Advertisement
Read This Before Operating
DO NOT RETURN THE POWERALLEY PRO MACHINE TO THE RETAIL STORE WHERE
USE POWERALLEY LITE-BALLS OR POWERALLEY Pro REAL BASEBALLS IN THE MACHINE
The PowerAlley Pro Pitching Machine uses PowerAlley Soft Lite-Balls, PowerAlley Regular Lite-Balls and
PowerAlley Pro Real Baseballs. Heater Sports recommends using official PowerAlley Lite-Balls or PowerAlley
Pro Real Baseballs in the PowerAlley Pro Pitching Machine. These balls are incredibly accurate, long lasting,
HEATER SPORTS is dedicated to your customer satisfaction. If you experience any trouble with the
operation of the PowerAlley Pro Pitching Machine contact us at: (800) 492-9334 or log on to our
WARNING: THIS PRODUCT IS TO BE USED BY ADULTS ONLY. MAKE SURE MACHINE IS TURNED OFF BEFORE
ASSEMBLY! KEEP HANDS AND ALL BODY PARTS AWAY FROM BALL ENTRY AND EXIT! SERIOUS HAND, EYE, AND
BODILY INJURY MAY OCCUR IF USED INCORRECTLY!
•
Please be sure to read all of the instructions before using the PowerAlley Pro
Pitching Machine to insure the machine is working properly.
•
Parents: Your child should be made aware of the potential dangers of using the
PowerAlley Pro Pitching Machine.
•
Never put your fingers into the PowerAlley Pro Pitching Machine.
•
The PowerAlley Pro is not a toy and an adult should supervise children. It is very important
the batter makes sure the area is clear before swinging a bat.
•
Stay clear of the ball opening while the PowerAlley Pro is operating. Although the balls may be
very light, they may cause eye damage or other injury may occur.
Children must be advised of this danger and appropriate precautions should be taken.
DO NOT use any type of ball other than Heater Sports Balls in this machine.
•
•
Always use a NOCSE approved batting helmet when batting.
•
DO NOT LOOK INTO THE FRONT OF THE MACHINE WHILE THE POWERALLEY PRO IS RUNNING.
Occasionally a ball may get stuck in the machine. The ball may pause and then shoot out and cause
eye injury. If the ball gets stuck, turn off the machine immediately. You should be able to remove the
ball easily by tilting the PowerAlley Pro backwards to eject the ball.
•
Never operate in water or moisture.
•
Always store in a dry area.
PURCHASED. CALL TOLL FREE: (800) 492-9334.
and produce the best performance in the machine.
CUSTOMER SERVICE
website at www.HeaterSports.com.
IMPORTANT
Advertisement
Table of Contents
Related Manuals for Heater Sports PowerAlley
Summary of Contents for Heater Sports PowerAlley
- Page 1 CUSTOMER SERVICE HEATER SPORTS is dedicated to your customer satisfaction. If you experience any trouble with the operation of the PowerAlley Pro Pitching Machine contact us at: (800) 492-9334 or log on to our website at www.HeaterSports.com. WARNING: THIS PRODUCT IS TO BE USED BY ADULTS ONLY. MAKE SURE MACHINE IS TURNED OFF BEFORE...
- Page 2 POWERALLEY PRO PARTS LIST Legs (Qty 3) Pole Ground Pre-Assembled Stakes Pole Clamp (Qty 2) Clamp Knob Tripod Housing (Qty 1) POWERALLEY PRO ASSEMBLY INSTRUCTIONS STEP 1: Slide Legs (A) into Tripod (B) base until push-pin snaps into place. STEP 2: Insert Top Pole (C) into Tripod (B) top until push-pin snaps into place. Tighten Thumb Screw in threaded nut attached to opposite side of the push-pin hole.
- Page 3 POWERALLEY PRO ASSEMBLY (Continued) STEP 3: Remove Thumb Knob & Washers from Pole Clamp Knob & assembly on Housing and slide the housing Washers bolt through the Top Pole (C) holes. IMPORTANT! Tighten Knob When placing the Housing on to the Top Pole (C), make sure the Housing and Top Pole lean forward, not backward.
- Page 4 STEP 1: Before using the PowerAlley Pro pitching machine, use the two Ground Stakes (E) to secure the back legs in place. STEP 2: Plug the PowerAlley Pro into any standard wall outlet and allow the motor to get to full speed then place a ball into the elbow chute.
- Page 5 Check The Air Pressure In The PowerAlley Pitching Machine Tire. Warning: Make sure PowerAlley Pitching Machine is unplugged and the tire is not spinning during these operations.
Need help?
Do you have a question about the PowerAlley and is the answer not in the manual?
Questions and answers