Advertisement
Quick Links
Mudsucker Trash Pump
Sand Cast Aluminum Construction
Thermoplastic Santoprene Diaphragm
Gasoline powered
3" NPT Suction / Discharge Ports
Maximum Temperature 180 F
.075" Keyed Shaft
Self priming to 25 Ft. Lift
Diaphragm pump
Tank Size .052 gal / 2.0 lt
Maximum Solids Handling Capacity: 1-5/8" diameter
Complete with Oil Alert
Wheeler-Rex
3744 Jefferson Road
Ashtabula, OH 44004
www.wheelerrex.com
Phone: 800-321-7950 or 440-998-2788
Fax: 440-992-2925
Email: wheeler@wheelerrex.com
Model 56310
3" Capacity
Advertisement
Related Manuals for Wheeler-Rex 56310
Summary of Contents for Wheeler-Rex 56310
- Page 1 Gasoline powered 3” NPT Suction / Discharge Ports Maximum Temperature 180 F .075” Keyed Shaft Model 56310 Self priming to 25 Ft. Lift 3” Capacity Diaphragm pump Tank Size .052 gal / 2.0 lt ...
- Page 2 Mudsucker Trash Pump Unpacking Positively No Smoking! 2. Check engine oil, fuel levels and gear box oil levels before initial startup each day. Stay away from mov- After unpacking the unit, inspect carefully for any ing parts due to the danger of becoming caught in damage that may have occurred during transit.
- Page 3 Mudsucker Trash Pump 3-prong grounding-type receptacle (as shown in Fig- General Safety Information ure 2); 2 permanently wiring the unit with a grounded 1. Know the pump application, limitations and poten- metal raceway system. (3) using a separate ground tial hazards. wire connected to the bare metal of the motor frame, WARNING or (4) other suitable means.
- Page 4 Mudsucker Trash Pump Assembly 1. Place the pump on a level, solid foundation, locat- 1. Handle on 2” Pump ing it as close to the liquid as possible making the Remove two hex cap screws (Ref No A6) and suction line as short and direct as possible. washers (Ref No A7) from gearbox (Ref No A1).
- Page 5 Mudsucker Trash Pump Do not exceed 60 strokes per minute with the dia- phragm pump. Operation Operate the diaphragm pump in an upright position only. 1. This diaphragm pump is capable of priming “dry” up to fifteen feet; it will prime much faster when it is filled with clean water through priming cap (Ref No W6).
- Page 6 Mudsucker Trash Pump discharge plate (Ref No W7). Replace flapper valve 12. Remove output shaft oil seal (Ref No G23) on flapper pin to locate valve on pump well (Ref No 13. Remove bearings (Ref Nos G15 & G18) from ends of input pinion shaft (Ref No G20) 14.
- Page 7 Mudsucker Trash Pump NOTE: Only qualified service personnel should attempt to repair this unit. Improper repair and/or assembly can cause pump damage, driver damage and/or an elec- trical shock hazard depending on the model.
- Page 8 Mudsucker Trash Pump...
- Page 9 Mudsucker Trash Pump...
- Page 10 Mudsucker Trash Pump...
- Page 11 Mudsucker Trash Pump...
- Page 12 Mudsucker Trash Pump...
- Page 13 Mudsucker Trash Pump...
- Page 14 Mudsucker Trash Pump...
- Page 15 Mudsucker Trash Pump...
- Page 16 Mudsucker Trash Pump Wheeler - Rex • Ashtabula, Ohio Tel: 800-321-7950 440-998-2788 Fax: 440-992-2925 wheeler@wheelerrex.com www.wheelerrex.com...
Need help?
Do you have a question about the 56310 and is the answer not in the manual?
Questions and answers