Related Manuals for Infatrac MS121A
Summary of Contents for Infatrac MS121A
- Page 1 Wireless Industrial Alarm Adapter User Manual Rev. A Issue Date: 08172015 Document Number: 00101...
- Page 2 Alarm Adapter. Repair of this equipment should only be referred to qualified technical personnel. Infatrac will repair or replace (our option) inoperative units for up to one year from date of manufacture. This excludes damage due to lightning or installer error. Unauthorized modifications void this warranty.
- Page 3 Although this equipment is designed to be long lasting, the electrical components could fail at any time. These Terms and Conditions are a legal contract between you and Infatrac for the title to and use of the Product. BY RETAINING AND USING THE PRODUCT YOU AGREE TO THE TERMS AND CONDITIONS INCLUDING WARRANTY DISCLAIMERS, LIMITATIONS OF LIABILITY AND INDEMNIFICATION PROVISIONS BELOW.
-
Page 4: Table Of Contents
GUI COMMAND LIST ..................... 4 FIRMWARE UPGRADE PROCESS .................. 5 ACC COMMANDS ......................5 Verifying MS121A normal operation ................7 3.6 Periodic testing of MS121A in normal operation ............7 TROUBLESHOOTING ......................10 APPENDIX ..........................10 PRODUCT LABEL ......................10 REAR PANEL ......................... -
Page 5: General Description And Operation
1.3 UL LISTED The Wireless Industrial Alarm Adapter (MS121A) is UL 864 listed and certified, establishing it as suitable for industrial and fire system applications. The MS121A is not to be used for off-premise signaling to a supervising station. 2 INSTALLATION GUIDE Setup and installation of your MS121A is simple, straightforward, and consists of 3 steps: activation, registration, and installation. -
Page 6: Step 2: Registration
(877) 262-6539 option 2 or sending us at email at support@infatrac.com. 2.2 STEP 2: REGISTRATION To register your MS121A to our Sinapsium© version 12.00.21 software, please visit infatrac.com/registration-portal.html and fill out the accompanying questionnaire. After successful registration, you will receive an email containing your username and password with detailed instructions on how to run the Sinapsium©... -
Page 7: Step 3: Installation
MS121A. Also keep in mind that you will need to connect your MS121A to your alarm panel’s 7-21VDC power source using the included DC terminal block (see Appendix 5.6). -
Page 8: Accessing The Graphical User Interface (Gui)
(summarized in Section 3.2 – GUI Command List). You will also be able to modify the MS121A’s host IP and port through this menu. By default, the MS121A is shipped with the host IP and port pointing to the Sinapsium© Monitoring Center. -
Page 9: Firmware Upgrade Process
HyperTerminal, as well as the latest firmware file from your dealer which you can acquire by contacting support at (877) 262-6539 Option 2. Follow the steps in the previous section to access your MS121A’s GUI main menu. Once there, select option 4 (Firmware Upgrade); you will have 30 seconds to send the firmware update. - Page 10 MS121A unable to modify password field. Use default value. <PASSWORD> Default : 0000 UDP: 0 <TYPE> PARAMETERS TCP: 1 IP address of the host <IP> TCP/UDP Port <PORT> Range: 0 – 65535 Write command $HOSTS:OK RETURN VALUE Read command $HOSTS=<TYPE>,<IP>,<PORT>...
-
Page 11: Verifying Ms121A Normal Operation
MS121A ERIODIC TESTING OF IN NORMAL OPERATION Use ACC COMMANDS (see section 3.4) to read data via HOST IP making sure if MS121A works normally. Recommend to implement this periodic testing in every three (3) months. 1. Execute HyperTerminal and enter a name. For example, enter MEID number [FA0]. - Page 12 2. In “Connect To” table, enter detail HOST IP and port number. For example, enter HOST IP: 166.143.116.154 ; host port : 59473. 3. Press ASCII setup in Settings, then check box of Send line ends with line feeds and Echo typed characters locally. support@infatrac.com © 2015 Infatrac, LLC...
- Page 13 ACC$HOSTS? and then enter to next line. Type a string following $HOST? as X, XXX.XXX.XXX.XXX, XXXX. X: IP type, keep “1” XXX.XXX.XXX.XXX: HOST IP XXXX: Port Number Use hyper terminal, must cut/paste the typed string including the space. (see the below pictures) support@infatrac.com © 2015 Infatrac, LLC...
-
Page 14: Troubleshooting
4 TROUBLESHOOTING The following basic troubleshooting procedures are based off the most common issues when setting up a new MS121A. For additional troubleshooting support, please visit our online forum. No Wireless Signal Strength LED’s are illuminated o Power-cycle the device (turn it OFF, wait 10 seconds, then turn ON) -
Page 15: Rear Panel
5.2 REAR PANEL PORT DESCRIPTION Antenna connection Mini-USB connection 4-PIN 4-Pin connection – for developmental use only PHONE LINE Phone line connection DC 7-21VDC Power connection – 7-21VDC current OFF ON Power toggle switch. support@infatrac.com © 2015 Infatrac, LLC... -
Page 16: Front Panel
5.3 FRONT PANEL FRONT PANEL LEDS POSITION ICON COLOR STATE DESCRIPTION GREEN POWER ON POWER STATUS POWER OFF MCU FAULT SERVER STATUS AMBER SERVER CONNECTED ATTEMPTING SERVER AMBER FLASHING CONNECTION INTERNET “ON” AMBER INTERNET STATUS INTERNET “OFF” support@infatrac.com © 2015 Infatrac, LLC... -
Page 17: Device Specifications
Embedded UDP/TP & TCP/IP & HTTP Enhanced AT commands set IS-707.3 AT Commands 3 GPP 27.005, 3GPP 27.007, ITU-T V.25 3GPP 27.010 MUX protocol Mode: Class B, Multi Slot 10 Packet Data Coding Schemes: CS1-CS4 Packet Channel: PBCCH/ PCCCH support@infatrac.com © 2015 Infatrac, LLC... - Page 18 Twist Accept Limit (Negative) 10 dB Dial Tone Tolerance 18 dB Noise Tolerance -12 dB Third Tone Tolerance -16 dB Frequency Deviation Acceptance Max ± 1.5% Frequency Deviation Rejection Min ± 3.5% Power-up Time 30 ms support@infatrac.com © 2015 Infatrac, LLC...
-
Page 19: Installation Setup Diagram
5.5 INSTALLATION SETUP DIAGRAM UNSUPERVISED LINE 2 SUPERVISED LINE 2 support@infatrac.com © 2015 Infatrac, LLC... -
Page 20: Accessories List
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: support@infatrac.com © 2015 Infatrac, LLC... -
Page 21: Maintenance Of Ms121A Backup Battery
One year after shipment in the standard storage condition. The ambient temperature is 20±5℃, the humidity is 45% to 85%, and the pressure is 86kPa to 106kPa. Charge the battery to about 50% SOC each six months during storage. support@infatrac.com © 2015 Infatrac, LLC...