Advertisement
CLMIR - H
ANDHELD
Description
The CLMIR Handheld Infrared Transmitter is capable of
operating over an unobstructed range of approximately 75 feet.
Within this range, scenes can be selected, raised and lowered,
and lighting may be turned On and Off using the handheld,
wireless remote transmitter. In addition, the CLMIR is capable
of controlling up to four different Brilliance II, MultiSet Pro,
Compose PLC or Lytemode control station groups.
Unpack Procedure
The CLMIR Handheld Infrared Transmitter is powered by two
AAA batteries (included).
1. Remove CLMIR unit and two AAA batteries from clam shell
package.
2. Install batteries in CLMIR unit and close compartment.
3. Proceed to Programming and Operation section.
The Philips Controls product, when properly installed and under normal conditions of use (without overload, abuse or alteration), is warranted to you, the original user, for a period
of three years form the date of original retail purchase, to be free from defects in materials and workmanship. If during the warranty period you believe the purchased product or any
part thereof has such a defect, you must return the product (or part) at your cost during such period, with proof of purchase (or if installed by a third-party a written explanation of
installation transaction with proof of date), to Philips Controls, 2828 Trade Center Dr. Ste. 130B, Carrollton, TX 75007, for repair or replacement (or to an authorized Philips Controls
supplier which agrees in advance to handle the return and replacement by factory authorization). If the product or part is found by Philips Controls to have been defective in material
or workmanship it will be repaired or replaced (as deemed necessary by Philips Controls), and the replacement will be returned to you free of charge. The original user is solely
responsible for any costs associated with removal and re-installation of the product and shipping to Philips Controls or its authorized supplier.
PHILIPS CONTROLS LIMITS THE DURATION OF THE IMPLIED WARRANTY OF MERCHANTABILITY WITH RESPECT TO THE PRODUCT TO THE LIMITED WARRANTY PERIOD SET FORTH
ABOVE, AND OTHERWISE DISCLAIMS ALL IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT AND ITS PARTS. Some states disallow certain limitations on implied warranties so
you should consult your state law if you have a questions regarding this limitation and disclaimer. Philips Controls disclaims any and all liability for incidental, consequential, special
or indirect damage arising out of any claimed breach of warranty or otherwise. However, some states do not allow exclusion or limitation of such damages, so this disclaimer may not
apply to you.
The remedy provided in the Limited Warranty for defective products is the user's sole and exclusive remedy, subject to your state law. Further, this Warranty gives the user specific legal
rights, and the user may also have other rights which may vary from state to state.
If you believe warranty claim is warranted, you may contact your nearest authorized Philips Controls supplier. If one does not exist in your area, please contact Philips Controls Customer
Service at the above address (or at 1-800-526-2731), or please visit us at www.lolcontrols.com.
Lightolier Controls
2828 Trade Center Drive, Suite 130B
Carrollton, Texas 75007
Lightolier Controls is a Philips Controls brand
I
T
NFRARED
RANSMITTER
Programming and Operation
Programming:
The wall keypad must be enabled to receive the IR signal before the sensor will work. To enable
the keypad, perform the following sequence of keystrokes on the keypad. The Handheld Infrared
Transmitter is already configured to control up to four different keypad addresses (rooms).
1. On the wall keypad, press and hold the A and D buttons
for three seconds. The A, B, C, D and OFF keys will
illuminate with one of them blinking. (The keypad may
be custom engraved to change the labels.) Button A
refers to the keypad being configured as Room 1, B to
Room 2, C to Room 3, and D to Room 4. If OFF is
blinking, the infrared receiver is disabled. Refer to the
drawing at right. The factory default is Room 1 (A).
2. Press the desired Room Number or OFF. This will con-
figure the keypad as that room or disable infrared
input. The selection will blink.
3. Press ON to save and exit.
Operation:
Use the CLMIR unit to remotely operate the corresponding con-
trol station.
NOTE: This system is based on line-of-sight operations, therefore, the receiver must be able to
"See" the transmitter. Any obstruction between the transmitter and receiver may adversely affect
the performance of the unit.
THREE YEAR LIMITED WARRANTY
Programming and Operation
Ellipse Series
Wall Keypad
Technical/Sales assistance: 1-800-526-2731
Made in U.S.A. ©2008 Philips Controls.
www lolcontrols com
P/N 85-6348A0
Instructions
ON
A
B
C
D
OFF
Advertisement
