Advertisement
4.1.
mode Description.
Step 1 -
Step 2 -
Voltage
Battery
Selection
Selection 'V'
6V
Gel
AGM
STd
12V
Gel
AGM
STd
lITHIUM
4.2.
9 stage charging.
Stage 1: Desulphation: Pulses of current and voltage.
Stage 2: Battery charge to 25% capacity using 50% constant current.
Stage 3: Battery charge to 50% capacity using max. current.
Stage 4: Battery charge to 75% capacity using constant voltage.
Stage 5: Analysis: Analysing power capacity.
Stage 6: Recond: If power capacity is low use Recond to attempt recovery.
Stage 7: Battery charge to 100% capacity using constant voltage.
Stage 8: Diagnosis: Check battery for 100% charged.
Stage 9: Maintenance: Battery fully charged.
4.3.
coNNectINg to the BatterY.
Note: the charger should be connected to the battery before connecting to mains supply.
4.3.1.
The output cable from the charger terminates in a polarity conscious socket into which the two alternative leads can be connected.
4.3.2.
one lead set has two colour coded battery clamps which can be quickly attached to and detached from the battery posts.
The second lead is for semi permanent connection to the battery via eyelets.
4.4.
chargINg a NegatIVe eartheD BatterY.
4.4.1.
ensure that the black clamp on the clamp lead is not touching the battery or the fuel line.
4.4.2.
Connect the positive (+) red clamp to the positive (+) battery post and connect the negative (-) black clamp to the negative (-) battery
post or vehicle chassis.
4.5.
chargINg a posItIVe eartheD BatterY.
4.5.1.
ensure that the red clamp on the clamp lead is not touching the battery or the fuel line.
4.5.2.
Connect the negative (-) black clamp to the negative (-) battery post and connect the positive (+) red clamp to the positive (+) battery
post or vehicle chassis.
4.6.
BatterY Not coNNecteD to a VehIcLe.
4.6.1.
Connect the (+) red clamp to the positive (+) battery post and connect the (-) black clamp to the negative (-) battery post.
4.7.
permaNeNt coNNectIoN to VehIcLe usINg eYeLet LeaD.
4.7.1.
Connect the eyelet on the red (+) wire to the positive (+) battery terminal and connect the eyelet on the black (-) wire to the negative (-)
battery terminal.
4.8.
chargINg moDe seLectIoN (see chart sectIoN 4.1).
4.8.1.
Choice of charging mode depends on battery rated voltage and battery type.
4.8.2.
When charging mode is selected, enter charging by pressing Enter/Exit button.
4.8.3.
When charging is complete disconnect the unit from the mains power supply before disconnecting from the battery.
© Jack Sealey limited
Step 3 -
Step 4 -
Charging mode
Start charging
Selection (A)
2A
eNTER / EXIT
4A
6.5A
AUTO
WInTeR
mAInTenAnCe
2A
4A
6.5A
AUTO
ReCond
WInTeR
SUPPLY
mAInTenAnCe
4A
AUTO
mAInTenAnCe
Original Language Version
Charging status
6V 2A Charging Mode
6V 4A Charging mode
6V 6.5A Charging mode
6V Auto mode
6V Winter mode
6V Maintain mode
12V 2A Charging mode
12V 4A Charging mode
12V 6.5A Charging mode
12V Auto mode
12V Maintain mode
12V Winter mode
12V Supply mode
12V Maintain mode
12V 4A Charging mode
12V Auto mode
12V Maintain mode
AUTOCHARGE650HF
Applicable battery
capacity (Ah)
1.3 -60Ah
2.6-120Ah
3.3-200Ah
/
/
/
1.3-60Ah
2.6-120Ah
3.3-200Ah
/
/
/
/
/
2.6-120Ah
/
/
Issue 1 22/08/18
Advertisement
