vehicle. In a collision, while the vehicle is in motion.
Page 115
SAFETY driver or outboard front seat passenger (if WARNING! (Continued) WARNING! (Continued) equipped with outboard front passenger seat BeltAlert) is unbuckled when the ignition switch If this vehicle was not factory equipped with All occupants, including the driver, should ...
Page 116
SAFETY Change of Status Lap/Shoulder Belts WARNING! (Continued) If the driver or outboard front seat passenger (if All seating positions in your vehicle are It is dangerous to ride in a cargo area, equipped with outboard front passenger seat equipped with lap/shoulder belts.
Page 117
SAFETY WARNING! (Continued) WARNING! (Continued) WARNING! (Continued) Two people should never be belted into a A seat belt that is buckled into the wrong A shoulder belt placed behind you will not single seat belt. People belted together can buckle will not protect you properly.
Page 118
SAFETY Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat).
Page 119
SAFETY Lap/Shoulder Belt Untwisting Procedure Extender. The Seat Belt Extender should be Seat Belts And Pregnant Women used only if the existing seat belt is not long Use the following procedure to untwist a twisted enough. When the Seat Belt Extender is not lap/shoulder belt.
Page 120
SAFETY Seat Belt Pretensioner Switchable Automatic Locking Retractors (ALR) The front outboard seat belt system is equipped with pretensioning devices that are designed to The seat belts in the passenger seating posi- remove slack from the seat belt in the event of tions are equipped with a Switchable Automatic a collision.
Page 121
SAFETY If the passenger seating position is equipped How To Disengage The Automatic Locking Mode WARNING! with an ALR and is being used for normal usage, Unbuckle the combination lap/shoulder belt only pull the seat belt webbing out far enough to Never place a rear-facing child restraint in ...
SAFETY Supplemental Restraint Systems (SRS) Driver and Front Passenger Air Bags is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not All passenger occupants within the vehicle must Seat Belt Buckle Switch ...
Page 123
SAFETY The Air Bag Warning Light does not come on Redundant Air Bag Warning Light ment. The words “SRS AIRBAG” or “AIRBAG” are during the four to eight seconds when the embossed on the air bag covers. If a fault with the Air Bag Warning ignition switch is first in the ON/RUN position.
Page 124
SAFETY collisions. A higher energy output is used for WARNING! (Continued) WARNING! (Continued) more severe collisions. Never place a rear-facing child restraint in Relying on the air bags alone could lead to This vehicle may be equipped with a driver and/ ...
Page 125
SAFETY Seat belts are necessary for your protection in WARNING! (Continued) all collisions, and also are needed to help keep you in position, away from an inflating air bag. Do not mount any accessories to the knee impact bolsters such as alarm lights, When the ORC detects a collision requiring the stereos, citizen band radios, etc.
Page 126
SAFETY Supplemental Side Air Bag Inflatable Curtains the window. The SABICs inflate with enough Side Impacts (SABICs) force to injure occupants if they are not belted The Side Air Bags are designed to activate in and seated properly, or if items are positioned This vehicle is equipped with Supplemental certain side impacts.
Page 127
SAFETY Side Air Bags are a supplement to the seat belt not a good indicator of whether or not Side Air WARNING! restraint system. Side Air Bags deploy in less Bags and seat belt pretensioners should have time than it takes to blink your eyes. Side Air Bags need room to inflate.
Page 128
SAFETY Instrument Panel If A Deployment Occurs For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If The front air bags are designed to deflate imme- Knee Impact Bolsters these particles settle on your clothing, follow diately after deployment.
Page 129
SAFETY Enhanced Accident Response System Cut off battery power to the: Enhanced Accident Response System Reset Procedure In the event of an impact, if the communication Engine network remains intact, and the power remains In order to reset the Enhanced Accident Electric Motor (if equipped) ...
SAFETY understanding how a vehicle’s systems To read data recorded by an EDR, special equip- WARNING! (Continued) performed. The EDR is designed to record data ment is required, and access to the vehicle or related to vehicle dynamics and safety systems the EDR is needed.
Page 131
SAFETY There are different sizes and types of restraints make sure that you can install it in the vehicle WARNING! for children from newborn size to the child where you will use it. In a collision, an unrestrained child can almost large enough for an adult safety belt.
Page 132
SAFETY Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who have outgrown their forward-facing Belt Positioning Booster Seat and the vehicle Larger Children child restraint, but are too small to properly fit seat belt, seated in a rear seat of the vehicle the vehicle’s seat belt Children 12 years old or younger, who have Vehicle Seat Belt, seated in a rear seat of the...
Page 133
SAFETY Older Children And Child Restraints All children whose weight or height is above the WARNING! (Continued) forward-facing limit for the child seat should use NOTE: a belt-positioning booster seat until the When your child restraint is not in use, ...
Page 134
SAFETY 1. Can the child sit all the way back against A child’s squirming or slouching can move the WARNING! the back of the vehicle seat? belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the If the rear or front passenger seats are not 2.
Page 135
SAFETY Use Any Attachment Method Shown With An “X” Below Combined Weight of LATCH – Lower Restraint Type the Child + Child LATCH – Lower Seat Belt + Top Seat Belt Only Anchors + Top Restraint Anchors Only Tether Anchor Tether Anchor Rear-Facing Child More than 65 lbs...
Page 136
SAFETY Vehicles Without Rear Seating Installed If your vehicle is not equipped with a rear passenger seat, your vehicle is not equipped with LATCH anchorages. If your vehicle is not equipped with a rear seat, FCA US LLC recom- mends that you do not allow children 12 years old and under to ride in your vehicle.
Page 137
SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage system until the combined What is the weight limit (child’s weight + weight of the weight of the child and the child restraint is 65 lbs child restraint) for using the LATCH anchorage system 65 lbs (29.5 kg) (29.5 kg).
Page 138
SAFETY Locating The LATCH Anchorages LATCH-compatible child restraint systems will WARNING! be equipped with a rigid bar or a flexible strap WARNING! If the rear or front passenger seats are not on each side. Each will have a hook or present in your vehicle, NEVER install a child connector to attach to the lower anchorage and If the rear or front passenger seats are not...
Page 139
SAFETY Always follow the directions of the child move it to its rear-most position to make How To Stow An Unused Switchable-ALR restraint manufacturer when installing your room for the child seat. You may also move (ALR) Seat Belt: child restraint. Not all child restraint systems the front seat forward to allow more room When using the LATCH attaching system to for the child seat.
Page 140
SAFETY the lap portion of the seat belt tight around the WARNING! WARNING! (Continued) child restraint so that it is not necessary to use Never place a rear-facing child restraint in a locking clip. The ALR retractor can be Child restraint anchorages are designed to ...
Page 141
SAFETY Vehicle With Rear Seating Rear Seat Delete — Only Front Passenger Seat Passenger Seat Delete — No Automatic Locking Re- Available tractor (ALR) Locations ALR — Switchable Automatic Locking Retractor ALR — Switchable Automatic Locking Retractor Top Tether Anchorage Symbol Top Tether Anchorage Symbol Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + weight of the...
Page 142
SAFETY Installing A Child Restraint With A Switchable child seat. You may also move the front restraint while you push the child restraint Automatic Locking Retractor (ALR): seat forward to allow more room for the rearward and downward into the vehicle child seat.
Page 143
SAFETY 2. Rotate or lift the cover to access the anchor 4. Attach the tether strap hook of the child WARNING! directly behind the seat where you are restraint to the top tether anchorage as placing the child restraint. Do not attach a tether strap for a rear-facing shown in the diagram.
SAFETY child restraint in the front passenger seat, then WARNING! (Continued) WARNING! (Continued) you must use the seat belt system to secure the restraint. A top tether strap extension may be It is extremely dangerous to ride in a cargo If you are required to drive with the trunk/ ...
SAFETY Safety Checks You Should Make Inside The intermittently or remains on while driving, have WARNING! an authorized dealer service the vehicle imme- Vehicle diately. An improperly attached, damaged, folded, or Seat Belts stacked floor mat, or damaged floor mat Refer to “Occupant Restraint Systems”...
SAFETY Lights WARNING! (Continued) WARNING! (Continued) Have someone observe the operation of brake ONLY use the driver’s side floor mat on the If the vehicle carpet has been removed and lights and exterior lights while you work the driver’s side floor area.
Page 147
SAFETY WARNING! WARNING! (Continued) WARNING! (Continued) To prevent SERIOUS INJURY or DEATH: The intended use of “Track-Use” parts is for In a collision, you and your passengers can race vehicles on race tracks. To help suffer much greater injuries if you are not ALWAYS remove any “Track-Use”...
STARTING AND OPERATING STARTING THE ENGINE WARNING! (Continued) CAUTION! (Continued) Before starting your vehicle, adjust your seat, Do not leave children or animals inside Do not shift between PARK, REVERSE, adjust the inside and outside mirrors, fasten parked vehicles in hot weather. Interior NEUTRAL, or DRIVE when the engine is your seat belt, and if present, instruct all other heat build-up may cause serious injury or...
STARTING AND OPERATING Normal Starting 2. Press and hold the brake pedal while NOTE: pushing the ENGINE START/STOP button To Turn On The Engine Using The ENGINE If the ignition switch is left in the ACC posi- once. tion, the system will automatically time out START/STOP Button —...
Page 150
STARTING AND OPERATING 3. If the gear selector is not in PARK, the The conditions under which AutoPark will Vehicle speed is 1.2 mph (1.9 km/h) or less ENGINE START/STOP button must be held engage are outlined on the following pages. Ignition switched from RUN to ACC ...
STARTING AND OPERATING NOTE: As an added precaution, always apply the WARNING! (Continued) In some cases the ParkSense graphic will be parking brake when exiting the vehicle. displayed in the instrument cluster. In these Do not attempt to push or tow your vehicle ...
STARTING AND OPERATING ENGINE BREAK-IN RECOMMENDATIONS — After Starting NOTE: A new engine may consume some oil during its The idle speed is controlled automatically, and 3.6L & 5.7L first few thousand miles (kilometers) of opera- it will decrease as the engine warms up. tion.
STARTING AND OPERATING 0 to 100 miles (0 to 161 km): Do not perform sustained operation with the NOTE: accelerator pedal at wide open throttle. Do not allow the engine to operate at idle for When the parking brake is applied and the ...
Page 154
STARTING AND OPERATING WARNING! WARNING! (Continued) Never use the PARK position as a substi- Do not leave the key fob in or near the tute for the parking brake. Always apply the vehicle or in a location accessible to chil- parking brake fully when parked to guard dren, and do not leave the ignition of a against vehicle movement and possible...
STARTING AND OPERATING MANUAL TRANSMISSION — IF EQUIPPED or clutch may occur if you do not fully press the CAUTION! (Continued) clutch pedal and lift off of the accelerator pedal Six-Speed Manual Transmission when shifting. Do not attempt to shift the transmission if ...
STARTING AND OPERATING You must always use FIRST gear (or REVERSE) Recommended Shift Speeds CAUTION! when starting from a standing position. To utilize your manual transmission efficiently Always make sure the vehicle comes to a for fuel economy, it should be upshifted as complete stop before shifting into REVERSE.
STARTING AND OPERATING AUTOMATIC TRANSMISSION — IF mission is warm. This is a normal condition Downshifting and is not an indication of a problem with To maintain a safe speed and prolong brake life, EQUIPPED your clutch or transmission. downshift to maintain a safe speed when descending a steep grade.
STARTING AND OPERATING NOTE: WARNING! (Continued) WARNING! (Continued) You must press and hold the brake pedal while shifting out of PARK. It is dangerous to shift out of PARK or Never leave children alone in a vehicle, or NEUTRAL if the engine speed is higher than with access to an unlocked vehicle.
STARTING AND OPERATING pedal must also be pressed to shift from The transmission gear selector provides PARK, NEUTRAL into DRIVE or REVERSE when the REVERSE, NEUTRAL, DRIVE, and MANUAL vehicle is stopped or moving at low speeds. (AutoStick) shift positions. Manual shifts can be made using the AutoStick shift control.
Page 160
STARTING AND OPERATING Gear Ranges When exiting the vehicle, always: WARNING! (Continued) Apply the parking brake. Do not depress the accelerator pedal when The transmission may not engage PARK if shifting from PARK or NEUTRAL into another Shift the transmission into PARK. ...
Page 161
STARTING AND OPERATING Look at the transmission gear position WARNING! (Continued) WARNING! (Continued) display and verify that it indicates the PARK position (P), and is not blinking. Unintended movement of a vehicle could Do not leave the key fob in or near the ...
Page 162
STARTING AND OPERATING improve performance and extend transmission operate only in certain gears, or may not shift at CAUTION! life by reducing excessive shifting and heat all. Vehicle performance may be severely Towing the vehicle, coasting, or driving for any buildup.
Page 163
STARTING AND OPERATING 5. Restart the engine. Operation NOTE: When the gear selector is in the DRIVE (D) position, 6. Shift into the desired gear range. If the Tapping one of the steering wheel-mounted the transmission will operate automatically, problem is no longer detected, the trans- shift paddles (+/-), if equipped, while the gear shifting between the eight available gears.
Page 164
STARTING AND OPERATING remain in the selected gear until another downshifts be obtained if the accelerator Transmission shifting will be more noticeable pedal is pressed to the floor. when AutoStick is enabled. upshift or downshift is chosen, except as described below.
STARTING AND OPERATING SPORT MODE — WITHOUT PERFORMANCE FUEL SAVER TECHNOLOGY 5.7L AND 6.4L WARNING! CONTROL ONLY — IF EQUIPPED Continued operation with reduced assist could pose a safety risk to yourself and Your vehicle is equipped with a SPORT Mode This feature offers improved fuel economy by others.
STARTING AND OPERATING NOTE: in the instrument cluster display to indicate the Speed Control is on. To turn the system off, Even if the power steering assistance is no push the on/off button a second time. “CRUISE longer operational, it is still possible to steer CONTROL OFF”...
STARTING AND OPERATING To Vary The Speed Setting If the button is continually pushed, the set quent tap of the button results in a decrease speed will continue to increase until the of 1 km/h. To Increase Speed button is released, then the new set speed If the button is continually pushed, the set When the Speed Control is set, you can increase ...
STARTING AND OPERATING Engine overspeed occurs NOTE: WARNING! Clutch pedal is pressed (manual transmis- If the sensor does not detect a vehicle ahead Speed Control can be dangerous where the sion only) of you, ACC will maintain a fixed set speed. system cannot maintain a constant speed.
Page 169
STARTING AND OPERATING You can change the mode by using the Cruise WARNING! (Continued) WARNING! (Continued) Control buttons. The two control modes func- tion differently. Always confirm which mode is The ACC system: You should switch off the ACC system: ...
STARTING AND OPERATING Adaptive Cruise Control (ACC) Operation of the Adaptive Cruise Control and Forward When the brakes are overheated. Collision Warning system. The Speed Control buttons (located on the right When the Electronic Stability Control (ESC) is side of the steering wheel) operate the Adaptive Activating Adaptive Cruise Control (ACC) in Full Off mode.
STARTING AND OPERATING Remove your foot from the accelerator pedal. If The vehicle parking brake is applied. you do not, the vehicle may continue to accel- The driver switches ESC to Full Off mode. erate beyond the set speed. If this occurs: To Turn Off The message “DRIVER OVERRIDE”...
STARTING AND OPERATING If the button is continually pushed, the set quent tap of the button results in a decrease WARNING! speed will continue to increase in 5 mph of 1 mph. The Resume function should only be used if increments until the button is released.
STARTING AND OPERATING The ACC system applies the brake down to 15 mph (24 km/h) when following a target vehicle. The ACC system maintains set speed when driving uphill and downhill. However, a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending downhill.
STARTING AND OPERATING To decrease the distance setting, push the NOTE: Overtake Aid Distance Setting — Decrease button and The brake lights will illuminate whenever the When driving with ACC engaged and following a release. Each time the button is pushed, the ACC system applies the brakes.
STARTING AND OPERATING Adaptive Cruise Control Set will indicate when conditions temporarily limit sensor is located in the center of the vehicle system performance. behind the lower grille. When the SET (+) or the SET (-) button (located on the steering wheel) is pushed, the display will This most often occurs at times of poor visibility, To keep the ACC System operating properly, it is read “ACC SET.”...
STARTING AND OPERATING NOTE: Precautions While Driving With ACC Turns And Bends When driving on a curve with ACC engaged, the In certain driving situations, ACC may have If the “ACC/FCW Unavailable Wipe Front system may decrease the vehicle speed and detection issues.
Page 177
STARTING AND OPERATING Using ACC On Hills Lane Changing Narrow Vehicles When driving on hills, ACC may not detect a ACC may not detect a vehicle until it is Some narrow vehicles traveling near the outer vehicle in your lane. Depending on the speed, completely in the lane in which you are trav- edges of the lane or edging into the lane are not vehicle load, traffic conditions, and the steep-...
STARTING AND OPERATING Stationary Objects And Vehicles 1. This device may not cause harmful interfer- NOTE: ence, and Changes or modifications not expressly ACC does not react to stationary objects and approved by the party responsible for compli- stationary vehicles. For example, ACC will not 2.
Page 179
STARTING AND OPERATING To Vary The Speed Setting If the button is continually pushed, the set WARNING! speed will continue to increase in 10 km/h To Increase Speed increments until the button is released. The In the Normal (Fixed Speed) Cruise Control When the Normal (Fixed Speed) Cruise Control increase in set speed is reflected in the mode, the system will not react to vehicles...
STARTING AND OPERATING Metric Speed (km/h) To Resume Speed cycle when the ignition is changed to the ON/ RUN position. Pushing the SET (-) button once will result in To resume a previously set speed, push the RES a 1 km/h decrease in set speed. Each subse- ParkSense can be active only when the gear button and release.
STARTING AND OPERATING The ParkSense Warning screen is located within display will show the single arc moving closer to the instrument cluster display. It provides visual the vehicle and the sound tone will change from warnings to indicate the distance between the fast to continuous.
STARTING AND OPERATING Service The ParkSense Rear Park Assist If “PARKSENSE UNAVAILABLE SERVICE When you turn ParkSense off in DRIVE, the instrument cluster will display "PARKSENSE REQUIRED” appears in the instrument cluster System OFF" for five seconds. Furthermore, once you display, see an authorized dealer.
STARTING AND OPERATING Ensure the ParkSense system is off if objects NOTE: CAUTION! such as bicycle carriers, trailer hitches, etc., The ParkView Rear Back Up Camera has are placed within 12 inches (30 cm) from the ParkSense is only a parking aid and it is programmable modes of operation that may be ...
STARTING AND OPERATING If the vehicle speed remains below 8 mph NOTE: WARNING! (13 km/h), the rear view camera image will If snow, ice, mud, or any foreign substance continue to be displayed until the transmission Drivers must be careful when backing up builds up on the camera lens, clean the lens, is shifted into PARK, the vehicle’s ignition is even when using the ParkView Rear Back Up...
STARTING AND OPERATING NOTE: the problem continues, the message will appear CAUTION! (Continued) When removing the fuel filler cap, lay the cap the next time the vehicle is started. tether in the hook, located on the fuel filler door. A poorly fitting fuel filler cap may cause the ...
STARTING AND OPERATING Type of vehicle Overloading tribute the weight. Improper weight distribution can have an adverse effect on the way your The load carrying components (axle, springs, Month, Day, and Hour of manufacture (MDH) vehicle steers and handles and the way the tires, wheels, etc.) of your vehicle will provide brakes operate.
STARTING AND OPERATING Common Towing Definitions Gross Axle Weight Rating (GAWR) installed between the hitch receiver and the trailer tongue that typically provides adjustable The GAWR is the maximum capacity of the front The following trailer towing related definitions friction associated with the telescoping motion and rear axles.
STARTING AND OPERATING tion/hydraulic sway control also dampens sway Trailer Hitch Classification WARNING! caused by traffic and crosswinds and contrib- The following chart provides the industry stan- utes positively to tow vehicle and trailer An improperly adjusted Weight Distributing dard for the maximum trailer weight a given Hitch system may reduce handling, stability.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. 3.6L Automatic 12 sq ft (1.11 sq m) 1,000 lbs (454 kg) 100 lbs (45 kg) 5.7L Automatic 12 sq ft (1.11 sq m) 1,000 lbs (454 kg) 100 lbs (45 kg) Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING Towing Requirements CAUTION! WARNING! (Continued) To promote proper break-in of your new vehicle Do not tow a trailer at all during the first Vehicles with trailers should not be parked drivetrain components, the following guidelines 500 miles (805 km) the new vehicle is on a grade.
Page 192
STARTING AND OPERATING Check the trailer tires for proper tire inflation Towing Requirements — Trailer Lights And WARNING! pressures before trailer usage. Wiring Do not connect trailer brakes to your Whenever you pull a trailer, regardless of the Check for signs of tire wear or visible tire ...
STARTING AND OPERATING Automatic Transmission — If Equipped Select the DRIVE range when towing. The trans- mission controls include a drive strategy to avoid frequent shifting when towing. However, if frequent shifting does occur while in DRIVE, you can use the AutoStick shift control to manually select a lower gear.
STARTING AND OPERATING RECREATIONAL TOWING (BEHIND AutoStick WARNING! When using the AutoStick shift control, select MOTORHOME, ETC.) Rapid acceleration on slippery surfaces is the highest gear that allows for adequate dangerous. Unequal traction can cause performance and avoids frequent down- Recreational towing (with all four wheels on the sudden pulling of the rear wheels.
STARTING AND OPERATING Keep tires properly inflated. Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving Maintain sufficient distance between your Determine the condition of the road or the through shallow standing water, consider the vehicle and the vehicle in front of you to avoid path that is under water and if there are any following Warnings and Cautions before doing so.
IN CASE OF EMERGENCY HAZARD WARNING FLASHERS ASSIST AND SOS MIRROR — IF EQUIPPED WARNING! The Hazard Warning flashers switch is located ALWAYS obey traffic laws and pay attention to on the instrument panel, below the radio. the road. ALWAYS drive safely with your hands Push the switch to turn on the Hazard on the steering wheel.
Page 197
IN CASE OF EMERGENCY ASSIST Call cancellation button on the Device Screen. WARNING! Termination of the SOS Call will turn off the The ASSIST Button is used to automatically green LED light on the Rearview Mirror. ALWAYS obey traffic laws and pay attention to connect you to any one of the following support the road.
Page 198
IN CASE OF EMERGENCY in the vehicle. The vehicle’s SOS Call system SOS Call System Limitations WARNING! (Continued) will attempt to remain connected with the Vehicles sold in Mexico DO NOT have SOS Call SOS operator until the SOS operator termi- The SOS Call system is embedded into the ...
Page 199
IN CASE OF EMERGENCY LTE (voice/data) or 4G (data) network and/or NOTE: WARNING! (Continued) Global Positioning Satellite signals are Your vehicle may be transmitting data as unavailable or obstructed. The Occupant Restraint Control module authorized by the subscriber. turns on the air bag Warning Light on the Equipment malfunction at the SOS operator ...
IN CASE OF EMERGENCY General Information Le présent appareil est conforme aux CNR La operación de este equipo está sujeta a las d`Innovation, Science and Economic Develop- siguientes dos condiciones: The following regulatory statement applies to all ment applicables aux appareils radio exempts Radio Frequency (RF) devices equipped in this 1.
IN CASE OF EMERGENCY BULB REPLACEMENT Replacement Bulbs All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement. Interior Bulbs Bulb Name Bulb Number Rear Courtesy/Reading Lamps Rear Compartment (Trunk) Lamp Overhead Console Reading Lamps...
IN CASE OF EMERGENCY Exterior Bulbs Bulb Name Bulb Number Front Side Marker LED (Serviced At Authorized Dealer) Tail Lamp LED (Serviced At Authorized Dealer) Stop/Turn Lamp LED (Serviced At Authorized Dealer) Rear Side Marker LED (Serviced At Authorized Dealer) Backup Lamp LED (Serviced At Authorized Dealer) Center High Mount Stop Lamp (CHMSL)
Page 203
IN CASE OF EMERGENCY 3. Turn the bulb counterclockwise, and Low Beam Headlamp, High Beam Headlamp Front Park/Signature Lamp remove. — Models With High Intensity Discharge (HID) The Front Park/Signature function is part of the Headlamps — If Equipped headlamp assembly and use LED lamps that are not serviceable separately.
IN CASE OF EMERGENCY FUSES Center Tail/Backup Lamp General Information The Center Tail/Backup Lamp use LED lamps The fuses protect electrical systems against WARNING! that are not serviceable separately. The Center excessive current. Tail/Backup Lamp must be replaced as an When a device does not work, you must check When replacing a blown fuse, always use ...
IN CASE OF EMERGENCY Underhood Fuses CAUTION! The Front Power Distribution Center is located When installing the power distribution in the engine compartment. This module center cover, it is important to ensure the contains fuses and relays. Fuse cavity location cover is properly positioned and fully and descriptions are printed on the inside of the latched.
Page 206
IN CASE OF EMERGENCY Cavity Cartridge Fuse Mini-Fuse Description 50 Amp Red / 20 Amp Blue – Radiator Fan (6.2L Supercharged) / Police Ignition Run / ACC # 2 – 20 Amp Yellow All-Wheel Drive Module – If Equipped – 10 Amp Red Intrusion MOD (300) –...
IN CASE OF EMERGENCY Rear Interior Fuses CAUTION! There is also a power distribution center located When installing the power distribution in the trunk under the spare tire access panel. center cover, it is important to ensure the This center contains fuses and relays. Fuse cover is properly positioned and fully cavity location and descriptions are printed on latched.
Page 209
IN CASE OF EMERGENCY Cavity Cartridge Fuse Mini-Fuse Description 40 Amp Green – Exterior Lighting #2 30 Amp Pink – Interior Lighting 40 Amp Green – Power Locks 30 Amp Pink – Driver Door Control Module 30 Amp Pink – Passenger Door Control Module –...
Page 210
IN CASE OF EMERGENCY Cavity Cartridge Fuse Mini-Fuse Description – 15 Amp Blue HVAC Module/Cluster Ignition Switch/RF Hub Module/Steering Column Lock (300) – If – 15 Amp Blue Equipped/ Remote Start – If Equipped – 10 Amp Red Steering Column Module/Clock (300) –...
Page 211
IN CASE OF EMERGENCY Cavity Cartridge Fuse Mini-Fuse Description – 10 Amp Red Heated Cupholders/Rear Heated Seat Switches – If Equipped – 10 Amp Red HVAC Module/In Vehicle Temperature Sensor – – Fuse – Spare – – Fuse – Spare –...
IN CASE OF EMERGENCY JACKING AND TIRE CHANGING Jack Location/Spare Tire Stowage The jack and spare tire are both stowed under WARNING! an access cover in the trunk. Follow these steps to access the jack and spare tire. Do not attempt to change a tire on the side ...
IN CASE OF EMERGENCY 6. Remove the jack and lug wrench assembly 3. Apply the parking brake. NOTE: from under the spare tire. Turn the jack Passengers should not remain in the vehicle 4. Place the gear selector into PARK (auto- screw to the left to loosen the lug wrench, when the vehicle is being lifted or raised.
Page 214
IN CASE OF EMERGENCY instructions for front tire replacement and CAUTION! WARNING! (Continued) replace the front road wheel with the wheel Do not attempt to raise the vehicle by jacking removed from the rear of the vehicle. Do not get under the vehicle when it is on a ...
Page 215
IN CASE OF EMERGENCY 3. Before raising the vehicle, use the lug NOTE: wrench to loosen, but not remove, the lug If the vehicle is too low for jack placement, slide nuts on the wheel with the flat tire. Turn the the jack on its side and rotate it up into position.
Page 216
IN CASE OF EMERGENCY 5. Raise the vehicle just enough to remove the NOTE: WARNING! flat tire and install the spare tire. For vehicles so equipped, do not attempt to To avoid the risk of forcing the vehicle off the install a center cap or wheel cover on the WARNING! jack, do not tighten the wheel nuts fully until...
IN CASE OF EMERGENCY 11. Stow the jack, tools and flat tire. Make sure 4. Refer to “Wheel And Tire Torque Specifica- WARNING! the base of the jack faces the front of the tions” in “Technical Specifications” for vehicle before tightening down the fastener. A loose tire or jack thrown forward in a proper lug nut torque.
IN CASE OF EMERGENCY Tire Service Kit Storage Tire Service Kit Components And Operation Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the The Tire Service Kit is located in the trunk. following symbols to indicate the air or sealant mode.
IN CASE OF EMERGENCY Using The Deflation Button these components immediately at your orig- WARNING! inal equipment vehicle dealer. Push the Deflation Button (2) to Do not attempt to seal a tire on the side of reduce the air pressure in the tire if When the Tire Service Kit sealant is in a liquid ...
IN CASE OF EMERGENCY Sealing A Tire With Tire Service Kit (B) Setting Up To Use Tire Service Kit: WARNING! (Continued) (A) Whenever You Stop To Use Tire Service 1. Push in the Mode Select Knob (5) and turn A loose Tire Service Kit thrown forward in a ...
Page 221
IN CASE OF EMERGENCY (C) Injecting Tire Service Kit Sealant Into The the Sealant Mode position and not Air will decrease quickly from approximately Mode. Push the Power Button (4) to turn 70 psi (4.8 Bar) to the actual tire pressure Deflated Tire: On the Tire Service Kit.
Page 222
IN CASE OF EMERGENCY If the tire inflates to the recommended pressure (D) Drive Vehicle: 3. Uncoil the Air Pump Hose (7) (black in color) or is at least 26 psi (1.8 Bar) pressure within and screw the fitting at the end of hose (7) Immediately after injecting sealant and inflating 15 minutes: onto the valve stem.
IN CASE OF EMERGENCY 4. Have the tire inspected and repaired or 4. Clean any remaining sealant from the Tire Tire Service Kit Storage replaced at the earliest opportunity at an Service Kit housing. The Tire Service Kit is located in the trunk. authorized dealer or tire service center.
IN CASE OF EMERGENCY Tire Service Kit Components And Operation Using The Mode Select Knob And Hoses Using The Deflation Button Your Tire Service Kit is equipped with the Push the Deflation Button (9) to following symbols to indicate the air or sealant reduce the air pressure in the tire if mode.
Page 225
IN CASE OF EMERGENCY The Sealant Bottle (4) and Sealant Hose (3) intended to seal punctures less than WARNING! (Continued) are a one tire application use and need to be 1/4 inch (6 mm) diameter in the tread of your replaced after each use.
IN CASE OF EMERGENCY 3. Place the transmission in PARK (auto trans- (C) Injecting Tire Service Kit Sealant Into The WARNING! (Continued) mission) or in Gear (manual transmission) Deflated Tire: and place the ignition in the OFF position. Tire Service Kit Sealant solution contains ...
Page 227
IN CASE OF EMERGENCY the Sealant Mode position and not Air will decrease quickly from approximately If the tire inflates to the recommended pressure Mode. Push the Power Button (1) to turn 70 psi (4.8 Bar) to the actual tire pressure or is at least 26 psi (1.8 Bar) pressure within On the Tire Service Kit.
Page 228
IN CASE OF EMERGENCY (E) After Driving: NOTE: CAUTION! (Continued) If the tire becomes over-inflated, push the Pull over to a safe location. Refer to “(A) When- Deflation Button to reduce the tire pressure to Failure to reinstall the cap on the fitting at ...
IN CASE OF EMERGENCY JUMP STARTING (F) Sealant Bottle And Hose Replacement: Preparations For Jump Start The battery is stored under an access cover in 1. Uncoil the Sealant Hose (3) (clear in color). If your vehicle has a discharged battery, it can the trunk.
IN CASE OF EMERGENCY Jump Starting Procedure WARNING! WARNING! (Continued) WARNING! Do not connect the jumper cable to the Remove any metal jewelry such as rings, watch bands and bracelets that could negative (-) post of the discharged battery. Failure to follow this jump starting procedure make an inadvertent electrical contact.
IN CASE OF EMERGENCY Disconnecting The Jumper Cables You can also turn the temperature control to CAUTION! maximum heat, the mode control to floor and 1. Disconnect the negative (-) end of the the blower control to high. This allows the Accessories plugged into the vehicle power jumper cable from the remote negative (-) heater core to act as a supplement to the...
IN CASE OF EMERGENCY MANUAL PARK RELEASE — 8 – SPEED 6. Pull the tether strap to rotate the lever up and rearward until it locks in place in the TRANSMISSION vertical position. The vehicle is now out of PARK and can be moved. Release the WARNING! parking brake only when the vehicle is securely connected to a tow vehicle.
IN CASE OF EMERGENCY 3. Pull up gently on the tether strap to confirm NEUTRAL for more than two seconds, you must WARNING! that the lever is locked in its stowed posi- press the brake pedal to engage DRIVE or tion.
IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheels OFF The Ground RWD MODELS AWD MODELS If transmission is operable: Transmission in NEUTRAL Flat Tow NONE NOT ALLOWED...
IN CASE OF EMERGENCY EVENT DATA RECORDER (EDR) If the transmission is not operable, or the CAUTION! (Continued) vehicle must be towed faster than 30 mph This vehicle is equipped with an Event Data (48 km/h) or farther than 30 miles (48 km), The manufacturer does not recommend ...
SERVICING AND MAINTENANCE SCHEDULED SERVICING The “Oil Change Required” message will be Severe Duty All Models displayed in the instrument cluster and a single Change Engine Oil at 4,000 miles (6,500 km) or 3.6L And 5.7L Engines chime will sound, indicating that an oil change 350 hours of engine run time if the vehicle is is necessary.
Page 237
SERVICING AND MAINTENANCE Maintenance Plan — 3.6L And 5.7L Required Maintenance Intervals Refer to the maintenance chart for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: Change oil and filter Rotate the tires. ...
Page 238
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV/Universal joints. Inspect front suspension, tie rod ends, boot seals and replace if necessary. Inspect the rear axle fluid. Inspect the front axle fluid (All Wheel Drive Only).
Page 239
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Maintenance Replace engine air cleaner filter. Replace cabin/air conditioning filter. Replace spark plugs. Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 240
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Change the transfer case fluid; if using your vehicle for any of the following: police, taxi, fleet, off-road, or frequent trailer towing. (All Wheel Drive Only). Change the rear axle fluid and on models equipped with All Wheel Drive (AWD) change the front axle...
SERVICING AND MAINTENANCE needed for vehicles in severe operating condi- Under no circumstances should oil change WARNING! tions, such as dusty areas and very short trip intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. You can be badly injured working on or driving.
Page 242
SERVICING AND MAINTENANCE Check the fluid levels of the coolant reservoir, At Each Oil Change CAUTION! brake master cylinder, and power steering Change the engine oil filter. (6.2L only), and add as needed. Failure to perform the required maintenance Inspect the brake hoses and lines.
Page 243
SERVICING AND MAINTENANCE Miles: Or Months: 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Inspect front suspension, tie rod ends, and boot seals, for cracks or leaks and all parts for damage, wear,...
Page 244
SERVICING AND MAINTENANCE Miles: Or Months: 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Inspect the CV/ Universal joints. Inspect the exhaust system.
Page 245
SERVICING AND MAINTENANCE Miles: Or Months: 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet or...
Page 246
SERVICING AND MAINTENANCE Miles: Or Months: 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Replace the spark plugs — 6.4L Engine Flush and replace the engine coolant at 120 months if not done at 150,000...
SERVICING AND MAINTENANCE Checking Oil Level — 3.6L And 5.7L Engine Adding Washer Fluid CAUTION! To ensure proper engine lubrication, the engine The windshield washer fluid reservoir is located Overfilling or underfilling the crankcase will oil must be maintained at the correct level. in the front of the engine compartment.
SERVICING AND MAINTENANCE Maintenance-Free Battery Pressure Washing WARNING! (Continued) The vehicle is equipped with a mainte- CAUTION! Battery posts, terminals, and related acces- nance-free battery. You will never have to add sories contain lead and lead compounds. water, nor is periodic maintenance required. Cleaning the engine compartment with a high Wash hands after handling.
SERVICING AND MAINTENANCE uled maintenance. Refer to “Scheduled WARNING! CAUTION! Servicing” in this section for the proper mainte- You can be badly injured working on or nance intervals. Do not use chemical flushes in your engine oil around a motor vehicle. Only do service work as the chemicals can damage your engine.
Page 254
SERVICING AND MAINTENANCE for all operating temperatures. This engine oil The engine oil filler cap also shows the recom- Synthetic Engine Oils improves low temperature starting and vehicle mended engine oil viscosity for your engine. For You may use synthetic engine oils provided the fuel economy.
SERVICING AND MAINTENANCE Shaker Hood Air Filter Cleaning Shaker Hood Removal And Cleaning Materials Added To Engine Oil The manufacturer strongly recommends 1. Remove the four nuts with the Shaker tool 1. Remove the air filter from the intake and against the addition of any additives (other than set the filter clamp a side.
SERVICING AND MAINTENANCE Engine Air Cleaner Filter T/A Air Filter Maintenance — If Equipped NOTE: It may be necessary to repeat steps 1 and 2 if Clean Engine Air Filter Refer to the “Maintenance Plan” in this section the air filter is not completely clean. for the proper maintenance intervals.
Page 257
SERVICING AND MAINTENANCE the condenser fins and a performance test. Refrigerant Recovery And Recycling R-134a NOTE: Drive belt tension should also be checked at Use only manufacturer approved A/C system — If Equipped this time. PAG compressor oil, and refrigerants. R-134a Air Conditioning Refrigerant is a hydro- fluorocarbon (HFC) that is an ozone-friendly A/C Air Filter...
SERVICING AND MAINTENANCE 2. Unsnap both ends and lift the filter access 5. Close the filter access cover. normal. Any belt with cracks running along a rib cover. must be replaced. Also have the belt replaced if Refer to “Scheduled Servicing” in this section it has excessive wear, frayed cords or severe for the proper maintenance intervals.
SERVICING AND MAINTENANCE Belt broken (note: identify and correct performing other underhood services, the hood present with chattering, marks, water lines or problem before new belt is installed) latch, release mechanism and safety catch wet spots. If any of these conditions are should be cleaned and lubricated.
SERVICING AND MAINTENANCE 2. To disengage the wiper blade from the wiper 4. Slide the wiper blade up into the hook on arm, press the release tab on the wiper the wiper arm, latch engagement will be blade and while holding the wiper arm with accompanied by an audible click.
Page 261
SERVICING AND MAINTENANCE the engine and allow it to cool. Service, WARNING! CAUTION! (Continued) including a tune-up to manufacturer's specifica- Exhaust gases can injure or kill. They tions, should be obtained immediately. Damage to the catalytic converter can contain carbon monoxide (CO), which is result if your vehicle is not kept in proper To minimize the possibility of catalytic converter...
SERVICING AND MAINTENANCE Cooling System Check the front of the radiator for any accumu- filled. If any coolant is needed to be added to lation of bugs, leaves, etc. If dirty, clean by the system please contact an local authorized WARNING! gently spraying water from a garden hose verti- dealer.
Page 263
SERVICING AND MAINTENANCE Do not use water alone or alcohol-based coolant (OAT coolant conforming to MS.90032) NOTE: engine coolant (antifreeze) products. Do not throughout the life of your vehicle. It is the owner's responsibility to maintain the use additional rust inhibitors or antirust prod- Please review these recommendations for proper level of protection against freezing ucts, as they may not be compatible with the...
Page 264
SERVICING AND MAINTENANCE The cap should be inspected and cleaned if nity. To prevent ingestion by animals or chil- Points To Remember there is any accumulation of foreign material on dren, do not store ethylene glycol-based coolant NOTE: the sealing surfaces. in open containers or allow it to remain in When the vehicle is stopped after a few miles/ puddles on the ground.
SERVICING AND MAINTENANCE Maintain engine coolant (antifreeze) concen- However, low fluid level may be caused by a WARNING! tration at a minimum of 50% OAT coolant leak and a checkup may be needed. (conforming to MS.90032) and distilled Riding the brakes can lead to brake failure Use only brake fluid that has been recom- water for proper corrosion protection of your and possibly a collision.
SERVICING AND MAINTENANCE master cylinder reservoir. In the event of Refer to the “Maintenance Plan” in this section WARNING! (Continued) for the proper maintenance intervals. leakage or wear, use only the manufacturer's recommended brake fluid. Refer to “Fluids And To avoid contamination from foreign matter ...
SERVICING AND MAINTENANCE Special Additives improper fluid level can cause severe transmis- inspect the transfer case fluid level, remove the sion damage. fill/inspection plug. The fluid level should be The manufacturer strongly recommends even with the bottom of the hole. Use this plug against using any special additives in the trans- CAUTION! to add fluid as required.
SERVICING AND MAINTENANCE Change Axle Fluid Tire Markings European — Metric tire sizing is based on European design standards. Tires designed Refer to “Scheduled Servicing” in “Servicing to this standard have the tire size molded And Maintenance” for the proper maintenance into the sidewall beginning with the section intervals.
Page 269
SERVICING AND MAINTENANCE Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in)
Page 270
SERVICING AND MAINTENANCE EXAMPLE: H = Speed Symbol A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle ...
Page 271
SERVICING AND MAINTENANCE EXAMPLE: ABCD = Code used by the tire manufacturer (one to four digits) 03 = Number representing the week in which the tire was manufactured (two digits) 03 means the 3rd week 01 = Number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 ...
Page 272
SERVICING AND MAINTENANCE Tire Loading And Tire Pressure This placard tells you important information about the: NOTE: 1. Number of people that can be carried in The proper cold tire inflation pressure is listed the vehicle. on the driver’s side B-Pillar or the rear edge of the driver's side door.
Page 273
SERVICING AND MAINTENANCE (3) Subtract the combined weight of the NOTE: Metric Example For Load Limit Under a maximum loaded vehicle condition, driver and passengers from XXX kg or For example, if “XXX” amount equals 635 kg gross axle weight ratings (GAWRs) for the front and there will be five 68 kg passengers in your XXX lbs.
Page 274
SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
SERVICING AND MAINTENANCE Tires — General Information Fuel Economy WARNING! (Continued) Underinflated tires will increase tire rolling Tire Pressure Overinflated or underinflated tires can resistance resulting in higher fuel consumption. Proper tire inflation pressure is essential to the affect vehicle handling and can fail Tread Wear safe and satisfactory operation of your vehicle.
Page 276
SERVICING AND MAINTENANCE Example: If garage temperature = 68°F (20°C) CAUTION! WARNING! and the outside temperature = 32°F (0°C) then After inspecting or adjusting the tire pressure, the cold tire inflation pressure should be High speed driving with your vehicle under always reinstall the valve stem cap.
Page 277
SERVICING AND MAINTENANCE Tire Repair limited driving capabilities and needs to be WARNING! replaced immediately. A Run Flat tire is not If your tire becomes damaged, it may be repairable. When a run flat tire is changed after Fast spinning tires can be dangerous. Forces repaired if it meets the following criteria: driving with underinflated tire condition, please generated by excessive wheel speeds may...
Page 278
SERVICING AND MAINTENANCE These indicators are molded into the bottom of for the size designation of your tire. The Load WARNING! the tread grooves. They will appear as bands Index and Speed Symbol for your tire will be when the tread depth becomes a 1/16 of an Tires and the spare tire should be replaced found on the original equipment tire sidewall.
SERVICING AND MAINTENANCE For more information, contact an authorized WARNING! CAUTION! dealer. Do not use a tire, wheel size, load rating, or Replacing original tires with tires of a Summer tires do not contain the all season speed rating other than that specified for different size may result in false speedometer designation or mountain/snowflake symbol on your vehicle.
SERVICING AND MAINTENANCE Snow tires generally have lower speed ratings Refer to the “Towing Requirements - Tires” in and reinstalled on your vehicle at the first than what was originally equipped with your “Starting And Operating” for restrictions when opportunity. vehicle and should not be operated at towing with a spare tire designated for tempo- Do not install a wheel cover or attempt to mount...
SERVICING AND MAINTENANCE Collapsible spare tire description example: Full Size Spare — If Equipped WARNING! 165/80-17 101P. The full size spare is for temporary emergency Limited use spares are for emergency use Since this tire has limited tread life, the original use only.
SERVICING AND MAINTENANCE chemicals used to melt ice or control dust on Dark Vapor Chrome, Black Satin Chrome, or CAUTION! dirt roads. Use a soft cloth or sponge and mild Low Gloss Clear Coat Wheels soap to wipe away promptly. Do not use harsh Do not use scouring pads, steel wool, a bristle CAUTION! chemicals or a stiff brush.
SERVICING AND MAINTENANCE Rear Wheel Drive (RWD) Models Tire Chains And Traction Devices — SRT CAUTION! (Continued) For a 235/55R18 tire, use of a Peerless Chain Due to limited clearance, tire chains or traction Install device as tightly as possible and Super Z6 low profile traction device or equiva- ...
SERVICING AND MAINTENANCE The suggested rotation method is the “rearward Refer to “Scheduled Servicing” in “Servicing different size tires on the front and rear of the cross” shown in the following diagram. This And Maintenance” for the proper maintenance vehicle. rotation pattern does not apply to some direc- intervals.
SERVICING AND MAINTENANCE Standard No. 109. Grades B and A repre- Treadwear WARNING! sent higher levels of performance on the The Treadwear grade is a comparative The traction grade assigned to this tire is laboratory test wheel, than the minimum rating, based on the wear rate of the tire based on straight-ahead braking traction required by law.
SERVICING AND MAINTENANCE Disconnect the negative cable from the The following maintenance recommendations with a dry cloth. To remove road dirt, wash with battery. will enable you to obtain maximum benefit from a mild soap solution followed by rinsing. the corrosion resistance built into your vehicle.
SERVICING AND MAINTENANCE If you carry special cargo such as chemicals, Seat Belt Maintenance CAUTION! fertilizers, de-icer salt, etc., be sure that such Do not bleach, dye, or clean the belts with materials are well packaged and sealed. Do not use abrasive or strong cleaning ...
SERVICING AND MAINTENANCE Plastic And Coated Parts Leather Parts CAUTION! Use Mopar Total Clean to clean vinyl upholstery. Mopar Total Clean is specifically recommended Do not use Alcohol and Alcohol-based and/or for leather upholstery. Ketone based cleaning products to clean CAUTION! Your leather upholstery can be best preserved leather upholstery, as damage to the...
TECHNICAL SPECIFICATIONS IDENTIFICATION DATA BRAKE SYSTEM SRT — If Equipped NOTE: Your vehicle is equipped with dual hydraulic Vehicle Identification Number Your vehicle is equipped with a high perfor- brake systems. If either of the two hydraulic The Vehicle Identification Number (VIN) is on mance braking system.
TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS 5.7L Engine (With Automatic Transmission) 5.7L Engine (With Manual Transmission) Do not use E-85 flex fuel or ethanol blends Do not use E-85 flex fuel or ethanol blends 3.6L Engine greater than 15% in this engine. greater than 15% in this engine.
TECHNICAL SPECIFICATIONS 6.2L Supercharged Engine 6.4L Engine Reformulated Gasoline Do not use E-85 flex fuel or ethanol blends Do not use E-85 flex fuel or ethanol blends Many areas of the country require the use of greater than 15% in this engine. greater than 15% in this engine.
TECHNICAL SPECIFICATIONS www.toptiergas.com for a list of TOP TIER Deter- Problems that result from using gasoline CNG And LP Fuel System Modifications gent Gasoline Retailers. containing more than 15% ethanol (E-15) or Modifications that allow the engine to run on gasoline containing methanol are not the Indiscriminate use of fuel system cleaning Compressed Natural Gas (CNG) or Liquid...
TECHNICAL SPECIFICATIONS Fuel System Cautions Carbon Monoxide Warnings CAUTION! (Continued) CAUTION! WARNING! The use of fuel additives, which are now being sold as octane enhancers, is not Follow these guidelines to maintain your Carbon monoxide (CO) in exhaust gases is recommended.
TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS — NON-SRT Engine Component Fluid, Lubricant, or Genuine Part We recommend you use Mopar Antifreeze/Coolant 10 Year/ Engine Coolant 150,000 (240,000 km) Mile Formula OAT (Organic Additive Technology). We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as Mopar SAE Engine Oil –...
Page 298
TECHNICAL SPECIFICATIONS CAUTION! CAUTION! (Continued) CAUTION! (Continued) Mixing of engine coolant (antifreeze) other Do not use water alone or alcohol-based This vehicle has not been designed for use than specified Organic Additive Technology engine coolant (antifreeze) products. Do with propylene glycol-based engine coolant (OAT) engine coolant (antifreeze), may not use additional rust inhibitors or antirust...
TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Use only Mopar ZF 8&9 Speed ATF Automatic Transmission Fluid, or 8-Speed Automatic Transmission equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Manual Transmission – If Equipped We recommend you use Mopar ATF+4 Automatic Transmission Fluid.
TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS — SRT Engine Component Fluid, Lubricant, or Genuine Part Engine/Intercooler Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT coolant conforming to MS.90032. For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils.
Page 301
TECHNICAL SPECIFICATIONS CAUTION! CAUTION! (Continued) CAUTION! (Continued) Mixing of engine coolant (antifreeze) other Do not use water alone or alcohol-based This vehicle has not been designed for use than specified Organic Additive Technology engine coolant (antifreeze) products. Do with propylene glycol-based engine coolant (OAT) engine coolant (antifreeze), may not use additional rust inhibitors or antirust...
TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Manual Transmission – If Equipped We recommend you use Mopar ATF+4 Automatic Transmission Fluid. Use only Mopar ZF 8&9 Speed ATF Automatic Transmission Fluid, or Automatic Transmission – If Equipped equivalent. Failure to use the correct fluid may affect the function or performance of your transmission.
MULTIMEDIA UCONNECT SYSTEMS Your vehicle may be equipped with certain secu- WARNING! rity features to reduce the risk of unauthorized For detailed information about your Uconnect and unlawful access to vehicle systems and It is not possible to know or to predict all of ...
MULTIMEDIA UCONNECT SETTINGS NOTE: Customer Programmable Features — Uconnect 4 Settings FCA US LLC or your dealer may contact you The Uconnect system uses a combination of directly regarding software updates. buttons on the touchscreen and buttons on the faceplate located on the center of the instru- To help further improve vehicle security and ...
Page 305
MULTIMEDIA NOTE: check-mark appears next to the setting, toggle up or down through the available Depending on the vehicle’s options, feature showing that setting has been selected. Once settings. settings may vary. the setting is complete, press the X button on The following tables list the settings that may be the touchscreen to close out of the settings found within the Uconnect 4 with 7-inch display...
Page 306
MULTIMEDIA Setting Name Selectable Options Display Brightness With Headlights – NOTE: When in the “Display Brightness With Headlights OFF” display, you may select the brightness with the headlights off. Adjust the brightness from (1–10) with the + and – buttons on the touchscreen. To make changes to the "Display Brightness With Headlights OFF"...
Page 307
MULTIMEDIA Setting Name Selectable Options Navigation Turn-By-Turn Displayed In Cluster — If Equipped NOTE: When the “Navigation Turn-By-Turn Displayed In Cluster” feature is selected, the turn-by-turn directions will appear in the instrument cluster display as the vehicle approaches a designated turn within a programmed route. Units After pressing the Units button on the touchscreen you may select each unit of measurement independently displayed in the instrument cluster display.
Page 308
MULTIMEDIA Clock After pressing the Clock button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With GPS — If Equipped NOTE: The “Sync Time With GPS” feature will allow you to automatically have the radio set the time. Set Time Hours –...
Page 309
MULTIMEDIA Setting Name Selectable Options Active Parkview Backup Camera Guidelines NOTE: The “Active ParkView Backup Camera Guidelines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its projected backup path, based on the steering wheel position when the option is checked. A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.
Page 310
MULTIMEDIA Setting Name Selectable Options Electric Power Steering Default— If Sport Normal Comfort Equipped NOTE: When "Electric Power Steering Default" is selected, it allows you to change the default setting of your vehicle to either Normal, Sport, or Comfort. ParkSense — If Equipped Sound Only Sound and Display NOTE:...
Page 311
MULTIMEDIA Setting Name Selectable Options Blind Spot Alert — If Equipped Lights Lights and Chime NOTE: When this feature is selected, the Blind Spot Alert feature provides alerts, visual and/or audible, to indicate objects in your blind spot. The Blind ...
Page 312
MULTIMEDIA Setting Name Selectable Options Rain Sensing Auto Wipers NOTE: When this feature is selected and the wipers are on, the system will automatically activate the windshield wipers if it senses moisture on the wind- shield. Hill Start Assist — If Equipped NOTE: When this feature is selected, the Hill Start Assist (HSA) system is active.
Page 313
MULTIMEDIA Setting Name Selectable Options Steering Directed Lights Flash Lights With Lock Doors & Locks After pressing the Doors & Locks button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto Door Locks — If Equipped Auto Unlock On Exit Flash Lights With Lock NOTE:...
Page 314
MULTIMEDIA Setting Name Selectable Options Personal Settings Linked To Key Fob — If Equipped NOTE: This feature provides automatic recall of all settings stored to a memory location (driver’s seat, exterior mirrors, steering column position and radio station presets) to enhance driver mobility when entering and exiting the vehicle. The seat returns to the memorized seat location (if Personal Settings Linked to Key Fob is set to on) when the key fob is used to unlock the door.
Page 315
MULTIMEDIA Setting Name Selectable Options 0 sec 5 mins Engine Off Power Delay 45 sec 10 mins NOTE: When this feature is selected, the power window switches, radio, Uconnect phone system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets remain active for up to 10 minutes after the ignition is cycled to OFF.
Page 316
MULTIMEDIA Setting Name Selectable Options Surround Sound — If Equipped NOTE: The “Surround Sound” feature provides simulated surround sound mode. To make your selection, press the Surround Sound button on the touch- screen, and select On or Off. AUX Volume Offset — If –...
Page 317
MULTIMEDIA Setting Name Selectable Options Paired Phones/Devices List of Paired Phones/Devices NOTE: This feature shows which phones are paired to the Phone/Bluetooth® system. For further information, refer to “Phone Mode” in the “Uconnect 4 with 7-inch Display” section. SiriusXM® Setup — If Equipped After pressing the SiriusXM®...
Page 318
MULTIMEDIA Restore Settings After pressing the Restore Settings button on the touchscreen, the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When the “Restore Settings” feature is selected it will reset the Display, Clock, Audio, and Radio Settings to their default settings. If “Yes” is selected, a pop-up will appear asking "Are you sure you want to reset your settings to default?”...
MULTIMEDIA Customer Programmable Features — Press the Apps button, then press the When making a selection, press the button on Settings button on the touchscreen to the touchscreen to enter the desired mode. Uconnect 4C/4C NAV Settings display the menu setting screen. In this mode, Once in the desired mode, press and release the Uconnect system allows you to access the preferred setting “option”...
Page 320
MULTIMEDIA Language After pressing the Language button on the touchscreen, the following settings will be available: Setting Name Selectable Options Language English Français Español Display After pressing the Display button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Auto...
Page 321
MULTIMEDIA Setting Name Selectable Options Set Theme List Of Themes NOTE: When in the “Set Theme” display, you may select the theme for the display screen. To make your selection, press the Set Theme button on the touch- screen, then select the desired theme option button until a check-mark appears showing that the setting has been selected. AutoShow Smartphone Display Upon Connection —...
Page 322
MULTIMEDIA Units After pressing the Units button on the touchscreen, you may select each unit of measurement independently displayed in the instrument cluster display, and navigation system (if equipped). The following selectable units of measurement are listed below: Setting Name Selectable Options Units Metric...
Page 323
MULTIMEDIA Clock & Date After pressing the Clock & Date button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With GPS — If Equipped NOTE: The “Sync Time With GPS” feature will allow you to automatically have the radio set the time. Set Time Hours –...
Page 324
MULTIMEDIA Setting Name Selectable Options Active ParkView Backup Camera Guidelines NOTE: The “Active ParkView Backup Camera Guidelines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its projected backup path, based on the steering wheel position when the option is checked. A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.
Page 325
MULTIMEDIA Setting Name Selectable Options Electric Power Steering Default — If Sport Normal Comfort Equipped NOTE: When "Electric Power Steering Default" is selected, it allows you to change the default setting of your vehicle to either normal, sport, or comfort. ParkSense —...
Page 326
MULTIMEDIA Setting Name Selectable Options Hill Start Assist — If Equipped NOTE: When this feature is selected, the Hill Start Assist (HSA) system is active. Paddle Shifters Mirrors & Wipers After pressing the Mirror and Wipers button on the touchscreen, the following settings will be available: Setting Name Selectable Options Rain Sensing Auto Wipers...
Page 327
MULTIMEDIA Setting Name Selectable Options Auto Dim High Beams — If Equipped Daytime Running Lights — If Equipped NOTE: When the “Daytime Running Lights” feature is selected, the daytime running lights can be turned On or Off. This feature is only allowed by law in the country of the vehicle purchase.
Page 328
MULTIMEDIA Setting Name Selectable Options Sound Horn With Lock 1st Press 2nd Press Sound Horn With Remote Start — If Equipped 1st Press Of Key Fob Unlocks Driver Door All Doors NOTE: When "Driver Door" is programmed with 1st Press Of Key Fob Unlocks, only the driver's door unlocks with the first press of the key fob unlock button. ...
Page 329
MULTIMEDIA Auto-On Comfort Systems — If Equipped After pressing the Auto-On Comfort button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/Vented Seat Remote Start All Starts & Heated Steering Wheel NOTE: When this feature is selected the driver's heated seat and heated steering wheel will automatically turn on when temperatures are below 40°F (4.4°C).
Page 330
MULTIMEDIA Setting Name Selectable Options NOTE: When the “Headlight Off Delay” feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To change the Headlight Off Delay status press the + or – button on the touchscreen to select your desired time interval. Audio After pressing the Audio button on the touchscreen, the following settings will be available: Setting Name...
Page 331
MULTIMEDIA Setting Name Selectable Options Surround Sound — If Equipped NOTE: The “Surround Sound” feature provides simulated surround sound mode. To make your selection, press the Surround Sound button on the touch- screen, select “On” or “Off.” AUX Volume Offset — If Equipped NOTE: The “AUX Volume Offset”...
Page 332
MULTIMEDIA Setting Name Selectable Options Paired Phones and Audio Sources List Of Paired Phones and Audio Sources NOTE: The “Paired Phones and Audio Sources” feature shows which phones and audio sources are paired to the Phone and Audio Sources Settings system. For further information, refer to the Uconnect Owner’s Manual Supplement.
Page 333
MULTIMEDIA Setting Name Selectable Options Subscription Information Subscription Info NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM® Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe. 1.
Page 334
MULTIMEDIA Setting Name Selectable Options Clear Personal Data Cancel NOTE: When this feature is selected, it will remove all personal data including Bluetooth® devices and presets. To remove personal information, press the Clear Personal Data button and a pop-up will appear asking “Are you sure you want to clear all personal data?” Modem Reset Cancel System Information —...
MULTIMEDIA SAFETY AND GENERAL INFORMATION Stop use immediately if a problem occurs. NOTE: Failure to do so may cause injury or damage Many features of this system are speed depen- Safety Guidelines to the product. Return it to an authorized dent.
MULTIMEDIA Do not spray any liquid or caustic chemicals NOTE: 4. Apps directly on the screen! Use a clean and dry Uconnect screen images are for illustration Press the Apps button on the touchscreen microfiber lens cleaning cloth in order to purposes only and may not reflect exact soft- to access Smartphone and Connected vehi- clean the touchscreen.
MULTIMEDIA Drag & Drop Menu Bar NOTE: Tune/Scroll Control This feature is only available if the vehicle is in When the audio system is turned on, the sound The Uconnect features and services in the main PARK. will be set at the same volume level as last menu bar are easily changed for your conve- played.
Page 338
MULTIMEDIA Fast Seek Up be used to direct tune the radio to a desired for more than two seconds or until you hear a station or channel. confirmation beep. Press and hold the Seek Up button on the touchscreen to advance the radio through the Press the available number button on the The Radio stores up to 12 presets in each of the available stations or channels at a faster rate.
Page 340
MULTIMEDIA NOTE: Replay Forward You will need to provide the SiriusXM® ID (RID) Each press of the FW button on the touchscreen The replay function provides a means to store located at the bottom of the Channel 0 screen. forwards the content in steps of five seconds. and replay up to 22 minutes of music audio and Forwarding of the content can only be done 48 minutes of talk radio.
Page 341
MULTIMEDIA Fav. Artist: While the song is playing to set a Genre Favorites Favorite Artist, press the Fav button on the Press the Genre button on the touchscreen to Press the Favorites button located at the left of touchscreen and then the Fav. Artist button on display a list of Genres.
Page 342
MULTIMEDIA Game Zone Alert Settings Balance & Fade Press the Game Zone button, located at the left Press the Alert Setting tab at the top of the of the Browse screen. This feature provides you screen. The Alert Settings menu allows you to with the ability to select teams, edit the selec- choose from “Alert me to on-air games upon tion, and set alerts.
Page 343
MULTIMEDIA Equalizer Speed Adjusted Volume When Surround Sound is On, you can hear audio coming from every direction as in a movie theatre or home theatre system. Equalizer Speed Adjusted Volume Press the Equalizer button on the touchscreen Press the Speed Adjusted Volume button on the Surround Sound to activate the Equalizer screen.
MULTIMEDIA Press the On button on the touchscreen to acti- Auto Play Radio Off With Door vate Loudness. Press Off to deactivate this feature. When Loudness is On, the sound quality at lower volumes improves. AUX Volume Offset Auto Play Radio Off With Door Press the Auto Play button on the touchscreen Press the Radio Off With Door button on the...
Page 345
MULTIMEDIA Seek Up /Seek Down Repeat Tune/Scroll knob to highlight a track (indicated by the line above and below the track name) Press and release the Seek Up button on the Press the Repeat button on the touchscreen to and then push the Enter/Browse knob to start touchscreen for the next selection on the USB toggle the repeat functionality.
Page 346
MULTIMEDIA Controlling The Auxiliary Device Before proceeding, the Bluetooth® device must Bluetooth® device is within the first second of be paired to the Uconnect Phone to communi- the current selection. The control of the auxiliary device (e.g., cate with the Uconnect System. selecting playlists, play, fast forward, etc.) Media Mode cannot be provided by the radio;...
Page 347
MULTIMEDIA Android Auto™ is a feature of your Uconnect NOTE: Once Android Auto™ is up and running on your system, and your Android 5.0 Lollipop™ or Be sure to use the factory-provided USB cable Uconnect system, the following features can be higher powered smartphone with a data plan, that came with your phone, as aftermarket utilized using your smartphone’s data plan:...
Page 348
MULTIMEDIA NOTE: NOTE: Requires compatible smartphone running Music apps, playlists, and stations must be set Android™ 5.0 Lollipop or higher and download up on your smartphone prior to using Android app on Google Play. Android™, Android Auto™ Auto™, for them to work with Android Auto™. and Google Play are trademarks of Google Inc.
Page 349
MULTIMEDIA Android Auto™ Communication Android Auto™ Apps 1. Connect your iPhone® to one of the media USB ports in your vehicle. With Android Auto™ connected, press and hold The Android Auto™ App will display all the compatible apps that are available to use with the VR button on the steering wheel to activate NOTE: voice recognition specific to the Android Auto™.
Page 350
MULTIMEDIA Once Apple CarPlay® is up and running on your session. You can also press and hold the Home Apple CarPlay® Messages Uconnect system, the following features can be button within Apple CarPlay® to start talking to Just like Phone, Apple CarPlay® utilized using your iPhone’s®...
Page 351
MULTIMEDIA NOTE: NOTE: Multiple Devices Connecting To The Uconnect If the Voice Recognition (VR) button is not held, AutoPlay is not supported by Android Auto™. System and is only pushed, the built-in Uconnect VR It is possible to have multiple devices AutoShow prompts you and any navigation command said connected to the Uconnect system.
MULTIMEDIA Phone Mode View call logs on screen (“Show incoming 14 — Call/Redial/Hold calls,” “Show Outgoing calls,” “Show missed 15 — Do Not Disturb Overview Calls,” “Show Recent Calls”). 16 — Reply With Text Message * — Conference Call feature only available on Searching contacts phone number (“Search ...
Page 353
MULTIMEDIA NOTE: Uconnect Phone Button WARNING! Your phone must be capable of SMS messaging The Uconnect Phone button on your steering via Bluetooth® for messaging features to work ALWAYS drive safely with your hands on the wheel is used to get into the phone mode and properly.
Page 354
MULTIMEDIA Phone Operation command is given. You can also break the want to call?” in the case where a phone call commands into parts and say each part of the was requested but the specific name was not Operation command when you are asked for it. For recognized.
Page 355
MULTIMEDIA Pair (Link) Uconnect Phone To A Mobile Phone 4. Search for available devices on your Blue- Search for available devices on your tooth®-enabled mobile phone. Bluetooth®-enabled mobile phone (see To begin using your Uconnect Phone, you must below). When prompted on the phone, pair your compatible Bluetooth®...
Page 356
MULTIMEDIA to the Uconnect system at a time. If “No” is 4. Uconnect Phone will display an in process 3. Press the Bluetooth® button on the touch- selected, simply select “Uconnect” from the screen while the system is connecting. screen to display the Paired Audio Devices mobile phone/audio device Bluetooth®...
Page 357
MULTIMEDIA NOTE: 4. Press the X button to exit out of the Settings Phone or Audio Device than the currently For devices which are not made a favorite, the screen. connected device. device priority is determined by the order in 4.
Page 358
MULTIMEDIA Phonebook Download (Automatic Phonebook Depending on the maximum number of selected number to display the options entries downloaded, there may be a short Transfer From Mobile Phone) — If Equipped pop-up. In the pop-up select Add to Favor- delay before the latest downloaded names ites.
Page 359
MULTIMEDIA Ways To Initiate A Phone Call Call By Saying A Phonebook Name Touch-Tone Number Entry Listed below are all the ways you can initiate a 1. Push the VR button on your steering wheel 1. Press the Phone button on the touch- phone call with Uconnect Phone.
Page 360
MULTIMEDIA These can be accessed by pressing the recent box to place the current call on hold and answer NOTE: calls button on the Phone main screen. the incoming call. Only the first 25 characters can be seen on the touchscreen while typing a custom message.
Page 361
MULTIMEDIA Toggling Between Calls Call Continuation Advanced Phone Connectivity If two calls are in progress (one active and one Call continuation is the progression of a phone Transfer Call To And From Mobile Phone call on the Uconnect Phone after the vehicle on hold), press the Swap button on the Phone The Uconnect Phone allows ongoing calls to be main screen.
Page 362
MULTIMEDIA Speak normally, without pausing, just as you Even though the system is designed for many Dry Weather Conditions would speak to a person sitting a few feet/ languages and accents, the system may not Operation From The Driver's Seat ...
MULTIMEDIA STEERING WHEEL AUDIO CONTROLS — IF IPOD®/USB/MP3 CONTROL — IF EQUIPPED The left-hand control is a rocker-type switch with a push-button in the center. The function of the EQUIPPED This feature allows an iPod® or external USB left-hand control is different depending on device to be plugged into the USB port.
MULTIMEDIA iPod® control supports Mini, 4G, Photo, iPod The internal wireless radio operates within Le présent appareil est conforme aux CNR nano®, 5G iPod® and iPhone® devices. Some guidelines found in radio frequency safety stan- d`Innovation, Science and Economic Develop- iPod®...
MULTIMEDIA NOTE: aged to try to correct the interference by one Changes or modifications not expressly or more of the following measures: approved by the party responsible for compli- a. Increase the separation between the ance could void the user’s authority to operate equipment and receiver.
MULTIMEDIA Get Started Notice the visual cues that inform you of your voice recognition system’s status. Cues appear All you need to control your Uconnect system on the touchscreen. with your voice are the buttons on your steering Radio wheel. Helpful hints for using Voice Recognition: Use your voice to quickly get to the AM, FM, or Visit...
MULTIMEDIA TIP: vehicle. Voice Command will not work to adjust steering wheel. After you hear a double beep Your mobile phone must have the full imple- the heated seats or steering wheel if equipped. you can ask Siri to play podcasts and music, get mentation of the Message Access Profile (MAP) directions, read text messages, and many other Navigation (4C NAV)
MULTIMEDIA NOTE: activate Android’s™ VR, which recognizes Apple CarPlay® allows you to use your voice to natural voice commands, to use a list of your interact with Siri through your vehicle’s voice Reply with text message is not compatible smartphone’s features: recognition system, and use your smartphone’s with iPhones®.
CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE minimal daily charge. If you need a rental, it is If for some reason you are still not satisfied, talk to the general manager or owner of the advisable to make these arrangements when FOR YOUR VEHICLE you call for an appointment.
CUSTOMER ASSISTANCE FCA Canada Inc. Customer Center to a TDD or a conventional teletypewriter (TTY) The manufacturer will not stand behind any in the United States, can communicate with the service contract that is not the manufacturer's P.O. Box 1621 manufacturer by dialing 1-800-380-CHRY.
CUSTOMER ASSISTANCE REPORTING SAFETY DEFECTS SE., West Building, Washington, D.C. WARNING! 20590. You can also obtain other infor- In The 50 United States And Washington, Engine exhaust (internal combustion engines mation about motor vehicle safety from D.C. only), some of its constituents, and certain http://www.safercar.gov.
Page 374
CUSTOMER ASSISTANCE A complete working knowledge of the vehicle, Owner's Manuals To access your Owner’s Information online, visit system, and/or components is written in www.mopar.com These Owner's Manuals have been prepared straightforward language with illustrations, with the assistance of service and engineering To order a hard copy of your Owner’s Informa- diagrams, and charts.
INDEX ....254 Air Conditioner Refrigerant Arming System ......151 ......254 ........22 About Your Brakes Air Conditioner System Security Alarm ......... 45 ........97 Adaptive Cruise Control (ACC) (Cruise Control) Air Conditioning Assist, Hill Start ....261 ....... 53 ........340 Adding Engine Coolant (Antifreeze) Air Conditioning Filter Audio Settings...
Page 377
Deck Lid Electrical Power Outlets ......64 Engine ......245 Power Release ........57 Electronic Power Distribution Center (Fuses) Air Cleaner ........254 Defroster, Windshield ......143 Electronic Speed Control (Cruise Control) ..164 Block Heater ........150 Delay (Intermittent) Wipers ......43 Electronic Stability Control (ESC) ....
Page 378
........... 289 ......194 Fuel Hazard Warning Flashers .........183 .......... 290 ........33 Filler Location Fuel Additives Head Restraints .......... 290 ..........33 Filters Clean Air Head Rests ........254 ..........291 Air Cleaner Ethanol Headlights ......53 ......183 .......... 40 Air Conditioning Filler Cap (Gas Cap) Automatic ......
Page 387
It is always the driver’s responsibility to comply with all local laws. This Owner’s Manual has been prepared to help you get acquainted with your new Dodge brand vehicle and to provide a convenient reference source for common questions.