Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Livassured NightWatch Livanova
Summary of Contents for Livassured NightWatch Livanova
- Page 1 Technical description Nightwatch for Livanova...
-
Page 3: Table Of Contents
Contents Contents of the Livassured NightWatch kit What does the NightWatch detect? Explaining the parts Signals of the arm module and the alarm unit a. Arm module and alarm unit are similar b. Specifics arm module c. Specifics alarm unit Putting the NightWatch into use a. -
Page 5: Contents Of The Livassured Nightwatch Kit
Contents of the Livassured NightWatch kit In the Livassured NightWatch kit the following parts are included: 1 Alarm unit 2 Power supply for alarm unit (black) 3 Arm module 4 Charger for arm module (white) 5 Strap 6 Strap clips... -
Page 6: What Does The Nightwatch Detect
What does the NightWatch detect? The NightWatch aims at detecting nocturnal clinically urgent epilepsy seizures. During the night’s rest of the person suffering from epilepsy (hereafter: the wearer), the surroundings can be alarmed when an ‘urgent seizure’ takes places. This includes tonic-clonic, prolonged tonic and hyper motoric seizures. -
Page 7: Explaining The Parts
Explaining the parts Bracelet: arm module and strap Alarm unit The arm module is the device that is placed on the upper arm The white square box is the alarm unit that delivers both light and (between biceps and shoulder). With the help of the two green sound signals. -
Page 8: Signals Of The Arm Module And The Alarm Unit
Signals of the arm module and the alarm unit The arm module and the alarm unit give light signals, which the alarm unit supports with sound. BEEP Hereunder these signals are explained. Red LED blinks slowly (and alarm unit beeps) •... -
Page 9: Specifics Arm Module
c. Specifics alarm unit The alarm module and the alarm unit are too far apart. Position the alarm unit closer. If this does not solve the problem, the NightWatch is defective. Orange LED burns continuously • The alarm unit is connected to electricity grid. 4 BEEPS 4 BEEPS 4 BEEPS... - Page 10 Alarm unit: operate the alarm sound LEDs Buttons ‘a’ and ‘b’ These buttons allow the following: • Press one of these buttons (it does not matter which one) for about two seconds while the seizure alarm goes off if you want to shut off the sound.
-
Page 11: Putting The Nightwatch Into Use
Measure the contour of you Bend your arm when you m without stretching the strap Bend your arm when you m Putting the NightWatch into use a. Customizing the bracelet Cut the strap at the marking point. Required: • strap •... - Page 12 Attach each clip in the fissure of the arm module from white side to If the strap feels too tight or too loose: dark gray side, have the strap stick out at the dark gray side of the 1) Tear out the strap upwards. Attach the 2 clips in the slots of the device.
-
Page 13: First Activation And Charging Arm Module
b. First activation and charging arm module The first activation is a one-time action: • Take a pen / pencil. • On the dark gray side of the arm module you see a slide knob. Using the pen / pencil, slide this knob to the middle of the module. This activates the arm module. -
Page 14: Putting The Alarm Unit Into Use
c. Putting the alarm unit into use d. Daily use Connect the arm module to the charger. • Roll up the sleeve of the wearer. • Take the arm module from the charger. The two bright green LEDs Connect the power supply to the alarm unit, walk to the spot where on the dark grey side start to burn. -
Page 15: Connecting Arm Module And Alarm Unit
e. Connecting arm module and alarm unit 3. Put the arm module on, make sure that it makes good contact with your skin and lay down. Check whether the LED on the The arm module and the alarm unit are connected with each other module and/or alarm unit stays continually green to make sure on delivery. - Page 16 www.livassured.nl...