Related Manuals for Alcoa Alumax Bath Enclosures STIKSTALL 792 Series
Summary of Contents for Alcoa Alumax Bath Enclosures STIKSTALL 792 Series
- Page 1 INSTALLATION INSTRUCTIONS BATH ENCLOSURES a product of Alcoa Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com 792 SERIES STIKSTALL SHOWER ENCLOSURE Copyright © Alumax Bath Enclosures 1997. All rights reserved. G03711074 8-1-06...
-
Page 2: Limited Warranty And Remedy
LIMITED WARRANTY AND REMEDY warrants to its dealers, customers, and all subsequent purchasers LUMAX NCLOSURES and users, that the products supplied by it shall be free from material defects in material and workmanship for a period of one (1) year after shipment, provided they are installed and maintained according to A 's recommended practices and installation LUMAX... - Page 3 792 STIKSTALL PARTS LIST 2 Curb Sections (with weep slots) DD. 1 Exterior Door Handle 1 Fixed Glass Panel 2 Drip Plugs 2 90° Anchor Plates 1 90° Post 1 Tapered Drip Vinyl 2 #6 x 1 1/4" Round Head Screws 24 #8 x 1/4"...
- Page 4 The A framework has been designed to work with a variety LUMAX TALL of different door types. To ensure correct installation, this 792 Instruction Sheet is designed to be used by itself with a 790 Framed Pivot Door or with an instruction supplement packed with a 390 Frameless Pivot Door, a 790i Intre-Hinge Door or a 1090 Heavy Frameless Pivot Door.
- Page 5 - ALL DOORS Measure the opening at the bottom of the shower stall and trim the ends of the curb assembly [A] (with weep slots) to fit the shower sill. curb should sit near the centerline of the sill. required, use a file to round the lower ends of the curb assembly to fit the shower sill properly.
- Page 6 - ALL DOORS Place two setting blocks [H] into the curb assembly [A] as shown to support the fixed glass panel [J]. The setting blocks should be positioned approximately 3" from each corner of the glass panel. Remove any protective strips from the glass panel and set it into place on the setting blocks approximately 1/2"...
- Page 7 - 790 DOORS ONLY Strip two clear vinyl jamb seals [L] into the door panel [M] splash guard and the pivot jamb [N] and trim flush at the ends. Both vinyls should be turned to trap water from the shower head. Secure the vinyls with a small quantity of glue or caulk at each end or by carefully crimping the vinyl pocket.
- Page 8 - 790 DOORS ONLY Insert the two #10-24 x 7/16" square head set screws [X] into the threaded holes in the pivot blocks in the top and bottom rails of the glazed door panel [M]. Position the pivot pins 1 1/2" from the pivot side of the door (the side opposite the magnetic strip).
- Page 9 - 790 DOORS ONLY Adjust the drip vinyl [U] by sliding it left or right until it just touches the curb. Trim the vinyl (flush with the pivot end and notch 1/4" longer than the drip rail as shown on the strike end). The drip plug [T] is supplied with a left and right hand plug together.
- Page 10 - ALL DOORS Cut four pieces of the smaller vinyl [FF] 1" longer than the vertical opening (to prevent gapping from shrinkage) and trim the ends on a 45° angle. Using the masking tape guides, center the glass panel [J] in the frame. Cut four short (1" - 2") pieces of the small vinyl and press into both jambs on each side to hold the glass temporarily.
- Page 11 To keep your Alumax Bath Enclosure looking like new we recommend the Alumax ShowerBright Consumer Maintenance Kit. The Consumer Maintenance Kit surface should be applied every 45 to 60 days. To purchase or for more information contact your dealer. Our dealers have the materials to do a professional ShowerBright restoration.
Need help?
Do you have a question about the Alumax Bath Enclosures STIKSTALL 792 Series and is the answer not in the manual?
Questions and answers