Table of Contents
Related Manuals for NKE NMEA 183
Summary of Contents for NKE NMEA 183
- Page 1 NMEA 183 output interface Product reference: 90-60-357 USER GUIDE & INSTALLATION GUIDE – Sailing competition Z.I. Kerandré – Rue Gutenberg – 56700 HENNEBONT- FRANCE http://www.nke.fr – After sale service n° 33 297 365 685...
-
Page 2: Table Of Contents
TABLE OF CONTENTS PRESENTATION ............................ 3 INFORMATION CONVERTED BY THE NMEA OUTPUT INTERFACE ..........3 FRAMES TRANSMITTED BY THE NMEA OUTPUT INTERFACE ............4 TECHNICAL SPECIFICATIONS ......................6 DIAGNOSTIC FOR 1 LEVEL TROUBLESHOOTING................. 7 INSTALLATION ............................7 ........................7 IST OF ACCESSORIES ...................... -
Page 3: Presentation
1. PRESENTATION The NMEA output interface allows the conversion of the Topline data present on the NMEA data bus, so as to allow the interfacing between your Topline network and the equipment from a different manufacturer. When the NMEA output interface is connected to the COM port of a PC with navigation software, the navigation information (heading and distance to Waypoint, cross-track error) may be resent from the same COM port on the Topline network via a Gyrographic, a TL25 or an NMEA input interface. -
Page 4: Frames Transmitted By The Nmea Output Interface
3. FRAMES TRANSMITTED BY THE NMEA OUTPUT INTERFACE The frames transmitted by the NMEA interface depend on the sensors connected to the Topline bus. Surface speed and compass heading: $IIVHW,x .x,T,x.x,M,x.x,N,x.x,K*hh I I__I_Surface speed in kph I__I_Surface speed in knots I__I_Magnetic compass heading I__I_True compass heading Total log and daily log:... - Page 5 $IIVWT,x.x,a,x.x,N,x.x,M,x.x,K*hh I__I_Wind speed in kph I__I_Wind speed in m/s I_ I_Wind speed in knots I__I_True wind angle from 0° to 180° , L=port, R=starboard Air temperature: $IIMTA,x.x,C*hh I__I_Temperature in degrees C Heading magnetic: $IIHDG,x.x,,,,*hh I_Heading magnetic $IIHDM,x.x,M*hh I__I_Heading magnetic Heading true: $IIHDT,x.x,T*hh I__I_Heading true Barometer:...
-
Page 6: Technical Specifications
Bottom heading and speed: $IIVTG,x.x,T,x.x,M,x.x,N,x.x,K,A*hh I__I_Bottom speed in kph I__I_Bottom speed in knots I__I_Magnetic bottom heading I__ I_True bottom heading Cross-track error: $IIXTE,A,A,x.x,a,N,A*hh I_Cross-track error in miles, L= left, R= right Heading and distance to waypoint: $IIRMB,A,x.x,a,,,IIII.II,a,yyyyy.yy,a,x.x,x.x,x.x,A,a*hh I_Speed to WP in knots I_True heading to destination in degrees I_Distance to destination in miles I_ ___ I_Longitude of the WP to destination, E/W... -
Page 7: Diagnostic For
Upon startup, the NMEA output interface sends a proprietary frame that indicates the Firmware’s version number and creation date. 5. DIAGNOSTIC FOR 1 LEVEL TROUBLESHOOTING. This chapter can help you rapidly resolve minor problems which do not require the intervention of a specialist. -
Page 8: Installation Of The Interface
Installation of the interface Fix the housing using Ø4 screws Unit : mm Figure 1 CAUTION: Connecting the NMEA output interface must be carried out with the power switched off. -NMEA output interface user guide 183 33-60-357-001 REV1... - Page 9 Connecting the NMEA output interface to a PC and a Gyrographic • Make the bus cable run from the NMEA output interface to the TOPLINE terminal box of your installation. • Connect the bus cable inside the terminal box as shown in Figure 2. •...
-
Page 10: Pc And Atl25
Connecting the NMEA output interface to a PC and a TL25 • Make the bus cable run from the NMEA output interface to the TOPLINE terminal box of your installation. • Connect the bus cable inside the terminal box as shown in Figure 3. •... -
Page 11: Input Interface
Connecting the NMEA output interface to a PC and an NMEA input interface • Make the bus cable run from the NMEA output interface to the TOPLINE terminal box of your installation. • Connect the bus cable inside the terminal box as shown in Figure 4. •... - Page 12 Connecting the NMEA output interface to a listening apparatus • Make the bus cable run from the NMEA output interface to the TOPLINE terminal box of your installation. • Connect the bus cable inside the terminal box. • Cut the SubD connector. •...
Need help?
Do you have a question about the NMEA 183 and is the answer not in the manual?
Questions and answers