Related Manuals for Ricoh Brz-P1 Series
Summary of Contents for Ricoh Brz-P1 Series
- Page 1 This course explains how to service the Brz-P1/MF1 series of black-and- white MFPs and printers. To learn about this machine, please study the user’s guide and the field service manual in addition to this TTP.
- Page 2 This section takes a quick look at the components of the machine.
- Page 3 These models will replace the Sh-P1/MF1 series.
- Page 4 In the Brz series, there is no maintenance kit for the users to replace PM parts.
- Page 5 No additional notes...
- Page 6 No additional notes...
- Page 7 No additional notes...
- Page 8 No additional notes...
- Page 9 No additional notes...
- Page 10 No additional notes...
- Page 11 1. ADF Lower the ADF over originals placed on the exposure glass. If you load a stack of originals in the ADF, the ADF will automatically feed the originals one by one. 2. Exposure glass Place originals face down here. 3.
- Page 12 1. ADF extender Pull this extender to support large paper. 2. Vents Prevent overheating. 3. Extender for the bypass tray Pull this extender out when loading A4 , 8.5 x 11 or larger paper in the bypass tray. 4. Bypass tray 5.
- Page 13 No additional notes...
- Page 14 1. IEEE 1284 port (optional) Port for connecting an IEEE 1284 interface cable 2. Gigabit Ethernet port Port for using a 1000BASE-T, 100BASE-TX, or 10BASE-T cable Use this interface to connect the machine to a network. If you use an Ethernet interface cable that supports 1000BASE-T, set [Ethernet Speed] to [Auto Select: Enable 1Gbps] in [Interface Settings] in [System Settings].
- Page 15 1. Top cover Open to access the inside of the printer and remove jammed paper. Open here to replace the print cartridge. 2. Standard tray Output is stacked here with the print side down. 3. Control panel 4. Vents5. Paper size dial Use this dial to specify the paper size.
- Page 16 the paper. 12. Tray Extension Pull this fence to prevent paper from falling off.
- Page 17 1. Rear cover Open to access the inside of the printer. Open here to replace the fusing unit. 2. Power connector Connect the power cord to the printer. Insert the other end into an electrical outlet. 3. USB port A Connect external devices such as a card authentication device, etc.
- Page 18 This section takes a quick look at the important points about installing the machine. For full details see the service and operation manuals.
- Page 19 No additional notes...
- Page 20 No additional notes...
- Page 21 No additional notes...
- Page 22 No additional notes...
- Page 23 No additional notes...
- Page 24 No additional notes...
- Page 25 *1 There is no difference between the left and right USB ports. *2 MP 501SPF/601SPF only...
- Page 26 *1 MP 501SPF/601SPF only *2 SP 5300DN/5310DN only...
- Page 27 No additional notes...
- Page 28 This section takes a quick look at the components of the machine.
- Page 29 No additional notes...
- Page 30 No additional notes...
- Page 31 No additional notes...
- Page 32 No additional notes...
- Page 33 No additional notes...
- Page 34 No additional notes...
- Page 35 No additional notes...
- Page 36 No additional notes...
- Page 37 No additional notes...
- Page 38 No additional notes...
- Page 39 This section takes a look at the components of each section, and any important points about replacing parts.
- Page 40 No additional notes...
- Page 41 No additional notes...
- Page 42 No additional notes...
- Page 43 No additional notes...
- Page 44 No additional notes...
- Page 45 No additional notes...
- Page 46 No additional notes...
- Page 47 No additional notes...
- Page 48 No additional notes...
- Page 49 No additional notes...
- Page 50 There is also a quenching lamp (LED array).
- Page 51 There is also a quenching lamp (LED array).
- Page 52 No additional notes...
- Page 53 No additional notes...
- Page 54 There is also a sensor to check if toner remains in the development unit.
- Page 55 There is also a sensor to check if toner remains in the development unit.
- Page 56 No additional notes...
- Page 57 No additional notes...
- Page 58 The transfer roller transfers toner from the drum to the paper. The discharge plate discharges the paper, so that it separates from the drum.
- Page 59 The transfer roller transfers toner from the drum to the paper. The discharge plate discharges the paper, so that it separates from the drum.
- Page 60 No additional notes...
- Page 61 No additional notes...
- Page 62 No additional notes...
- Page 63 No additional notes...
- Page 64 No additional notes...
- Page 65 No additional notes...
- Page 66 No additional notes...
- Page 67 No additional notes...
- Page 68 No additional notes...
- Page 69 No additional notes...
- Page 70 No additional notes...
- Page 71 This section takes a quick look at the main points about the replacement procedures. For full details, see the service manual.
- Page 72 No additional notes...
- Page 73 Example: Left upper cover...
- Page 74 No additional notes...
- Page 75 No additional notes...
- Page 76 The printer model looks a bit different, but the screw in the same place is also a small screw.
- Page 77 This diagram shows the MFP version. The printer version is almost the same.
- Page 78 No additional notes...
- Page 79 No additional notes...
- Page 80 There is no such problem with the other serial number, which is on the BiCU board.
- Page 81 No additional notes...
- Page 82 No additional notes...
- Page 83 No additional notes...
- Page 84 The End...